Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P0ABF-123    Hybrid Battery Pack Current Sensor Circuit

DTC    P0AC1-123    Hybrid Battery Pack Current Sensor "A" Circuit Low

DTC    P0AC2-123    Hybrid Battery Pack Current Sensor "A" Circuit High

for Preparation Click here


DESCRIPTION


  1. The battery current sensor, which is mounted on the positive cable side of the HV battery assembly, detects the amperage that flows into the HV battery. The battery smart unit inputs a voltage, which varies between 0 and 5 V in proportion to the amperage, into the IB terminal from the battery current sensor. An output voltage of the battery current sensor below 2.5 V indicates that the HV battery is being discharged, and above 2.5 V indicates that the HV battery is being charged. The power management control ECU determines the charging and discharging amperage of the HV battery based on the signals that are input to its IB terminal from the battery smart unit, and calculates the SOC (state of charge) of the HV battery through the accumulated amperage.


    A108798E16


DTC No.
DTC Detection Condition
Trouble Area
P0ABF-123
Power source voltage of the battery current sensor is excessively low/high.
(1 trip detection logic)
  1. Hybrid battery junction block
  2. Battery smart unit
  3. Wire harness or connector
P0AC1-123
The battery current sensor output value is excessively low.
(1 trip detection logic)
P0AC2-123
The battery current sensor output value is excessively high.
(1 trip detection logic)

Related Data List 
DTC No.
Data List
P0ABF-123
P0AC1-123
P0AC2-123
Batt Pack Current Val

MONITOR DESCRIPTION

If the battery smart unit detects a malfunction in the battery current sensor, the power management control ECU (HV CPU) illuminates the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0ABF (INF 123): Power-supply circuit for current sensor malfunction (GND short/ +B short)
P0AC1 (INF 123): Current sensor circuit malfunction (GND short)
P0AC2 (INF 123): Current sensor circuit malfunction (open)
Required sensors / components
Battery current sensor
Frequency of operation
Continuous
Duration
TMC's intellectual property
MIL operation
TMC's intellectual property
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TMC's intellectual property
Other conditions belong to TMC's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


TMC's intellectual property
-

COMPONENT OPERATING RANGE


Battery smart unit
DTC P0ABF (INF 123) is not detected
DTC P0AC1 (INF 123) is not detected
DTC P0AC2 (INF 123) is not detected

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for 30 seconds or more.
  5. Turn the power switch on (IG) and wait for 10 seconds or more.
  6. Perform the universal trip.
  7. Enter the following menus: Powertrain / HV / Trouble Codes.
  8. Read the current DTCs.

    HINT:
    1. If a current DTC is output, the system is malfunctioning.
    2. If a current DTC is not output and want to confirm permanent DTC, perform the following procedure.

  9. Check that permanent DTCs are cleared.

WIRING DIAGRAM


A308307E01


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals.

    HINT:
    At least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

NOTICE:
After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the power switch on (IG) and wait for 10 seconds or more.

1.CHECK DTC OUTPUT (DTC P0AFC-123 IS OUTPUT)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check and record any HV system DTCs, INF codes and freeze frame data.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    P0AFC-123 is not output.
    A
    P0AFC-123 is also output.
    B

  1. Disconnect the Techstream from the DLC3.



B
GO TO DTC CHART
A


2.CHECK HARNESS AND CONNECTOR (HYBRID BATTERY JUNCTION BLOCK - BATTERY SMART UNIT)

NOTICE:
Be sure to wear insulated gloves.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).



    A217836E03
  1. Disconnect only the c1 connector of the battery smart unit.

  1. Disconnect the c4 battery current sensor connector from the hybrid battery junction block.



    A221325E03
  1. Measure the resistance according to the value(s) in the tables below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    c1-1 (IB) - c4-3 (IB)
    Power switch off
    Below 1 Ω
    c1-6 (GIB) - c4-2 (GIB)
    Power switch off
    Below 1 Ω
    c1-5 (VIB) - c4-1 (VIB)
    Power switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    c1-1 (IB) or c4-3 (IB) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    c1-6 (GIB) or c4-2 (GIB) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    c1-5 (VIB) or c4-1 (VIB) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Battery Smart Unit)
    *b
    Front view of wire harness connector
    (to Hybrid Battery Junction Block)

  1. Connect the battery smart unit connector.

  1. Connect the c4 battery current sensor connector to the hybrid battery junction block.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK BATTERY SMART UNIT (VIB VOLTAGE)

NOTICE:
Be sure to wear insulated gloves.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the power switch on (IG).

    NOTICE:
    Turning the power switch on (IG) with the service plug grip removed causes an interlock switch system DTC (P0A0D-350) to be set. Use the Techstream to clear the DTCs (Click here).



    A214447E08
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    c1-5 (VIB) - c1-6 (GIB)
    Power switch on (IG)
    4.6 to 5.4 V

    Text in Illustration 
    *a
    Component with harness connected
    (Battery Smart Unit)

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.



NG
REPLACE BATTERY SMART UNIT (Click here)
OK


4.CHECK BATTERY SMART UNIT

CAUTION:
Be sure to wear insulated gloves.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the power switch on (IG).

    NOTICE:
    Turning the power switch on (IG) with the service plug grip removed causes an interlock switch system DTC (P0A0D-350) to be set. Use the Techstream to clear the DTCs (Click here).



    A214447E09
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    c1-1 (IB) - c1-6 (GIB)
    Power switch on (IG)
    2.46 to 2.54 V

    Text in Illustration 
    *a
    Component with harness connected
    (Battery Smart Unit)

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.



NG
REPLACE HYBRID BATTERY JUNCTION BLOCK (Click here)
OK

REPLACE BATTERY SMART UNIT (Click here)