Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P0AC0-123    Hybrid Battery Pack Current Sensor Circuit Range / Performance

for Preparation Click here


DESCRIPTION

Refer to the Description for DTC P0ABF-123 .

DTC No.
DTC Detection Condition
Trouble Area
P0AC0-123
The offset value of the battery current sensor is excessively high, or the battery current sensor output is stuck.
(1 trip detection logic)
  1. Hybrid battery junction block
  2. Battery smart unit

Related Data List 
DTC No.
Data List
P0AC0-123
Batt Pack Current Val

MONITOR DESCRIPTION

If the battery smart unit detects a malfunction in the battery current sensor, the power management control ECU (HV CPU) will illuminate the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0AC0 (INF 123): Current sensor malfunction
Required sensors / components
Battery current sensor
Frequency of operation
Continuous
Duration
TMC's intellectual property
MIL operation
TMC's intellectual property
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TMC's intellectual property
Other conditions belong to TMC's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


TMC's intellectual property
-

COMPONENT OPERATING RANGE


Battery smart unit
P0AC0 (INF 123) is not detected

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off.
  5. Turn the power switch on (IG), wait for 10 seconds or more and then turn the power switch off.
  6. Turn the power switch on (IG) and turn the Techstream on.
  7. Perform a universal trip.
  8. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
  9. Read the current DTCs.

    HINT:
    1. If a current DTC is output, the system is malfunctioning.
    2. If a current DTC is not output and want to confirm permanent DTC, perform the following procedure.

  10. Check that permanent DTCs are cleared.

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals.

    HINT:
    At least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

NOTICE:
After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

HINT:
After the repair, clear the DTCs, perform the following operations, and check that no DTCs (including pending DTCs) are output.
  1. Drive the vehicle on urban roads for approximately 10 minutes.

1.CHECK DTC OUTPUT (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check and record any HV system DTCs, INF codes and freeze frame data.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    Only DTC P0AC0-123 is output or DTC P0AC0-123 and DTCs other than those in the following table are output.
    A
    Any of the DTCs in the following table are output at the same time.
    B

    DTC No.
    Relevant Diagnosis
    P0A95-123
    High Voltage Fuse
    P0ABF-123
    Hybrid Battery Pack Current Sensor Circuit
    P0AC1-123
    Hybrid Battery Pack Current Sensor "A" Circuit Low
    P0AC2-123
    Hybrid Battery Pack Current Sensor "A" Circuit High
    P0AFC-123
    Hybrid Battery Pack Sensor Module
    P0B3D-123, P0B42-123, P0B47-123, P0B4C-123, P0B51-123, P0B56-123, P0B5B-123, P0B60-123, P0B65-123, P0B6A-123, P0B6F-123, P0B74-123, P0B79-123, P0B7E-123, P0B83-123
    Hybrid Battery Voltage Sensor "A - O" Circuit Low

  1. Turn the power switch off.

  1. Disconnect the Techstream from the DLC3.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

    NOTICE:
    Do not turn the power switch on (READY).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Battery block Vol -V01 to V14.

    NOTICE:
    Select "Battery block Vol -V01 to V14" only. (Do not select any other Data List items.)



  1. Check the voltage of each "Battery block Vol" of "Battery block Vol -V01 to V14" in the Data List with the power switch on (IG).


    A315508E01

    Specified Condition:
    Any "Battery block Vol" changes by 0.3 V or more, 60 seconds after the power switch is turned on (IG). (the difference between the maximum and minimum voltage is 0.3 V or more.)

    Result:
    Result
    Proceed to
    The change in voltage of any "Battery block Vol" is 0.3 V or more.
    A
    Other than above.
    B



B
REPLACE HYBRID BATTERY JUNCTION BLOCK (Click here)
A

REPLACE BATTERY SMART UNIT (Click here)