Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P3011-123    Battery Block 1 Becomes Weak

DTC    P3012-123    Battery Block 2 Becomes Weak

DTC    P3013-123    Battery Block 3 Becomes Weak

DTC    P3014-123    Battery Block 4 Becomes Weak

DTC    P3015-123    Battery Block 5 Becomes Weak

DTC    P3016-123    Battery Block 6 Becomes Weak

DTC    P3017-123    Battery Block 7 Becomes Weak

DTC    P3018-123    Battery Block 8 Becomes Weak

DTC    P3019-123    Battery Block 9 Becomes Weak

DTC    P3020-123    Battery Block 10 Becomes Weak

DTC    P3021-123    Battery Block 11 Becomes Weak

DTC    P3022-123    Battery Block 12 Becomes Weak

DTC    P3023-123    Battery Block 13 Becomes Weak

DTC    P3024-123    Battery Block 14 Becomes Weak

for Preparation Click here


DESCRIPTION

  1. Refer to the Description for DTC P0A80-123 .

DTC No.
DTC Detection Condition
Trouble Area
P3011-123
P3012-123
P3013-123
P3014-123
An internal malfunction of the HV battery is detected and the difference in voltage between each battery block or the internal resistance of each battery block is higher than the specified value.
(1 trip detection logic)
  1. HV battery assembly
  2. Battery smart unit
P3015-123
An internal malfunction of the HV battery is detected and the difference in voltage between each battery block or the internal resistance of each battery block is higher than the specified value.
(1 trip detection logic)
  1. HV battery assembly
  2. Battery smart unit
  3. Service plug grip
P3016-123
P3017-123
P3018-123
P3019-123
P3020-123
P3021-123
P3022-123
P3023-123
P3024-123
An internal malfunction of the HV battery is detected and the difference in voltage between each battery block or the internal resistance of each battery block is higher than the specified value.
(1 trip detection logic)
  1. HV battery assembly
  2. Battery smart unit

HINT:
  1. These DTCs can be stored after clearing DTCs and driving the vehicle for approximately 10 minutes.
  2. These DTCs are stored when a malfunction is detected in the HV battery or a battery smart unit. However, depending on the driving conditions, the malfunction may not be reproduced if the status of the HV battery changes. If internal resistance is abnormal, the voltage of the battery blocks indicated by the DTCs are likely to decrease more than others blocks voltage during acceleration (discharging), and increase more during deceleration (charging).
    1. When the HV battery is malfunctioning:
      1. - Voltage of 1 or a few battery blocks has dropped.
      2. - Voltage of all battery blocks is output randomly with no certain pattern.
    2. When the battery smart unit is malfunctioning:
      1. - Differences in battery block voltages have a certain pattern.


Related Data List 
DTC No.
Data List
P3011-123
P3012-123
P3013-123
P3014-123
P3015-123
P3016-123
P3017-123
P3018-123
P3019-123
P3020-123
P3021-123
P3022-123
P3023-123
P3024-123
  1. Internal Resistance R01 to R14
  2. Battery Block Vol -V01 to V14
The following items can be helpful when performing repairs:
Data List
  1. State of Charge (All Bat)
  2. Ready Signal
  3. Vehicle Spd
  4. Accelerator Degree
  5. Shift Sensor Shift Pos
  6. Engine Revolution
  7. Power Resource VB
  8. Batt Pack Current Val
  9. Auxiliary Battery Vol
  10. Battery Low Time
  11. DC Inhibit Time
  12. SOC after IG-ON
  13. Status of Charge Max
  14. Status of Charge Min
  15. DTC Clear Run Distance
  16. Engine Run Time
Operation History Data
  1. Main Battery Low Voltage

MONITOR DESCRIPTION

If there is an abnormal internal resistance or electromotive voltage in the battery blocks, the battery smart unit determines that a malfunction has occurred. When the malfunction detection condition is satisfied, the power management control ECU (HV CPU) will illuminate the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P3011 to P3024 (INF 123): Rationality
Required sensors / components
HV battery
Frequency of operation
Continuous
Duration
TMC's intellectual property
MIL operation
TMC's intellectual property
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TMC's intellectual property
Other conditions belong to TMC's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


TMC's intellectual property
-

COMPONENT OPERATING RANGE


Battery smart unit
DTC P3011 (INF 123) to P3024 (INF 123) is not detected

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for 30 seconds or more.
  5. Turn the power switch on (IG) and turn the Techstream on.
  6. Turn the power switch on (READY).
  7. Perform a universal trip.
  8. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
  9. Read the current DTCs.

    HINT:
    1. If a current DTC is output, the system is malfunctioning.
    2. If a current DTC is not output and want to confirm permanent DTC, perform the following procedure.

  10. Check that permanent DTCs are cleared.

INSPECTION PROCEDURE

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Drive the vehicle on urban roads for approximately 10 minutes.
    (This DTC may not be stored if the vehicle is stopped or being driven at a constant speed)

1.CHECK DTC OUTPUT (DTC P0AFC-123 IS OUTPUT)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check and record any HV system DTCs, INF codes and freeze frame data.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    P0AFC-123 is not output.
    A
    P0AFC-123 is also output.
    B

  1. Disconnect the Techstream from the DLC3.



B
GO TO DTC CHART
A


2.CHECK BATTERY SMART UNIT
  1. Ensure the safety of the areas in front and at the back of the vehicle.

  1. Apply the parking brake and secure the wheels using chocks.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (READY).

  1. Fully warm up the engine and turn the air conditioning off.

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Battery Block Vol -V01 to V14.

  1. Firmly depress the brake pedal with your left foot.

  1. Move the shift lever to D.

  1. Record each battery block voltage from the Data List "Battery Block Vol -V01 to V14" while fully depressing the accelerator pedal.



  1. Compare the battery block voltages "Battery Block Vol -V01 to V14" between the even and odd number groups in each combination shown in the table below.

    Table 1:

    Circuit A Battery Block
    Circuit B Battery Block
    Condition
    Battery Block Vol - V01 (VB1)
    Battery Block Vol - V02 (VB2)
    "Battery Block Vol - V01" - "Battery Block Vol - V02" = 0.3 V or more
    Battery Block Vol - V04 (VB4)
    Battery Block Vol - V03 (VB3)
    "Battery Block Vol - V04" - "Battery Block Vol - V03" = 0.3 V or more
    Battery Block Vol - V05 (VB5)
    Battery Block Vol - V06 (VB6)
    "Battery Block Vol - V05" - "Battery Block Vol - V06" = 0.3 V or more
    Battery Block Vol - V08 (VB8)
    Battery Block Vol - V07 (VB7)
    "Battery Block Vol - V08" - "Battery Block Vol - V07" = 0.3 V or more
    Battery Block Vol - V09 (VB9)
    Battery Block Vol - V10 (VB10)
    "Battery Block Vol - V09" - "Battery Block Vol - V10" = 0.3 V or more
    Battery Block Vol - V12 (VB12)
    Battery Block Vol - V11 (VB11)
    "Battery Block Vol - V12" - "Battery Block Vol - V11" = 0.3 V or more
    Battery Block Vol - V13 (VB13)
    Battery Block Vol - V14 (VB14)
    "Battery Block Vol - V13" - "Battery Block Vol - V14" = 0.3 V or more


    Table 2:

    Circuit A Battery Block
    Circuit B Battery Block
    Condition
    Battery Block Vol - V01 (VB1)
    Battery Block Vol - V02 (VB2)
    "Battery Block Vol - V02" - "Battery Block Vol - V01" = 0.3 V or more
    Battery Block Vol - V04 (VB4)
    Battery Block Vol - V03 (VB3)
    "Battery Block Vol - V03" - "Battery Block Vol - V04" = 0.3 V or more
    Battery Block Vol - V05 (VB5)
    Battery Block Vol - V06 (VB6)
    "Battery Block Vol - V06" - "Battery Block Vol - V05" = 0.3 V or more
    Battery Block Vol - V08 (VB8)
    Battery Block Vol - V07 (VB7)
    "Battery Block Vol - V07" - "Battery Block Vol - V08" = 0.3 V or more
    Battery Block Vol - V09 (VB9)
    Battery Block Vol - V10 (VB10)
    "Battery Block Vol - V10" - "Battery Block Vol - V09" = 0.3 V or more
    Battery Block Vol - V12 (VB12)
    Battery Block Vol - V11 (VB11)
    "Battery Block Vol - V11" - "Battery Block Vol - V12" = 0.3 V or more
    Battery Block Vol - V13 (VB13)
    Battery Block Vol - V14 (VB14)
    "Battery Block Vol - V14" - "Battery Block Vol - V13" = 0.3 V or more


    A298784E01


    A298786E01

    HINT:
    When an internal malfunction occurs in the battery smart unit, this symptom (difference in voltage of 0.3 V or more for all 7 pairs of blocks) will occur.

    Result:
    Result
    Proceed to
    All conditions in table 1 are met.
    A
    All conditions in table 2 are met.
    Other than above
    B

  1. Turn the power switch off.



B
Go to step 3
A

REPLACE BATTERY SMART UNIT (Click here)  

3.CHECK DTC OUTPUT (DTC P3015-123 IS OUTPUT)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.
    Result 
    Result
    Proceed to
    DTC P3015-123 is output.
    A
    DTC P3015-123 is not output.
    B

  1. Turn the power switch off.



B
REPLACE HV BATTERY ASSEMBLY (Click here)
A

REPLACE SERVICE PLUG GRIP AND HV BATTERY ASSEMBLY