Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P2120-152    Throttle / Pedal Position Sensor / Switch "D" Circuit

DTC    P2121-106    Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance

DTC    P2122-104    Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input

DTC    P2123-105    Throttle / Pedal Position Sensor / Switch "D" Circuit High Input

DTC    P2125-153    Throttle / Pedal Position Sensor / Switch "E" Circuit

DTC    P2126-109    Throttle / Pedal Position Sensor / Switch "E" Circuit Range / Performance

DTC    P2127-107    Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input

DTC    P2128-108    Throttle / Pedal Position Sensor / Switch "E" Circuit High Input

DTC    P2138-110    Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation

DTC    P2138-154    Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation

for Preparation Click here


DESCRIPTION

The accelerator pedal position sensor is mounted on the accelerator pedal to detect how much the pedal is depressed. This is a non-contact sensor with hall elements. There are 2 outputs from the sensor. One is used to detect the accelerator pedal position and the other is used as a confirmation to allow the detection of a malfunction in the sensor itself. Voltage is output from the accelerator pedal position sensor to terminals VPA1 and VPA2 of the power management control ECU. This voltage varies from 0 to 5 V in accordance with the accelerator pedal position. Terminal VPA2 is primarily used to detect a malfunction in the sensor itself. The power management control ECU determines the current accelerator pedal position and controls the hybrid control system based on signals received by terminals VPA1 and VPA2.

A207280E03


DTC No.
INF Code
DTC Detection Condition
Trouble Area
P2120
152
Main sensor circuit wiring malfunction or level is not stable
Main sensor voltage is 0.4 V or less or 4.8 V or more for a certain period of time.
(Both of the following conditions are met: The main sensor voltage is 0.4 V or less for a certain period of time and 4.8 V or more for a certain period of time.)
(1 trip detection logic)
  1. Wire harness or connector
  2. Accelerator pedal assembly
  3. Power management control ECU
P2121
106
Internal error of the main sensor
Main sensor output changes rapidly (detected when there are no circuit malfunctions such as an open or short).
(1 trip detection logic)
P2122
104
Open or short to GND in the main sensor circuit
The main sensor voltage is 0.4 V or less for 0.5 seconds.
(1 trip detection logic)
P2123
105
Short to +B in the main sensor circuit
The main sensor voltage is 4.8 V or more for 2 seconds.
(1 trip detection logic)
P2125
153
Sub sensor circuit wiring malfunction or level is not stable
When the main sensor circuit is normal, the sub sensor voltage is 1.2 V or less or 4.8 V or more for a certain period of time.
(Both of the following conditions are met: Sub sensor voltage is 1.2 V or less for a certain period of time, and the main sensor is normal and sub sensor voltage is 4.8 V or more for a certain period of time.)
(1 trip detection logic)
P2126
109
Internal error of the sub sensor
Sub sensor output changes rapidly (detected when there are no circuit malfunctions such as an open or short).
(1 trip detection logic)
P2127
107
Open or short to GND in the sub sensor circuit
The sub sensor voltage is 1.2 V or less for 0.5 seconds.
(1 trip detection logic)
P2128
108
Short to +B in the sub sensor circuit
Main sensor is normal and sub sensor voltage is 4.8 V or more for 2 seconds.
(1 trip detection logic)
P2138
110
Difference between the main sensor value and sub sensor value is large.
(1 trip detection logic)
P2138
154
Main or sub sensor circuit wiring malfunction
The difference in voltage between the main sensor and sub sensor is 0.02 V or less, or a low output malfunction continues in both the main and sub sensors for a certain period of time.
(1 trip detection logic)

Related Data List 
DTC No.
Data List
P2120-152
  1. Accel Pedal Pos #1
  2. Accel Pedal Pos #2
P2121-106
P2122-104
P2123-105
P2125-153
P2126-109
P2127-107
P2128-108
P2138-110
P2138-154

WIRING DIAGRAM


A169668E09


INSPECTION PROCEDURE

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Wait for approximately 10 seconds with the power switch on (READY) and park (P) selected, then fully depress and release the accelerator pedal several times.

1.PERFORM ACTIVE TEST USING TECHSTREAM (ACCEL PEDAL POS #1, ACCEL PEDAL POS #2)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Accel Pedal Pos #1, Accel Pedal Pos #2.



    A207281E01
  1. Read the Data List.

    Result:
    Tester Display
    Accelerator Pedal Condition
    Specified Condition
    Accel Pedal Pos #1
    Not depressed
    8 to 28% (0.4 to 1.4 V)
    Fully depressed
    62 to 92% (3.1 to 4.6 V)
    Not depressed → Fully depressed → Not depressed (Accelerator pedal should be operated slowly)
    Value changes progressively as shown in the illustration
    Accel Pedal Pos #2
    Not depressed
    20 to 44% (1.0 to 2.2 V)
    Fully depressed
    78 to 100% (3.9 to 5.0 V)
    Not depressed → Fully depressed → Not depressed (Accelerator pedal should be operated slowly)
    Value changes progressively as shown in the illustration

    Text in Illustration 
    *1
    Accelerator Pedal Position Sensor Output Voltage (V)
    *2
    Accelerator Pedal Fully Released
    *3
    Accelerator Pedal Fully depressed
    *4
    Accelerator Pedal Turning Angle (°)

    HINT:
    5 V is described as 100% on the tester.

  1. Turn the power switch off.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL ASSEMBLY CONNECTOR)


    A215637E01
  1. Check the connection of the accelerator pedal assembly connector A29.

    OK:
    The connector is connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


3.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)


    A216617
  1. Check the connections of the power management control ECU connectors.

    OK:
    The connectors are connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


4.CHECK POWER MANAGEMENT CONTROL ECU (CHECK VOLTAGE)
  1. Disconnect connector A29 from the accelerator pedal assembly.

  1. Turn the power switch on (IG).



    A218062E03
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage :
    Tester Connection
    Switch Condition
    Specified Condition
    A29-4 (VCP1) - A29-5 (EP1)
    Power switch on (IG)
    4.5 to 5.5 V
    A29-1 (VCP2) - A29-2 (EP2)
    Power switch on (IG)
    4.5 to 5.5 V

Text in Illustration 
*1
Front view of wire harness connector:
(to Accelerator Pedal Assembly)
  1. Connect the accelerator pedal assembly connector.

  1. Turn the power switch off.



NG
Go to step 7
OK


5.CHECK POWER MANAGEMENT CONTROL ECU (CHECK RESISTANCE)
  1. Disconnect connector A29 from the accelerator pedal assembly.



    A218062E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A29-6 (VPA1) - A29-5 (EP1)
    Power switch off
    36.60 to 41.61 kΩ
    A29-3 (VPA2) - A29-2 (EP2)
    Power switch off
    36.60 to 41.61 kΩ

Text in Illustration 
*1
Front view of wire harness connector:
(to Accelerator Pedal Assembly)
  1. Connect the accelerator pedal assembly connector.



NG
Go to step 6
OK

REPLACE ACCELERATOR PEDAL ASSEMBLY (Click here)  

6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ACCELERATOR PEDAL ASSEMBLY)
  1. Disconnect connector A29 from the accelerator pedal assembly.



    A218011E03
  1. Disconnect connector A22 from the power management control ECU.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage :
    Tester Connection
    Switch Condition
    Specified Condition
    A22-26 (VPA1) - Body ground
    Power switch on (IG)
    Below 1 V
    A22-27 (VPA2) - Body ground
    Power switch on (IG)
    Below 1 V
    A22-34 (EP1) - Body ground
    Power switch on (IG)
    Below 1 V
    A22-35 (EP2) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *1
    Rear view of wire harness connector:
    (to Power Management Control ECU)
    *2
    Front view of wire harness connector:
    (to Accelerator Pedal Assembly)

    NOTICE:
    Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    A22-26 (VPA1) - A29-6 (VPA1)
    Power switch off
    Below 1 Ω
    A22-34 (EP1) - A29-5 (EP1)
    Power switch off
    Below 1 Ω
    A22-27 (VPA2) - A29-3 (VPA2)
    Power switch off
    Below 1 Ω
    A22-35 (EP2) - A29-2 (EP2)
    Power switch off
    Below 1 Ω

    Standard Resistance (Check for short):
    Tester Connection
    Switch Condition
    Specified Condition
    A22-26 (VPA1) or A29-6 (VPA1) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A22-34 (EP1) or A29-5 (EP1) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A22-27 (VPA2) or A29-3 (VPA2) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A22-35 (EP2) or A29-2 (EP2) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

  1. Connect the power management control ECU connector.

  1. Connect the accelerator pedal assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ACCELERATOR PEDAL ASSEMBLY)
  1. Disconnect connector A29 from the accelerator pedal assembly.

  1. Disconnect connector A22 from the power management control ECU.

  1. Turn the power switch on (IG).



    A218011E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage :
    Tester Connection
    Switch Condition
    Specified Condition
    A22-18 (VCP1) - Body ground
    Power switch on (IG)
    Below 1 V
    A22-34 (EP1) - Body ground
    Power switch on (IG)
    Below 1 V
    A22-19 (VCP2) - Body ground
    Power switch on (IG)
    Below 1 V
    A22-35 (EP2) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *1
    Rear view of wire harness connector:
    (to Power Management Control ECU)
    *2
    Front view of wire harness connector:
    (to Accelerator Pedal Assembly)

    NOTICE:
    Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    A22-18 (VCP1) - A29-4 (VCP1)
    Power switch off
    Below 1 Ω
    A22-34 (EP1) - A29-5 (EP1)
    Power switch off
    Below 1 Ω
    A22-19 (VCP2) - A29-1 (VCP2)
    Power switch off
    Below 1 Ω
    A22-35 (EP2) - A29-2 (EP2)
    Power switch off
    Below 1 Ω

    Standard Resistance (Check for short):
    Tester Connection
    Switch Condition
    Specified Condition
    A22-18 (VCP1) or A29-4 (VCP1) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A22-34 (EP1) or A29-5 (EP1) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A22-19 (VCP2) or A29-1 (VCP2) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A22-35 (EP2) or A29-2 (EP2) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

  1. Connect the power management control ECU connector.

  1. Connect the accelerator pedal assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)