Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM (for Brushless Type Motor)

POWER STEERING SYSTEM (for Brushless Type Motor) > TERMINALS OF ECU

for Preparation Click here



CHECK POWER STEERING ECU

C136844E09


Text in Illustration 
*1
Component without harness connected
(Power Steering ECU)

HINT:
As connector z16 uses a lock lever, each terminal cannot be checked while the connector is still connected to the power steering ECU.


Terminal No. (Symbols)
Wiring Color
Terminal Description
z16-1 (V)
W
V phase motor output
z16-2 (U)
B
U phase motor output
z16-3 (W)
R
W phase motor output
  1. Measure the voltage and resistance according to the value(s) in the table below.

    NOTICE:
    When the P/S warning light is illuminated during a malfunction, the fail-safe function may cause the voltage of the power steering ECU terminals to become 0 V.


    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A27-1 (PIG) - A27-2 (PGND)
    W - W-B
    Power source
    Always
    11 to 14 V
    A27-2 (PGND) - Body ground
    W-B - Body ground
    Power ground
    Always
    Below 1 Ω
    L54-1 (CANH) - L54-7 (CANL)
    R - W
    CAN communication line
    Power switch off
    54 to 69 Ω
    L54-6 (IG) - A27-2 (PGND)
    B - W-B
    IG power source
    Power switch on (IG)
    11 to 14 V
    z15-1 (RZV) - A27-2 (PGND)
    R - W-B
    Rotation angle sensor excitation output signal
    Power switch on (READY)
    Steering wheel turned
    0.68 to 4.42 V
    z15-3 (RZG) - A27-2 (PGND)
    B - W-B
    Rotation angle sensor excitation circuit GND
    Always
    Below 1 Ω
    z15-5 (RZCS) - A27-2 (PGND)
    L - W-B
    Rotation angle sensor COS aspect output signal
    Power switch on (READY)
    Steering wheel turned
    0.68 to 4.42 V
    z15-6 (RZSN) - A27-2 (PGND)
    Y - W-B
    Rotation angle sensor SIN aspect output signal
    Power switch on (READY)
    Steering wheel turned
    0.68 to 4.42 V
    z14-5 (TRQ1) - z14-8 (TRQG)
    -
    Torque sensor signal
    Power switch on (READY)
    Steering wheel not turned (without load)
    2.3 to 2.7 V
    Power switch on (READY)
    Steering wheel turned to right with vehicle stopped
    2.5 to 3.8 V
    Power switch on (READY)
    Steering wheel turned to left with vehicle stopped
    1.2 to 2.5 V
    z14-6 (TRQV) - z14-8 (TRQG)
    -
    Torque sensor voltage source
    Power switch on (IG)
    4.5 to 5.5 V
    z14-7 (TRQ2) - z14-8 (TRQG)
    -
    Torque sensor signal
    Power switch on (READY)
    Steering wheel not turned (without load)
    2.3 to 2.7 V
    Power switch on (READY)
    Steering wheel turned to right with vehicle stopped
    1.2 to 2.5 V
    Power switch on (READY)
    Steering wheel turned to left with vehicle stopped
    2.5 to 3.8 V
    z14-8 (TRQG) - Body ground
    - Body ground
    Torque sensor ground
    Always
    Below 1 Ω
    If the result is not as specified, the ECU may have a malfunction.