POWER STEERING SYSTEM (for Brushless Type Motor) > DATA LIST / ACTIVE TEST |
| DATA LIST |
Turn the power switch off.
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Chassis / EMPS / Data List.
According to the display on the Techstream, read the "Data List".
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Meter Vehicle Velocity | Vehicle speed from meter/ Min.: 0 km/h (0 mph) Max.: 300 km/h (186.4 mph) | 0 km/h (0 mph) | Power switch on (READY) and vehicle stopped |
| No significant fluctuation | Power switch on (READY) and vehicle driven at a constant speed | ||
| Motor Actual Current | Amount of current to motor/ Min.: -327.68 A Max.: 327.67 A | Value changes in proportion to steering effort | Power switch on (READY) and power steering is in operation |
| Command Value Current | Demanded amount of current to motor/ Min.: -327.68 A Max.: 327.67 A | Value changes in proportion to steering effort | Power switch on (READY) and power steering is in operation |
| Steering Angle Velocity | Steering angle speed/ Min.: -32768 deg/s Max.: 32767 deg/s | Value changes in proportion to steering effort | Power switch on (READY) and steering wheel is turned |
| Thermistor Temperature | ECU substrate temperature/ Min.: -40°C (-40°F) Max.: 150°C (302°F) | -40°C to 150°C (-40°F to 302°F) | Power switch on (READY) |
| PIG Power Supply | Power source voltage to active motor/ Min.: 0 V Max.: 20.1531 V | 11 to 14 V | Power switch on (READY) and power steering is in operation |
| IG Power Supply | ECU power source voltage/ Min.: 0 V Max.: 20.1531 V | 11 to 14 V | Power switch on (IG) |
| Steering Angle Sens Sig | Steering angle sensor signal state/ OK or NG(1) or NG(2) or NG(3) | OK: Steering angle sensor signal is received NG(1): The learning has not completed NG(2): Steering Sensor Abnormal NG(3): Communication Error | - |
| Steering Wheel Torque | Steering wheel torque/ Min.: -327.68 Nm Max.: 7 Nm | Value changes in proportion to steering effort | Power switch on (READY) and power steering is in operation |
| Motor Rotation Angle | Motor rotation angle/ Min.: 0 deg Max.: 1441.77 deg | During steering operation, motor rotation angle value changes from 0 to 360° | Power switch on (READY) and power steering is in operation |
| Command Val Current 2 | Demanded amount of current to motor/ Min.: -327.68 A Max.: 327.67 A | Value changes in proportion to steering effort | Power switch on (READY) and power steering is in operation |
| PIG2 Voltage | Coil rear pressurization voltage/ Min.: 0 V Max.: 45.955 V | Approximately 27 V | Power switch on (READY) and steering wheel is not turned |
| Value changes within 4 to 35 V range | Power switch on (READY) and steering wheel is turned | ||
| Motor Voltage | Motor power supply voltage/ Min.: 0 V Max.: 45.955 V | Approximately 27 V | Power switch on (READY) and steering wheel is not turned |
| Value changes within 4 to 35 V range | Power switch on (READY) and steering wheel is turned | ||
| Motor Terminal Volt (U) | Motor terminal voltage (U phase)/ Min.: 0 V Max.: 46.667 V | Value changes within 4 to 35 V range | Power switch on (READY) and steering wheel is turned |
| Motor Terminal Volt (V) | Motor terminal voltage (V phase)/ Min.: 0 V Max.: 46.667 V | Value changes within 4 to 35 V range | Power switch on (READY) and steering wheel is turned |
| Motor Terminal Volt (W) | Motor terminal voltage (W phase)/ Min.: 0 V Max.: 46.667 V | Value changes within 4 to 35 V range | Power switch on (READY) and steering wheel is turned |
| Torque Sensor 1 Output | Torque sensor voltage/ Min.: 0 V Max.: 5 V | 2.3 to 2.7 V | Power switch on (READY) and steering wheel is not turned (without load) |
| 2.5 to 3.8 V | Power switch on (READY) and steering wheel turned to right with vehicle stopped | ||
| 1.2 to 2.5 V | Power switch on (READY) and steering wheel turned to left with vehicle stopped | ||
| Torque Sensor 2 Output | Torque sensor voltage/ Min.: 0 V Max.: 5 V | 2.3 to 2.7 V | Power switch on (READY) and steering wheel is not turned (without load) |
| 1.2 to 2.5 V | Power switch on (READY) and steering wheel turned to right with vehicle stopped | ||
| 2.5 to 3.8 V | Power switch on (READY) and steering wheel turned to left with vehicle stopped | ||
| TRQ1 Zero Point Value | Torque sensor voltage/ Min.: 0 V Max.: 5 V | Values differ depending on vehicle | Power switch on (READY) and steering wheel is not turned |
| TRQ2 Zero Point Value | Torque sensor voltage/ Min.: 0 V Max.: 5 V | Values differ depending on vehicle | Power switch on (READY) and steering wheel is not turned |
| IG ON/OFF Times | Number of times of power switch ON/OFF after fail detection/ Min.: 0 time Max.: 65535 times | - | This value indicates the number of times of IG ON/OFF after the latest DTC detection. |
| Motor Overheat Record | Continuous overheat prevention control record/ Unrec or Rec | Unrec | - |
| Motor Lo Power Record | PIG power source voltage drop record/ Unrec or Rec | Unrec | - |
| Eng Rev Inter Record | Record of READY ON signal interruption/ Unrec or Rec | Unrec | - |
| Str Angle Inter Record | Record of steering sensor signal interruption occurrence display/ Unrec or Rec | Unrec | - |
| Spd Sig Invalid Record | Record of vehicle speed signal invalid/ Unrec or Rec | Unrec | - |
| Battery Voltage Lo Record | Auxiliary battery voltage reduction history/ Min.: 0 times, Max.: 65535 times | 0 to 65535 | - |
| Ready Status | Ready status/ READY or OFF | READY or OFF | - |
| The Number of DTCs | Number of detected DTCs when freeze frame data stored/ Min.: 0 Max.: 255 | 0 to 255 | - |