Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM (for Brushless Type Motor)

POWER STEERING SYSTEM (for Brushless Type Motor) > FREEZE FRAME DATA

for Preparation Click here



FREEZE FRAME DATA

NOTICE:
  1. It is difficult to show the specified values (judgment values) clearly because freeze frame data values change significantly due to differences in measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specifications.
  2. Turn the power switch on (IG) and park the vehicle on level ground. Check the freeze frame data by using the Techstream.

  1. Turn the power switch off.

  2. Connect the Techstream to the DLC3.

  3. Turn the power switch on (IG).

  4. Turn the Techstream on.

  5. Check the freeze frame data on the Techstream.

    EMPS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Meter Vehicle Velocity
    Vehicle speed from meter/
    Min.: 0 km/h (0 mph)
    Max.: 300 km/h (186.4 mph)
    0 km/h (0 mph)
    Power switch on (READY) and vehicle stopped
    No significant fluctuation
    Power switch on (READY) and vehicle driven at a constant speed
    Motor Actual Current
    Amount of current to motor/
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    Power switch on (READY) and power steering is in operation
    Command Value Current
    Demanded amount of current to motor/
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    Power switch on (READY) and power steering is in operation
    Steering Angle Velocity
    Steering angle speed/
    Min.: -32768 deg/s
    Max.: 32767 deg/s
    Value changes in proportion to steering effort
    Power switch on (READY) and steering wheel is turned
    Thermistor Temperature
    ECU substrate temperature/
    Min.: -40°C (-40°F)
    Max.: 150°C (302°F)
    -40°C to 150°C (-40°F to 302°F)
    Power switch on (READY)
    PIG Power Supply
    Power source voltage to active motor/
    Min.: 0 V
    Max.: 20.1531 V
    11 to 14 V
    Power switch on (READY) and power steering is in operation
    IG Power Supply
    ECU power source voltage/
    Min.: 0 V
    Max.: 20.1531 V
    11 to 14 V
    Power switch on (IG)
    Steering Wheel Torque
    Steering wheel torque/
    Min.: -327.68 Nm
    Max.: 7 Nm
    Value changes in proportion to steering effort
    Power switch on (READY) and power steering is in operation
    Motor Rotation Angle
    Motor rotation angle/
    Min.: 0 deg
    Max.: 1441.77 deg
    During steering operation, motor rotation angle value changes from 0 to 360°
    Power switch on (READY) and power steering is in operation
    Command Val Current 2
    Demanded amount of current to motor/
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    Power switch on (READY) and power steering is in operation
    PIG2 Voltage
    Coil rear pressurization voltage/
    Min.: 0 V
    Max.: 45.955 V
    Approximately 27 V
    Power switch on (READY) and steering wheel is not turned
    Value changes within 4 to 35 V range
    Power switch on (READY) and steering wheel is turned
    Motor Voltage
    Motor power supply voltage/
    Min.: 0 V
    Max.: 45.955 V
    Approximately 27 V
    Power switch on (READY) and steering wheel is not turned
    Value changes within 4 to 35 V range
    Power switch on (READY) and steering wheel is turned
    Motor Terminal Volt (U)
    Motor terminal voltage (U phase)/
    Min.: 0 V
    Max.: 46.667 V
    Value changes within 4 to 35 V range
    Power switch on (READY) and steering wheel is turned
    Motor Terminal Volt (V)
    Motor terminal voltage (V phase)/
    Min.: 0 V
    Max.: 46.667 V
    Value changes within 4 to 35 V range
    Power switch on (READY) and steering wheel is turned
    Motor Terminal Volt (W)
    Motor terminal voltage (W phase)/
    Min.: 0 V
    Max.: 46.667 V
    Value changes within 4 to 35 V range
    Power switch on (READY) and steering wheel is turned
    Torque Sensor 1 Output
    Torque sensor voltage/
    Min.: 0 V
    Max.: 5 V
    2.3 to 2.7 V
    Power switch on (READY) and steering wheel is not turned (without load)
    2.5 to 3.8 V
    Power switch on (READY) and steering wheel turned to right with vehicle stopped
    1.2 to 2.5 V
    Power switch on (READY) and steering wheel turned to left with vehicle stopped
    Torque Sensor 2 Output
    Torque sensor voltage/
    Min.: 0 V
    Max.: 5 V
    2.3 to 2.7 V
    Power switch on (READY) and steering wheel is not turned (without load)
    1.2 to 2.5 V
    Power switch on (READY) and steering wheel turned to right with vehicle stopped
    2.5 to 3.8 V
    Power switch on (READY) and steering wheel turned to left with vehicle stopped
    TRQ1 Zero Point Value
    Torque sensor voltage/
    Min.: 0 V
    Max.: 5 V
    Values differ depending on vehicle
    Power switch on (READY) and steering wheel is not turned
    TRQ2 Zero Point Value
    Torque sensor voltage/
    Min.: 0 V
    Max.: 5 V
    Values differ depending on vehicle
    Power switch on (READY) and steering wheel is not turned
    Ready Status
    Ready status/
    READY or OFF
    READY or OFF
    -