Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM (for Brush Type Motor)

POWER STEERING SYSTEM (for Brush Type Motor) > FREEZE FRAME DATA

for Preparation Click here



FREEZE FRAME DATA

NOTICE:
  1. Freeze frame data values will vary depending on the measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even if the values are within specifications.
  2. Turn the power switch on (IG) and park the vehicle on level ground. Check the freeze frame data by using the Techstream.

  1. Turn the power switch off.

  2. Connect the Techstream to the DLC3.

  3. Turn the power switch on (IG).

  4. Turn the Techstream on.

  5. Check the freeze frame data on the Techstream.

    EMPS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Meter Vehicle Velocity
    Vehicle speed from meter/
    Min.: 0 km/h (mph)
    Max.: 300 km/h (186.4 mph)
    0 km/h (0 mph)
    Turn the power switch on (READY) and vehicle stopped
    No significant fluctuation
    Turn the power switch on (READY) and vehicle driven at constant speed
    Motor Actual Current
    Current to motor/
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    Turn the power switch on (READY) and power steering is in operation
    Command Value Current
    Requested current to motor/
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    Turn the power switch on (READY) and power steering is in operation
    Thermistor Temperature
    ECU substrate temperature/
    Min.: -40°C (-40°F)
    Max.: 150°C (302°F)
    -40 to 150°C (-40 to 302°F)
    -
    PIG Power Supply
    Power source voltage to activate motor/
    Min.: 0 V
    Max.: 20.1531 V
    11 to 14 V
    Power switch on (READY)
    IG Power Supply
    ECU power source voltage/
    Min.: 0 V
    Max.: 20.1531 V
    11 to 14 V
    Power switch on (READY)
    Steering Wheel Torque
    Steering wheel torque/
    Min.: -327.68 Nm
    Max.: 7 Nm
    Value changes in proportion to steering effort
    Power switch on (READY) and power steering is in operation
    Torque Sensor 1 Output
    Torque sensor 1 output value/
    Min.: 0 V
    Max.: 5 V
    2.3 to 2.7 V
    Turn the power switch on (READY) and steering wheel not turned (without load)
    2.5 to 3.8 V
    Turn the power switch on (READY) and steering wheel turned to right with vehicle stopped
    1.2 to 2.5 V
    Turn the power switch on (READY) and steering wheel turned to left with vehicle stopped
    Torque Sensor 2 Output
    Torque sensor 2 output value/
    Min.: 0 V
    Max.: 5 V
    2.3 to 2.7 V
    Turn the power switch on (READY) and steering wheel not turned (without load)
    1.2 to 2.5 V
    Turn the power switch on (READY) and steering wheel turned to right with vehicle stopped
    2.5 to 3.8 V
    Turn the power switch on (READY) and steering wheel turned to left with vehicle stopped
    TRQ1 Zero Point Value
    Zero point value of torque sensor 1/
    Min.: 0 V
    Max.: 5 V
    2.3 to 2.7 V
    Turn the power switch on (READY) and steering wheel not turned (without load)
    TRQ2 Zero Point Value
    Zero point value of torque sensor 2/
    Min.: 0 V
    Max.: 5 V
    2.3 to 2.7 V
    Turn the power switch on (READY) and steering wheel not turned (without load)
    Motor Terminal Volt(+)
    Motor terminal M1 voltage/
    Min.: 0 V
    Max.: 25.5 V
    11 to 14 V
    Turn the power switch on (READY) and steering wheel turned to right
    Below 1 V
    Turn the power switch on (READY) and steering wheel turned to left
    Motor Terminal Volt(-)
    Motor terminal M2 voltage/
    Min.: 0 V
    Max.: 25.5 V
    Below 1 V
    Turn the power switch on (READY) and steering wheel turned to right
    11 to 14 V
    Turn the power switch on (READY) and steering wheel turned to left
    Ready Status
    Ready status/
    READY or OFF
    READY or OFF
    -