Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P0A9D-123    Hybrid Battery Temperature Sensor "A" Circuit Low

DTC    P0A9E-123    Hybrid Battery Temperature Sensor "A" Circuit High

DTC    P0AC7-123    Hybrid Battery Temperature Sensor "B" Circuit Low

DTC    P0AC8-123    Hybrid Battery Temperature Sensor "B" Circuit High

DTC    P0ACC-123    Hybrid Battery Temperature Sensor "C" Circuit Low

DTC    P0ACD-123    Hybrid Battery Temperature Sensor "C" Circuit High

for Preparation Click here


DESCRIPTION

  1. Refer to the description for DTC P0A9C-123 .

DTC No.
DTC Detection Condition
Trouble Area
P0A9D-123
P0AC7-123
P0ACC-123
The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
  1. Hybrid battery thermistor
  2. Battery smart unit
  3. Wire harness or connector
  4. Hybrid battery junction block
P0A9E-123
P0AC8-123
P0ACD-123
The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)

HINT:
After confirming that a DTC is output, use the Techstream to check "Temp of BATT TB 1 to 3" in the hybrid vehicle control system ECU data list.

Temperature Displayed
Malfunction
Below -49°F (-45°C)
Open or +B short circuit
203°F (95°C) or more
GND short circuit

Related Data List 
DTC No.
Data List
P0A9D-123
P0A9E-123
P0AC7-123
P0AC8-123
P0ACC-123
P0ACD-123
Temp of Batt TB1 to TB3

MONITOR DESCRIPTION

If the temperature indicated by the battery temperature sensor is lower than the standard level (open), or is higher than the standard level (short), the battery smart unit interprets this as a sensor malfunction. If the battery smart unit detects that HV battery temperature is out of the normal range or its value is abnormal, the power management control ECU (HV CPU) will illuminate the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0A9D (INF 123): Battery temperature sensor circuit malfunction (GND short)
P0A9E (INF 123): Battery temperature sensor circuit malfunction (open)
P0AC7 (INF 123): Battery temperature sensor circuit malfunction (GND short)
P0AC8 (INF 123): Battery temperature sensor circuit malfunction (open)
P0ACC (INF 123): Battery temperature sensor circuit malfunction (GND short)
P0ACD (INF 123): Battery temperature sensor circuit malfunction (open)
Required sensors / components
Battery temperature sensor
Frequency of operation
Continuous
Duration
TMC's intellectual property
MIL operation
TMC's intellectual property
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TMC's intellectual property
Other conditions belong to TMC's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


TMC's intellectual property
-

COMPONENT OPERATING RANGE


Battery smart unit
DTC P0A9D (INF 123) is not detected
DTC P0A9E (INF 123) is not detected
DTC P0AC7 (INF 123) is not detected
DTC P0AC8 (INF 123) is not detected
DTC P0ACC (INF 123) is not detected
DTC P0ACD (INF 123) is not detected

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off.
  5. Turn the power switch on (IG) and wait for 10 seconds or more.
  6. Perform the universal trip.
  7. Enter the following menus: Powertrain / HV / Trouble Codes.
  8. Read the current DTCs.

    HINT:
    1. If a current DTC is output, the system is malfunctioning.
    2. If a current DTC is not output and want to confirm permanent DTC, perform the following procedure.

  9. Check that permanent DTCs are cleared.

WIRING DIAGRAM


A219394E06


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals.

    HINT:
    At least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

NOTICE:
After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the power switch on (IG) and wait for 10 seconds or more.

1.CHECK DTC OUTPUT (DTC P0AFC-123 IS OUTPUT)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check and record any HV system DTCs, INF codes and freeze frame data.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    P0AFC-123 is not output.
    A
    P0AFC-123 is also output.
    B

  1. Disconnect the Techstream from the DLC3.



B
GO TO DTC CHART
A


2.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Temp of Batt TB 1 to 3.

    HINT:
    Compare the temperature of the 3 battery temperature sensors to determine the sensor with the malfunction (Temp of Batt TB1 to TB3).


NEXT


3.CHECK CONNECTOR CONNECTION CONDITION

CAUTION:
Be sure to wear insulated gloves.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).



    A217836E02
  1. Check the connections of the z17 connector of the battery smart unit.

    OK:
    The connectors are connected securely and there are no contact problems.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.



NG
CONNECT SECURELY
OK


4.CHECK HYBRID BATTERY THERMISTOR (BATTERY TEMPERATURE SENSOR)

CAUTION:
Be sure to wear insulated gloves.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).



    A217836E01
  1. Disconnect connectors z17 and c1 from the battery smart unit.



    A216736E04
  1. Measure the resistance of the circuit for the malfunctioning sensor (battery temperature sensor 0 to 2).
    Tester Connection 
    Tester Connection
    Battery Temperature Sensor No.
    z17-6 (TBO) - z17-12 (GBO)
    0
    z17-5 (TB1) - z17-11 (GB1)
    1
    z17-4 (TB2) - z17-10 (GB2)
    2
    Standard Resistance 
    Thermistor Temperature
    Switch Condition
    Specified Condition
    32°F (0°C)
    Power switch off
    26.7 to 27.8 kΩ
    77°F (25°C)
    Power switch off
    9.9 to 10.1 kΩ
    104°F (40°C )
    Power switch off
    5.73 to 5.92 kΩ
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Battery Smart Unit)



    A216735E08
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Standard Resistance
    z17-6 (TBO) - c1-4 (IGCT)
    Power switch off
    10 kΩ or more
    z17-6 (TBO) - c1-8 (GND)
    Power switch off
    10 kΩ or more
    z17-12 (GBO) - c1-4 (IGCT)
    Power switch off
    10 kΩ or more
    z17-12 (GBO) - c1-8 (GND)
    Power switch off
    10 kΩ or more
    z17-5 (TB1) - c1-4 (IGCT)
    Power switch off
    10 kΩ or more
    z17-5 (TB1) - c1-8 (GND)
    Power switch off
    10 kΩ or more
    z17-11 (GB1) - c1-4 (IGCT)
    Power switch off
    10 kΩ or more
    z17-11 (GB1) - c1-8 (GND)
    Power switch off
    10 kΩ or more
    z17-4 (TB2) - c1-4 (IGCT)
    Power switch off
    10 kΩ or more
    z17-4 (TB2) - c1-8 (GND)
    Power switch off
    10 kΩ or more
    z17-10 (GB2) - c1-4 (IGCT)
    Power switch off
    10 kΩ or more
    z17-10 (GB2) - c1-8 (GND)
    Power switch off
    10 kΩ or more
    z17-1 (TCO) - c1-4 (IGCT)
    Power switch off
    10 kΩ or more
    z17-1 (TCO) - c1-8 (GND)
    Power switch off
    10 kΩ or more
    z17-7 (GCO) - c1-4 (IGCT)
    Power switch off
    10 kΩ or more
    z17-7 (GCO) - c1-8 (GND)
    Power switch off
    10 kΩ or more

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Battery Smart Unit)

  1. Connect the battery smart unit connectors.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.



NG
Go to step 8
OK


5.CHECK BATTERY SMART UNIT (VIB VOLTAGE)

NOTICE:
Be sure to wear insulated gloves.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the power switch on (IG).

    NOTICE:
    Turning the power switch on (IG) with the service plug grip removed causes an interlock switch system DTC (P0A0D-350) to be set. Use the Techstream to clear the DTCs (Click here).



    A214447E08
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    c1-5 (VIB) - c1-6 (GIB)
    Power switch on (IG)
    4.6 to 5.4 V

    Text in Illustration 
    *a
    Component with harness connected
    (Battery Smart Unit)

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.



NG
Go to step 6
OK

REPLACE BATTERY SMART UNIT (Click here)  

6.CHECK HYBRID BATTERY JUNCTION BLOCK

NOTICE:
Be sure to wear insulated gloves.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Disconnect the c4 battery current sensor connector from the hybrid battery junction block.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the power switch on (IG).

    NOTICE:
    Turning the power switch on (IG) with the HV relay assembly (battery current sensor) connector disconnected causes DTC P0AC2-123 to be set. Use the Techstream to clear the DTCs (Click here).



    A221326E04
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    c4-1 (VIB) - c4-2 (GIB)
    Power switch on (IG)
    4.6 to 5.4 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Hybrid Battery Junction Block)

  1. Turn the power switch off.

  1. Connect the c4 battery current sensor connector to the hybrid battery junction block.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).



NG
Go to step 7
OK

REPLACE HYBRID BATTERY JUNCTION BLOCK (Click here)  

7.CHECK HARNESS AND CONNECTOR (BATTERY SMART UNIT - HYBRID BATTERY JUNCTION BLOCK)

NOTICE:
Be sure to wear insulated gloves.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).



    A217836E03
  1. Disconnect only the c1 connector of the battery smart unit.

  1. Disconnect the c4 battery current sensor connector from the hybrid battery junction block.



    A221325E03
  1. Measure the resistance according to the value(s) in the tables below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    c1-1 (IB) - c4-3 (IB)
    Power switch off
    Below 1 Ω
    c1-6 (GIB) - c4-2 (GIB)
    Power switch off
    Below 1 Ω
    c1-5 (VIB) - c4-1 (VIB)
    Power switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    c1-1 (IB) or c4-3 (IB) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    c1-6 (GIB) or c4-2 (GIB) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    c1-5 (VIB) or c4-1 (VIB) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Battery Smart Unit)
    *b
    Front view of wire harness connector
    (to Hybrid Battery Junction Block)

  1. Connect the battery smart unit connector.

  1. Connect the c4 battery current sensor connector to the hybrid battery junction block.

  1. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BATTERY SMART UNIT (Click here)  

8.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR)

CAUTION:
Be sure to wear insulated gloves and protective goggles.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the upper hybrid battery cover sub-assembly (Click here).

  1. Check the wire harness and connectors of the battery temperature sensor for abnormalities by sight and touch.

    Specified Condition:
    There are no open or short circuits in the wire harness and connectors. There are no short circuits to other wire harnesses.

  1. Install the upper hybrid battery cover sub-assembly (Click here).

  1. Connect the cable to the negative (-) battery terminal.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID BATTERY THERMISTOR (Click here)