Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A10-592    DC / DC Converter Status Circuit High Input

for Preparation Click here


DESCRIPTION

Refer to the description for DTC P0A09-591 .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A10
592
Short to +B in the DC/DC converter VLO signal line
(1 trip detection logic)
  1. Wire harness or connector
  2. Inverter with converter assembly
  3. Power management control ECU

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A09-591 .

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

    HINT:
    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the power switch on (IG) and wait for 10 seconds or more.

1.CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)
  1. Turn the power switch on (IG).



    A204482E02
  1. Connect an oscilloscope between the power management control ECU terminals specified in the table below, and measure the waveform.
    Item
    Content
    Terminal
    A21-11 (VLO) - L5-6 (E1)
    Equipment Setting
    5V/DIV., 50ms/DIV.
    Condition
    Power switch on (IG)
    Text in Illustration 
    *1
    Component with harness connected
    (Power Management Control ECU)

    OK:
    The waveform appears as shown in the illustration.

    HINT:
    1. Perform this inspection with the power management control ECU connector connected.
    2. The waveform varies depending on the specified DC/DC converter voltage.

  1. Turn the power switch off.



NG
Go to step 4
OK


2.CLEAR DTC
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Clear DTCs and freeze frame data.


NEXT


3.CHECK DTC OUTPUT (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    DTC P0A10-592 is not output.
    A
    DTC P0A10-592 is output again.
    B

  1. Turn the power switch off.



B
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER - POWER MANAGEMENT CONTROL ECU)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector A59 from the inverter with converter assembly.

  1. Disconnect connector A21 from the power management control ECU.

  1. Turn the power switch on (IG).



    A216618E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A59-3 (VLO) or A21-11 (VLO) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Inverter with Converter Assembly)
    *2
    Rear view of wire harness connector
    (to Power Management Control ECU)

    NOTICE:
    Turning the power switch on (IG) with the inverter with converter assembly connector and the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Connect the inverter with converter assembly connector.

  1. Connect the power management control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE POWER MANAGEMENT CONTROL ECU
  1. Replace the power management control ECU (Click here).


NEXT


6.CLEAR DTC
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Clear DTCs and freeze frame data.


NEXT


7.CHECK DTC OUTPUT (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    DTC P0A10-592 is not output.
    A
    DTC P0A10-592 is output again.
    B

  1. Turn the power switch off.



B
REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)
A

COMPLETED