Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

DTC    U1002    Lost Communication with Gateway Module (Power Management1)

for Preparation Click here


DESCRIPTION

  1. The power management control ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to the CAN No. 2 bus.
  2. When the power management control ECU receives a response signal from the ECUs connected to the CAN No. 2 bus, the power management control ECU recognizes and memorizes that the ECU is connected to the CAN No. 2 bus. Based on this memorized data, the power management control ECU monitors for malfunctions in the ECUs connected to the CAN No. 2 bus when communicating with those ECUs. If the power management control ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN No. 2 bus, the power management control ECU determines that a malfunction exists.

DTC No.
DTC Detection Condition
Trouble Area
U1002
Power management control ECU cannot receive signals from all ECUs that have been memorized as those connected to the CAN No. 2 bus.
  1. Open or short in CAN No. 2 bus main wire or connector
  2. Open or short in CAN No. 2 bus branch wire or connector
  3. Power management control ECU
  4. Driving support ECU
  5. Seat belt control ECU
  6. CAN No. 3 junction connector

HINT:
The diagnosis procedure is for when DTC U1002 is output by the power management control ECU (Techstream display: Power Management1).


WIRING DIAGRAM


C252718E01


INSPECTION PROCEDURE

NOTICE:
  1. Turn the power switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
  2. Turn the power switch off before inspecting CAN bus wires for a ground short.
  3. After the power switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
  4. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the power switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.CHECK CAN NO. 2 BUS WIRE
  1. Turn the power switch off.



    A204441E21
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Result
    L5-34 (CA2H) - L5-35 (CA2L)
    Power switch off
    54 to 69 Ω
    Below 54 Ω:
    Short circuit between bus lines
    70 Ω or higher:
    Open circuit in a main bus line
    L5-34 (CA2H) - L5-6 (E1)
    Power switch off
    200 Ω or higher
    Below 200 Ω:
    CANH ground short
    L5-35 (CA2L) - L5-6 (E1)
    Power switch off
    200 Ω or higher
    Below 200 Ω:
    CANL ground short

    Text in Illustration 
    *1
    Component with harness connected
    (Power Management Control ECU)

  1. Disconnected the cable from the negative (-) auxiliary battery terminal.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Result
    L5-34 (CA2H) - L5-1 (AM22)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Below 6 kΩ:
    CANH +B short
    L5-35 (CA2L) - L5-1 (AM22)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Below 6 kΩ:
    CANL +B short

    Result:
    Result
    Proceed to
    OK
    A
    Open circuit in CAN main bus line
    B
    Short circuit between bus lines
    C
    1. Ground short
    2. +B short
    D



B
Go to step 3

C
Go to step 5

D
Go to step 9
A


2.CHECK DTC OUTPUT
  1. Clear the DTC.

  1. Turn the power switch off.

  1. Turn the power switch on (IG), recheck the DTC.

    Result:
    Result
    Proceed to
    U1002 is output from power management control ECU
    (Techstream display/ Power Management1)
    A
    Other DTC is output
    B



B
GO TO CIRCUITS INDICATED BY OUTPUT DTCS
A

REPLACE POWER MANAGEMENT CONTROL ECU 

3.CHECK FOR OPEN IN CAN NO. 2 BUS MAIN WIRE (POWER MANAGEMENT CONTROL ECU MAIN WIRE)


    A204445E03
  1. Disconnect the power management control ECU connector.
    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to Power Management Control ECU)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L5-34 (CA2H) - L5-35 (CA2L)
    Power switch off
    108 to 132 Ω



NG
Go to step 4
OK

REPLACE POWER MANAGEMENT CONTROL ECU 

4.CHECK FOR OPEN IN CAN NO. 2 BUS MAIN WIRE (CAN NO. 3 J/C)
  1. Reconnect the power management control ECU connector.



    C216833E01
  1. Disconnect the power management control ECU main wire connector from the CAN No. 3 junction connector.
    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to CAN No. 3 Junction Connector)
    *2
    to Power Management Control ECU

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Connected to
    L97-1 (CANH) - L97-2 (CANL)
    Power switch off
    108 to 132 Ω
    Power management control ECU



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - POWER MANAGEMENT CONTROL ECU)
OK

REPLACE CAN NO. 3 JUNCTION CONNECTOR 

5.CHECK FOR SHORT IN CAN NO. 2 BUS WIRE (POWER MANAGEMENT CONTROL ECU)


    A204445E03
  1. Disconnect the power management control ECU connector.
    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to Power Management Control ECU)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L5-34 (CA2H) - L5-35 (CA2L)
    Power switch off
    108 to 132 Ω



NG
Go to step 6
OK

REPLACE POWER MANAGEMENT CONTROL ECU 

6.CHECK FOR SHORT IN CAN NO. 2 BUS WIRE (CAN NO. 3 J/C - POWER MANAGEMENT CONTROL ECU)
  1. Reconnect the power management control ECU connector.



    C216833E01
  1. Disconnect the power management control ECU main wire connector from the CAN No. 3 junction connector.
    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to CAN No. 3 Junction Connector)
    *2
    to Power Management Control ECU

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Connected to
    L97-1 (CANH) - L97-2 (CANL)
    Power switch off
    108 to 132 Ω
    Power management control ECU



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - POWER MANAGEMENT CONTROL ECU)
OK


7.CHECK FOR SHORT IN CAN NO. 2 BUS WIRE (CAN NO. 3 J/C)
  1. Reconnect the power management control ECU main wire connector to the CAN No. 3 junction connector.



    A204441E22
  1. Connect the probes of an ohmmeter to terminals 34 (CA2H) and 35 (CA2L) of the power management control ECU.
    Text in Illustration 
    *1
    Component with harness connector
    (Power Management Control ECU)



  1. While observing the resistance value shown on the ohmmeter, disconnect branch wire connectors (except L97) from the CAN No. 3 junction connector until the resistance becomes normal (between 54 and 69 Ω).


    C252630E01


    Text in Illustration 
    *1
    CAN No. 3 Junction Connector
    *2
    Junction Connector B Side
    *3
    Junction Connector A Side
    *4
    Earth Terminal
    *5
    Front view of wire harness connector
    (to CAN No. 3 Junction Connector)
    -
    -

    Terminal No. (Symbol)
    Wiring Color
    Connected to
    L97-1 (CANH)
    P
    Power management control ECU
    L97-2 (CANL)
    V
    L98-1 (CANH)
    LG
    Seat belt control ECU
    L98-2 (CANL)
    L
    L99-1 (CANH)
    B
    Driving support ECU
    L99-2 (CANL)
    W

    HINT:
    1. The connectors connected to the CAN junction connector can be distinguished by the colors of the bus wire.
    2. Reconnecting the connectors to non-specified positions on the CAN junction connector does not affect system operation.

      Result:
      Result
      Proceed to
      The resistance is still below 54 Ω when all the specified connectors are disconnected.
      (There is no short in the branch wires.)
      A
      The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected.
      (There is a short in one or more of the branch wires.)
      B



B
Go to step 8
A

REPLACE CAN NO. 3 JUNCTION CONNECTOR 

8.CHECK FOR SHORT IN CAN NO. 2 BUS WIRE (ECUS)
  1. Reconnect the connector for the short-circuited branch wire to the CAN junction connector (the connector that caused the bus wire resistance to become normal (between 54 and 69 Ω) when it was disconnected).

  1. Disconnect the connector that includes terminals CANH and CANL from the ECU to which the short-circuited branch wire is connected.



    A204441E22
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L5-34 (CA2H) - L5-35 (CA2L)
    Power switch off
    54 to 69 Ω

    Text in Illustration 
    *1
    Component with harness connector
    (Power Management Control ECU)

    HINT:
    If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU, there may be a short in the ECU.



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH WIRE OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR 

9.CHECK FOR SHORT IN CAN NO. 2 BUS WIRE (POWER MANAGEMENT CONTROL ECU)


    A204445E02
  1. Disconnect the power management control ECU connector.
    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to Power Management Control ECU)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Purpose
    L5-34 (CA2H) - L5-6 (E1)
    Power switch off
    200 Ω or higher
    Inspection for CANH ground short
    L5-35 (CA2L) - L5-6 (E1)
    Power switch off
    200 Ω or higher
    Inspection for CANL ground short
    L5-34 (CA2H) - L5-1 (AM22)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Inspection for CANH +B short
    L5-35 (CA2L) - L5-1 (AM22)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Inspection for CANL +B short

    HINT:
    It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check CAN No. 2 Bus Wire inspection.
    Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check CAN No. 2 Bus Wire inspection.



NG
Go to step 10
OK

REPLACE POWER MANAGEMENT CONTROL ECU 

10.CHECK FOR SHORT IN CAN NO. 2 BUS WIRE (CAN NO. 3 J/C - POWER MANAGEMENT CONTROL ECU)


    C216833E01
  1. Disconnect the power management control ECU main wire connector from the CAN No. 3 junction connector.
    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to CAN No. 3 Junction Connector)
    *2
    to Power Management Control ECU



    A204445E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Purpose
    L5-34 (CA2H) - L5-6 (E1)
    Power switch off
    200 Ω or higher
    Inspection for CANH ground short
    L5-35 (CA2L) - L5-6 (E1)
    Power switch off
    200 Ω or higher
    Inspection for CANL ground short
    L5-34 (CA2H) - L5-1 (AM22)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Inspection for CANH +B short
    L5-35 (CA2L) - L5-1 (AM22)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Inspection for CANL +B short

    HINT:
    It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check CAN No. 2 Bus Wire inspection.
    Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check CAN No. 2 Bus Wire inspection.

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - POWER MANAGEMENT CONTROL ECU)
OK


11.CHECK FOR SHORT IN CAN NO. 2 BUS WIRE (CAN NO. 3 J/C)
  1. Reconnect the power management control ECU main wire connector to the CAN No. 3 junction connector.



    A204445E02
  1. Connect the probes of an ohmmeter to terminals CANH or CANL and GND or +B (AM22) of the power management control ECU.
    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to Power Management Control ECU)

    HINT:
    It is only necessary to perform the inspection for the result (short circuit) that was obtained in the Check CAN No. 2 Bus Wire inspection.



  1. While observing the resistance value shown on the ohmmeter, disconnect branch wire connector (except L97) from the CAN No. 3 junction connector until the resistance becomes normal (6 kΩ or higher (for +B short) or 200 Ω or higher (for ground short)).


    C252630E01


    Text in Illustration 
    *1
    CAN No. 3 Junction Connector
    *2
    Junction Connector B Side
    *3
    Junction Connector A Side
    *4
    Earth Terminal
    *5
    Front view of wire harness connector
    (to CAN No. 3 Junction Connector)
    -
    -

    Terminal No. (Symbol)
    Wiring Color
    Connected to
    L97-1 (CANH)
    P
    Power management control ECU
    L97-2 (CANL)
    V
    L98-1 (CANH)
    LG
    Seat belt control ECU
    L98-2 (CANL)
    L
    L99-1 (CANH)
    B
    Driving support ECU
    L99-2 (CANL)
    W

    HINT:
    1. The connectors connected to the CAN junction connector can be distinguished by the colors of the bus wire.
    2. Reconnecting the connectors to non-specified positions on the CAN junction connector does not affect system operation.

      Result:

      Result
      Proceed to
      The resistance between terminals CANP and BAT, or the resistance between terminals CANN and BAT is still below 6 kΩ when all the specified connectors are disconnected from the CAN junction connector.
      (There is no short to +B in the branch wires.)
      A
      The resistance between terminals CANP and GND, or the resistance between terminals CANN and GND is still below 200 Ω when all the specified connectors are disconnected from the CAN junction connector.
      (There is no short to GND in the branch wires.)
      The resistance between terminals CANP and BAT, or the resistance between terminals CANN and BAT becomes normal (6 kΩ or higher) when a connector is disconnected from the CAN junction connector.
      (There is a short to +B in one of the areas related to one or more of the disconnected branch wires.)
      B
      The resistance between terminals CANP and GND, or the resistance between terminals CANN and GND becomes normal (200 Ω or higher) when a connector is disconnected from the CAN junction connector.
      There is a short to GND in one of the areas related to one or more of the disconnected branch wires.)



B
Go to step 12
A

REPLACE CAN NO. 3 JUNCTION CONNECTOR 

12.CHECK FOR SHORT IN CAN NO. 2 BUS WIRE (ECUS)
  1. Reconnect the connector for the bus wire that is shorted to +B or GND to the CAN junction connector (the connector that caused the bus wire resistance to change to 6 kΩ or higher (for +B short) or 200 Ω or higher (for ground short) when it was disconnected).

  1. Disconnect the connector that includes terminals CANH and CANL from the ECU to which the bus wire shorted to +B or GND is connected.



    A204445E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Purpose
    L5-34 (CA2H) - L5-6 (E1)
    Power switch off
    200 Ω or higher
    Inspection for CANH ground short
    L5-35 (CA2L) - L5-6 (E1)
    Power switch off
    200 Ω or higher
    Inspection for CANL ground short
    L5-34 (CA2H) - L5-1 (AM22)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Inspection for CANH +B short
    L5-35 (CA2L) - L5-1 (AM22)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Inspection for CANL +B short

    HINT:
    It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check CAN No. 2 Bus Wire inspection.
    Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check CAN No. 2 Bus Wire inspection.

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH WIRE OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR