Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0516-769    Battery Temperature Sensor Circuit Low

DTC    P0517-770    Battery Temperature Sensor Circuit High

for Preparation Click here


DESCRIPTION


  1. The thermistor assembly (battery temperature sensor) detects the auxiliary battery temperature. The resistance of the thermistor assembly built into the thermistor changes in accordance with changes in the auxiliary battery temperature. The lower the auxiliary battery temperature, the higher the thermistor assembly resistance. Conversely, the higher the temperature, the lower the resistance. The thermistor is connected to the power management control ECU (HV CPU). A voltage of 5 V is supplied to the thermistor assembly from the THB terminal of the power management control ECU (HV CPU) through its internal resistor R. This means that resistor R and the thermistor assembly are connected in series. The voltage at the THB terminal and the resistance value change in accordance with changes in the auxiliary battery temperature. Based on this signal, the power management control ECU (HV CPU) reduces the charging current when the auxiliary battery temperature is high to protect the auxiliary battery.

    HINT:
    Characteristics of the thermistor resistance (reference values) are as follows.

    Terminal
    THB
    (with Connector Disconnected)
    Resistance
    Ambient Temperature
    THB - E2
    4.5 to 5.5 V
    3.00 to 3.73 kΩ
    Approximately 50°F (10°C)
    1.60 to 1.80 kΩ
    Approximately 77°F (25°C)
    0.80 to 1.00 kΩ
    Approximately 104°F (40°C)



    A180218E02


DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0516
769
Malfunction in the thermistor assembly (battery temperature sensor) circuit (short to GND)
(1 trip detection logic)
  1. Thermistor assembly
  2. Wire harness or connector
  3. Power management control ECU
P0517
770
Malfunction in the thermistor assembly (battery temperature sensor) circuit (open or short to +B))
(1 trip detection logic)

Related Data List 
DTC No.
Data List
P0516-769
Auxiliary Batt Temperature
P0517-770

WIRING DIAGRAM


A166989E02


INSPECTION PROCEDURE

HINT:
  1. Read the freeze frame data using the Techstream. In the freeze frame data, some information is recorded about the engine conditions at the moment a malfunction occurred. This information can be helpful when troubleshooting.
  2. After confirming that DTC P0516-769 or P0517-770 is output, use the Techstream to check "Auxiliary Batt Temperature" in the power management control ECU Data List.

    Displayed Temperature
    Malfunction
    -40°F (-40°C)
    Open circuit or short to +B
    419°F (215°C)
    Short circuit or short to GND
  3. After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
    1. Turn the power switch on (IG) and wait for 5 seconds or more.

1.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)


    A216617
  1. Check the connections of the power management control ECU connectors.

    OK:
    The connectors are connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


2.READ VALUE USING TECHSTREAM (AUXILIARY BATT TEMPERATURE)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.

  1. Read the Data List.

    Result:
    Result
    Proceed to
    -40°F (-40°C)
    A
    419°F (215°C)
    B
    Same as actual temperature
    C

  1. Turn the power switch off.



B
Go to step 5

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


3.READ VALUE USING TECHSTREAM (CHECK FOR OPEN)


    A216307
  1. Disconnect connector S17 from the thermistor assembly.



    A237420E04
  1. Connect terminals 2 (THB) and 1 (E2) of vehicle side connector S17 of the thermistor assembly.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.

  1. Read the Data List.

    OK:
    Tester Display
    Condition
    Specified Condition
    Auxiliary Batt Temperature
    Terminals THB and E2 connected.
    Power switch on (IG)
    419°F (215°C)

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Thermistor Assembly)

  1. Turn the power switch off.

  1. Connect the thermistor assembly connector.



NG
Go to step 4
OK

REPLACE THERMISTOR ASSEMBLY 

4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - THERMISTOR ASSEMBLY)


    A204441E98
  1. Connect terminals 28 (THB) and 30 (ETHB) of connector L5 of the power management control ECU.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.

  1. Read the Data List.

    OK:
    Tester Display
    Condition
    Specified Condition
    Auxiliary Batt Temperature
    Terminals THB and ETHB connected.
    Power switch on (IG)
    419°F (215°C)

    Text in Illustration 
    *1
    Component with harness connected
    (Power Management Control ECU)

  1. Turn the power switch off.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

5.READ VALUE USING TECHSTREAM (CHECK FOR SHORT)


    A216307
  1. Disconnect connector S17 from the thermistor assembly.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.

  1. Read the Data List.

    OK:
    Tester Display
    Condition
    Specified Condition
    Auxiliary Batt Temperature
    Power switch on (IG)
    -40°F (-40°C)

  1. Turn the power switch off.



NG
Go to step 6
OK

REPLACE THERMISTOR ASSEMBLY 

6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - THERMISTOR ASSEMBLY)
  1. Disconnect connector S17 from the thermistor assembly.



    A204554E03
  1. Disconnect connector L5 from the power management control ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    L5-28 (THB) - S17-2 (THB)
    Power switch off
    Below 1 Ω
    L5-30 (ETHB) - S17-1 (E2)
    Power switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    L5-28 (THB) or S17-2 (THB) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    L5-30 (ETHB) or S17-1 (E2) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Thermistor Assembly)
    *2
    Rear view of wire harness connector
    (to Power Management Control ECU)

  1. Connect the thermistor assembly connector.

  1. Connect the power management control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)