Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0340-886    Camshaft Position Sensor "A" Circuit

for Preparation Click here


DESCRIPTION

If the engine is determined to be running based on the engine speed signal sent from the ECM via CAN communication, but the engine speed indicated by pulses of the camshaft position sensor sent from the ECM via serial communication is not received, the power management control ECU (HV CPU) will store this DTC.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0340
886
Malfunction in the camshaft position sensor (GI signal) circuit*
(1 trip detection logic)
  1. Wire harness or connector
  2. Camshaft position sensor
  3. Inverter with converter assembly
  4. ECM
  5. Power management control ECU

HINT:
*: When this DTC is stored, vibration may occur when the engine is stopped.


Related Data List 
DTC No.
Data List
P0340A-886
  1. Engine Revolution
  2. Engine Rev (Sensor)
  3. Engine Speed (SFI System)
  4. Crank Position

WIRING DIAGRAM


A216635E01


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

    HINT:
    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the power switch on (READY).
  2. With the vehicle stopped, push the P position switch (transmission shift main switch).
  3. Depress the accelerator pedal to start the engine.
  4. Depress the accelerator pedal and maintain the engine speed at 1000 rpm or more for 5 seconds or more.

1.CHECK DTC OUTPUT (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    DTC P0340-886 only is output.
    A
    DTC P0343-747 is also output.
    B

  1. Turn the power switch off.



B
Go to step 7
A


2.CHECK CONNECTOR CONNECTION CONDITION (ECM CONNECTOR)


    A216627
  1. Check the connections of the ECM connectors.

    OK:
    The connectors are connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


3.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)


    A216617
  1. Check the connections of the power management control ECU connectors.

    OK:
    The connectors are connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


4.CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)
  1. Turn the power switch on (READY).



    A216633E01
  1. Connect an oscilloscope between the power management control ECU terminals specified in the table below, and measure the waveform.
    Item
    Content
    Terminal
    A21-16 (GI) - L5-6 (E1)
    Equipment Setting
    5 V/DIV., 20 ms./DIV.
    Condition
    Power switch on (READY) with engine running

Text in Illustration 
*1
Component with harness connected
(Power Management Control ECU)

Result:
Result
Proceed to
Normal
A
Waveform is flat, and is stuck on the +B side.
B
Waveform is flat, and is stuck on the GND side.
C



B
Go to step 6

C
Go to step 7
A


5.CHECK FOR INTERMITTENT PROBLEMS
  1. Check for intermittent problems (Click here).



NG
REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU)
  1. Disconnect connector D28 from the ECM.

  1. Turn the power switch on (IG).



    A216818E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D28-48 (G2O) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to ECM)

    NOTICE:
    Turning the power switch on (IG) with the ECM connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Connect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

7.CHECK HARNESS AND CONNECTOR (ECM - POWER MANAGEMENT CONTROL ECU, INVERTER WITH CONVERTER)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector D28 from the ECM.

  1. Disconnect connector A21 from the power management control ECU.

  1. Disconnect connector A59 from the inverter with converter assembly.

  1. Turn the power switch on (IG).



    A216818E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D28-48 (G2O) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to ECM)

    NOTICE:
    Turning the power switch on (IG) with the inverter with converter assembly connector, power management control ECU connector and ECM connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D28-48 (G2O) - Body ground
    Power switch off
    10 kΩ or higher

  1. Connect the ECM connector.

  1. Connect the power management control ECU connector.

  1. Connect the inverter with converter assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK POWER MANAGEMENT CONTROL ECU
  1. Disconnect all the connectors from the power management control ECU.



    A204442E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A21-16 (GI) - L5-6 (E1)
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Power Management Control ECU)

  1. Connect the power management control ECU connectors.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK


9.CHECK INVERTER WITH CONVERTER ASSEMBLY

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector A59 from the inverter with converter assembly.



    A215652E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A59-29 (GI) - A59-28 (GND1)
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Inverter with Converter Assembly)

  1. Connect the inverter with converter assembly connector.



NG
REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)
OK

REPLACE ECM (Click here)