Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM

VEHICLE PROXIMITY NOTIFICATION SYSTEM > Even when Engine is Started or Transmission Shift Main Switch (P Position Switch) is Pushed, Sound does not Stop

for Preparation Click here


DESCRIPTION

The vehicle approaching speaker controller receives engine oil pressure switch signals from the engine oil pressure switch assembly and P position switch signals from the transmission control ECU assembly, and produces the warning sound from the vehicle approaching speaker assembly.

WIRING DIAGRAM


E289607E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (Oil Pressure SW)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.

  1. Check the value(s) by referring to the table below.

    Vehicle Proximity Notification System 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Oil Pressure SW
    Oil pressure switch / OFF or ON
    OFF: Engine started
    ON: Engine not started
    -

    Result:
    Result
    Proceed to
    The Techstream display changes according to engine operation
    A
    The Techstream display does not change according to engine operation
    B



B
Go to step 6
A


2.READ VALUE USING TECHSTREAM (Shift Position)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.

  1. Check the value(s) by referring to the table below.

    Vehicle Proximity Notification System 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Shift Position
    P position switch / Not Parking or Parking
    Not Parking or Parking
    -

    Result:
    Result
    Proceed to
    The Techstream display changes according to the selected shift state
    A
    The Techstream display does not change according to the selected shift state
    B



B
Go to step 3
A

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

3.CHECK VEHICLE APPROACHING SPEAKER CONTROLLER (SHIFT)
  1. Disconnect the A23 transmission control ECU assembly connector.



    E285951E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A23-20 (IND) - Body ground
    Power switch on (IG)
    8 V or higher
    Power switch off
    Below 2.5 V

Text in Illustration 
*a
Front view of wire harness connector
(to Transmission Control ECU Assembly)


NG
Go to step 5
OK


4.CHECK TRANSMISSION CONTROL ECU ASSEMBLY
  1. Reconnect the A23 transmission control ECU assembly connector.



    E285952E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A23-20 (IND) - Body ground
    Power switch on (IG), park (P) selected
    Below 2.5 V
    Power switch on (IG), park (P) not selected
    8 V or higher

Text in Illustration 
*a
Component with harness connected
(Transmission Control ECU Assembly)


NG
REPLACE TRANSMISSION CONTROL ECU ASSEMBLY (Click here)
OK

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

5.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - TRANSMISSION CONTROL ECU ASSEMBLY)
  1. Disconnect the L140 vehicle approaching speaker controller connector.

  1. Disconnect the A23 transmission control ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L140-11 (SFTP) - A23-20 (IND)
    Always
    Below 1 Ω
    L140-11 (SFTP) or A23-20 (IND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

6.CHECK ENGINE OIL PRESSURE SWITCH ASSEMBLY (INPUT SIGNAL)
  1. Disconnect the L140 vehicle approaching speaker controller connector.



    E285131E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L140-12 (OPSW) - Body ground
    Idling*
    8 V or higher
    Power switch on (IG)
    Below 2 V

HINT:
*: Put the engine in inspection mode (Click here).

Text in Illustration 
*a
Front view of wire harness connector
(Vehicle Approaching Speaker Controller)


NG
Go to step 7
OK

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

7.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - ENGINE OIL PRESSURE SWITCH ASSEMBLY)
  1. Disconnect the L140 vehicle approaching speaker controller connector.

  1. Disconnect the D26 engine oil pressure switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L140-12 (OPSW) - D26-1
    Always
    Below 1 Ω
    L140-12 (OPSW) or D26-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ENGINE OIL PRESSURE SWITCH ASSEMBLY (Click here)