Home › Engine / Hybrid System › CRUISE CONTROL › LANE-KEEPING ASSIST SYSTEM

LANE-KEEPING ASSIST SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK DRIVING SUPPORT ECU

E184662E10

  1. Measure the voltage and/or resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L60-6 (SPSW) - L60-25 (GND)
    R - W-B
    Steering pad switch signal
    (Lane keeping assist main switch signal)
    Power switch on (IG)
    Lane keeping assist main switch off
    11 to 14 V
    L60-6 (SPSW) - L60-25 (GND)
    R - W-B
    Steering pad switch signal
    (Lane keeping assist main switch signal)
    Power switch on (IG)
    Lane keeping assist main switch on
    6 to 7 V
    L60-10 (CCHG) - L60-25 (GND)
    G - W-B
    Cruise control main switch signal
    Power switch on (IG)
    MODE switch on
    Below 1 V
    L60-10 (CCHG) - L60-25 (GND)
    G - W-B
    Cruise control main switch signal
    Power switch on (IG)
    MODE switch off
    11 to 14 V
    L60-9 (WASH) - L60-25 (GND)
    V - W-B
    Washer switch signal
    Power switch on (IG)
    Washer switch off
    11 to 14 V
    L60-9 (WASH) - L60-25 (GND)
    V - W-B
    Washer switch signal
    Power switch on (IG)
    Washer switch on
    Below 1 V
    L60-17 (CA2L)* - L60-25 (GND)
    W - W-B
    CAN communication signal
    Power switch on (IG)
    Pulse generation
    (See waveform 1)
    L60-18 (CA1N)* - L60-25 (GND)
    L - W-B
    CAN communication signal
    Power switch on (IG)
    Pulse generation
    (See waveform 2)
    L60-23 (CCS) - L60-25 (GND)
    V - W-B
    Cruise control main switch signal
    Power switch on (IG)
    11 to 14 V
    L60-23 (CCS) - L60-25 (GND)
    V - W-B
    Cruise control main switch signal
    Power switch on (IG),
    CANCEL switch on
    6.6 to 10.1 V
    L60-23 (CCS) - L60-25 (GND)
    V - W-B
    Cruise control main switch signal
    Power switch on (IG),
    Main switch on
    Below 1 V
    L60-24 (HITP) - L60-25 (GND)
    G - W-B
    CAN signal
    (Hi temperature)
    Power switch on (IG)
    11 to 14 V
    L60-30 (B) - Body ground
    B - Body ground
    Power supply
    Always
    11 to 14 V
    L60-25 (GND) - Body ground
    W-B - Body ground
    Body ground
    Always
    Below 1 Ω
    L60-27 (STP-) - Body ground
    Y - Body ground
    Stop light switch assembly signal input
    Depress brake pedal
    7.5 to 14 V
    L60-27 (STP-) - Body ground
    Y - Body ground
    Stop light switch assembly signal input
    Release brake pedal
    Below 1 V
    L60-28 (ST1-) - Body ground
    R - Body ground
    Stop light switch assembly signal input
    Power switch on (IG),
    release brake pedal
    7.5 to 14 V
    L60-28 (ST1-) - Body ground
    R - Body ground
    Stop light switch assembly signal input
    Power switch on (IG),
    depress brake pedal
    Below 1 V
    L60-30 (B) - L60-25 (GND)
    B - W-B
    Power source
    Power switch on (IG)
    11 to 14 V
    L60-32 (WIP2) - L60-25 (GND)
    P - W-B
    Wiper switch signal
    Power switch on (IG),
    Wiper switch off
    Below 1 V
    L60-32 (WIP2) - L60-25 (GND)
    P - W-B
    Wiper switch signal
    Power switch on (IG),
    Wiper switch LO position
    6 to 7 V
    L60-32 (WIP2) - L60-25 (GND)
    P - W-B
    Wiper switch signal
    Power switch on (IG),
    Wiper switch HI position
    11 to 14 V
    L60-34 (WNKR) - L60-25 (GND)
    B -W-B
    Winker R signal
    Power switch on (IG)
    Winker off
    11 to 14 V
    L60-34 (WNKR) - L60-25 (GND)
    B - W-B
    Winker R signal
    Power switch on (IG)
    Winker R
    Below 1 V
    L60-35 (WNKL) - L60-25 (GND)
    P - W-B
    Winker L signal
    Power switch on (IG)
    Winker off
    11 to 14 V
    L60-35 (WNKL) - L60-25 (GND)
    P - W-B
    Winker L signal
    Power switch on (IG)
    Winker L
    Below 1 V
    L60-39 (CA2H)* - L60-25 (GND)
    B - W-B
    CAN communication signal
    Power switch on (IG)
    Pulse generation
    (See waveform 3)
    L60-40 (CA1P)* - L60-25 (GND)
    Y - W-B
    CAN communication signal
    Power switch on (IG)
    Pulse generation
    (See waveform 4)
    *: with Pre-collision system



  2. A086155E19
  3. WAVEFORM 1

    1. CAN communication signal
      Driving support ECU Terminal Name
      Between CA2L and GND
      Tester Range
      1 V/DIV., 10 μsec./DIV.
      Condition
      Power switch on (IG)

      HINT:
      The waveform varies depending on the CAN communication signal.



  4. A086154E17
  5. WAVEFORM 2

    1. CAN communication signal
      Driving support ECU Terminal Name
      Between CA1N and GND
      Tester Range
      1 V/DIV., 10 μsec./DIV.
      Condition
      Power switch on (IG)



  6. A086154E17
  7. WAVEFORM 3

    1. CAN communication signal
      Driving support ECU Terminal Name
      Between CA2H and GND
      Tester Range
      1 V/DIV., 10 μsec./DIV.
      Condition
      Power switch on (IG)

      HINT:
      The waveform varies depending on the CAN communication signal.



  8. A086155E19
  9. WAVEFORM 4

    1. CAN communication signal
      Driving support ECU Terminal Name
      Between CA1P and GND
      Tester Range
      1 V/DIV., 10 μsec./DIV.
      Condition
      Power switch on (IG)