Home › Engine / Hybrid System › CRUISE CONTROL › LANE-KEEPING ASSIST SYSTEM

LANE-KEEPING ASSIST SYSTEM > SYSTEM DESCRIPTION

for Preparation Click here



LANE-KEEPING ASSIST DESCRIPTION


  1. The lane-keeping assist system uses an image of the road from the lane-recognition camera sensor to detect the lane markers for the lane that the vehicle is in. If the system detects that the vehicle is about to move out of its lane, it uses the warning buzzer, multi-information display and steering assistance to warn the driver.


    A217251E01


    Text in Illustration 
    *1
    White lines
    *2
    Steering wheel
    *3
    Radar cruise display
    *4
    Radar cruise set vehicle speed
    *5
    LKA Indicator
    -
    -
    1. White lines
      1. The white line indicate the condition of the lane keeping assist system.
        1. Lines are not displayed: Lane keeping assist system is off.
        2. Thin lines are displayed: Lane keeping assist system is off.
        3. Thick lines are displayed: Lane keeping assist system is operating.
    2. Steering wheel
      1. When the steering wheel is displayed, this indicates that the lane keeping assist function is operating.
    3. Radar cruise display
      1. Indicates operation conditions for radar cruise
    4. Radar cruise set vehicle speed
      1. Indicates the set vehicle speed when the radar cruise is activated
    However, in the following conditions, the lane-keeping assist system may not function normally.
    1. Vehicle is near toll booths or similar areas
    2. Road has no lane marker
    3. Lane marker are cracked
    4. Road has yellow lines
    5. There is a shadow on either of the lane marker
    6. As a result of reflections, road surface is bright
    7. Road with reflective surface similar to concrete road
    8. Area where brightness changes suddenly, such as entrances and exits of tunnels or similar area
    9. Bright light directed at sensor
    10. Incline of road varies, winding road or other type of road where road surface is irregular
    11. Bad weather
    12. Frozen or snowy roads
    13. Road surface with water or other liquid


SYSTEM OPERATION
  1. Lane departure warning function:
    The lane departure warning function operates when the lane-keeping assist switch is on, the vehicle speed is 48 km/h (30 mph) or more, and lane markers on the road surface are detected. With the lane departure warning function operating, if the vehicle is about to move out of the lane and this is detected by the driving support ECU, the ECU uses the warning buzzer and the multi-information display to warn the driver. Also, the ECU uses the electronic power steering system's motor to apply steering force and give suggestions to the driver for lane departure avoidance.

    HINT:
    This function only provides suggestions for lane departure avoidance. This function does not automatically move the vehicle within a lane.


    Lane Departure Warning Function Operation Stop Condition
    Restart Condition
    When vehicle speed is less than 48 km/h (30 mph)
    When vehicle speed is 48 km/h (30 mph)
    When turn signal light switch is operated
    When turn signal light switch is turned off
    When steering force above a specified amount is applied
    When steering force above a specified amount is not applied
    When windshield wiper switch is set to Lo or Hi
    When windshield wiper switch is turned off
    When lane recognition camera sensor cannot detect lane marker
    When lane recognition camera sensor can detect lane marker
    While brake pedal operation is being detected
    After brake pedal operation is completed
    After lane departure warning has been issued
    When the vehicle is back to its lane, or a few seconds have passed since warning was executed

  2. Lane-keeping assist function:
    The lane-keeping assist function operates when the lane-keeping assist switch is ON, the vehicle speed is approximately 72 to 180 km/h (45 to 112 mph) and the dynamic radar cruise control system is ON. With the lane-keeping assist function operating, steering assistance is provided for the driver according to the driving conditions so that the vehicle stays near the midpoint of a lane. When the vehicle cannot be maintained within a lane and this is detected by the driving support ECU, the ECU uses the warning buzzer and the multi-information display to warn the driver. During the lane-keeping assist function operation, if any of the following conditions occurs, the lane-keeping assist function will stop operating. If the condition is no longer detected, the lane-keeping assist function will automatically start operating again.

    Lane-keeping Assist Function Operation Stop Condition
    Restart Condition
    When lane recognition camera sensor cannot detect lane marker
    When lane recognition camera sensor can detect lane marker
    When vehicle speed is not within 72 to 180 km/h (45 to 112 mph)
    When vehicle speed is within 72 to 180 km/h (45 to 112 mph)
    When turn signal light switch is operated
    When turn signal light switch is turned off
    When windshield wiper switch is set to Lo or Hi
    When windshield wiper switch is turned off
    When steering force above a specified amount is applied
    When steering force above specified amount is not detected
    When steering force above a specified amount does not occur*
    When steering operation is detected
    When changing lanes
    When driving within a lane is confirmed

    HINT:
    *: This refers to situations where the vehicle is driven for 15 seconds or more on a lane that is straight; or 5 seconds or more on a curved road (curve radius 1000 m (3281 ft.) or less).

During the lane-keeping assist function operation, if any of the following conditions is detected, the lane-keeping assist function will stop operating.
  1. When dynamic radar cruise control system is canceled*
  2. When lane-keeping assist switch is turned off
  3. When object recognition camera sensor's interior temperature is 70°C (158°F) or more
  4. When lane-keeping assist system is malfunctioning

    HINT:
    *: During the lane-keeping assist function operation, if the dynamic radar cruise control system is canceled, the lane-keeping assist system will change from the lane-keeping assist function to the lane departure warning function.


LKA INDICATOR LIGHT
The LKA indicator light is built into the combination meter. It informs the driver of the operational condition or malfunctions of the lane keeping assist system.

LKA Indicator
System Condition
Off
Not activated
On
Activated
Blink
Malfunction

FUNCTION OF MAIN COMPONENTS

Item
Outline
Power steering control ECU
  1. Based on signal from driving support ECU, power steering control ECU applies steering force
  2. Sends driver's steering operation information to driving support ECU
Brake booster with master cylinder (skid control ECU)
  1. Receives buzzer operation signal from driving support ECU, and sends it to skid control buzzer.
  2. Sends vehicle speed information to driving support ECU
Steering angle sensor
Detects driver's steering torque and transmits its signal to power steering control ECU
Yaw rate sensor
Detects yaw rate of vehicle and transmits its signal to driving support ECU
Combination meter (LKA indicator light)
  1. Turns on when lane-keeping assist switch is on
  2. If driving support ECU detects malfunction, this light flashes to warn driver
Combination meter (Warning buzzer)
When lane-keeping assist system detects malfunction, warning buzzer sounds once to inform driver
Cruise control main switch
Turns cruise control system on / off
Stop light switch assembly
Detects depressing of brake pedal and transmits its signal to driving support ECU
Skid control buzzer
This buzzer sounds upon receiving signal from brake booster with master cylinder (skid control ECU)
Vehicle speed sensor
Sends vehicle speed signal to brake booster with master cylinder (skid control ECU), and then it is sent to driving support ECU
Driving support ECU
  1. Based on lane marker information and information from other functions, driving support ECU sends signals to electronic power steering control ECU so that it applies steering force
  2. Controls multi-information display and buzzer sound condition
  3. Monitors lane-keeping assist malfunctions, and records diagnostic information
Lane-recognition camera sensor
Obtains an image of the road in front of the vehicle. An internal image processor generates information such as lane width, road curvature, yaw angle and the amount of vehicle offset from the center of the lane, and this information is sent to the driving support ECU.
Millimeter wave radar sensor
Detects a preceding vehicle and calculates the distance to the preceding vehicle.
Lane keeping assist main switch
Activates or deactivates the system.
Windshield wiper switch
Sends the operation condition of the windshield wiper switch to the driving support ECU.
Turn signal switch
Sends the operation condition of the turn signal switch to the driving support ECU.
Combination meter
  1. Controls the multi-information display and illumination of the LKA indicator in accordance with the respective display request signals from the driving support ECU.
  2. Sounds the meter buzzer in accordance with the buzzer request signal from the driving support ECU.
Multi-information display
Displays the operating condition of the system.