Home › Engine / Hybrid System › 2ZR-FXE INTAKE / EXHAUST › EXHAUST MANIFOLD

EXHAUST MANIFOLD > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A212651
  1. Install the No. 2 exhaust manifold heat insulator with the 3 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



2. INSTALL EXHAUST MANIFOLD
  1. Install 2 new gaskets.



  1. Type A:



    1. Install the exhaust manifold with the 7 nuts.

      Torque:
      21 N*m{ 214 kgf*cm , 15 ft.*lbf }



      A307472E01


      Text in Illustration 
      *A
      Type A
      *B
      Type B
      *C
      Type C
      -
      -

  1. Type B and Type C:

    1. Install the exhaust manifold with 7 new nuts.

      Torque:
      Type B:
      37 N*m{ 377 kgf*cm , 27 ft.*lbf }
      Type C:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }



3. INSTALL MANIFOLD STAY


    A212649
  1. Install the manifold stay with the 3 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



4. INSTALL AIR FUEL RATIO SENSOR

HINT:
Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).



    A216698
  1. Using SST, install the air fuel ratio sensor.

    SST
    09224-00010  

    Torque:
    without SST:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    with SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    NOTICE:
    1. The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.).
    2. The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 300 mm (11.81 in.) (Click here).
    3. This torque value is effective when SST is parallel to the torque wrench.



    A212298
  1. Connect the air fuel ratio sensor connector and clamp.



5. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A212648
  1. Install the No. 1 exhaust manifold heat insulator with the 3 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



6. INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR


    A212647
  1. Install the front No. 1 floor heat insulator with the 3 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



7. INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/ Exhaust Heat Recirculation System)

NOTICE:
When installing the heater water hose, ensure that the exhaust heat recirculation system is filled with coolant. Otherwise, the engine water pump assembly may be damaged.



    A077857
  1. Using a vernier caliper, measure the free length of the compression springs.
    Minimum (front)
    41.5 mm (1.63 in.)
    Minimum (rear)
    38.5 mm (1.52 in.)

    HINT:
    If the free length is less than minimum, replace the compression spring.

  1. Temporarily install 2 new gaskets to the exhaust manifold and front exhaust pipe assembly.



    A181728E38
  1. Using a plastic hammer and wooden block, tap in each gasket until its surface is flush with the exhaust manifold and front exhaust pipe assembly.
    Text in Illustration 
    *1
    Exhaust Manifold and Front Exhaust Pipe Assembly
    *2
    Gasket
    *a
    Wooden Block

    NOTICE:
    1. Be careful with the installation direction of the gaskets.
    2. Do not reuse the gaskets.
    3. Do not damage the gaskets.
    4. Do not push in the gaskets by using the exhaust pipes when connecting them.

  1. Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.



    A215918
  1. Install the front exhaust pipe assembly with the 4 bolts and 4 compression springs.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



    A212644
  1. Connect the 2 heater water hoses and slide the 2 clips to secure them.



    A212646
  1. Engage the 3 clamps.

  1. Connect the heated oxygen sensor connector.



8. INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/o Exhaust Heat Recirculation System)


    A077857
  1. Using a vernier caliper, measure the free length of the compression springs.
    Minimum (front)
    41.5 mm (1.63 in.)
    Minimum (rear)
    38.5 mm (1.52 in.)

    HINT:
    If the free length is less than minimum, replace the compression spring.

  1. Temporarily install 2 new gaskets to the exhaust manifold and front exhaust pipe assembly.



    A181728E38
  1. Using a plastic hammer and wooden block, tap in each gasket until its surface is flush with the exhaust manifold and front exhaust pipe assembly.
    Text in Illustration 
    *1
    Exhaust Manifold and Front Exhaust Pipe Assembly
    *2
    Gasket
    *a
    Wooden Block

    NOTICE:
    1. Be careful with the installation direction of the gaskets.
    2. Do not reuse the gaskets.
    3. Do not damage the gaskets.
    4. Do not push in the gaskets by using the exhaust pipes when connecting them.

  1. Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.



    A215918
  1. Install the front exhaust pipe assembly with the 4 bolts and 4 compression springs.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



9. ADD COOLANT (for Engine with Exhaust Heat Recirculation System)
  1. Tighten the radiator drain cock plug.

  1. Remove the reservoir tank cap.



    A213418E01
  1. Add coolant to B line of the reservoir tank.
    Text in Illustration 
    *1
    B Line

    Standard Capacity:
    Item
    Capacity
    Engine coolant
    w/ Exhaust Heat Recirculation System:
    7.2 liters (7.6 US qts, 6.3 lmp. qts)
    w/o Exhaust Heat Recirculation System:
    6.5 liters (6.8 US qts, 5.7 lmp. qts)

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Squeeze the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the reservoir tank cap.

  1. Put the engine in inspection mode (Click here).

  1. Bleed air from the cooling system.

    NOTICE:
    1. Before starting the engine, turn the A/C switch off.
    2. Adjust the heater control to the maximum hot setting.
    3. Adjust the blower speed to low setting.


    1. Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.

      HINT:
      The thermostat opening timing can be confirmed by squeezing the inlet radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the hose.

      CAUTION:
      When squeezing the radiator hose:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

    2. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air from the system.

      CAUTION:
      When squeezing the radiator hose:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.



    A213418E02
  1. After the engine has cooled down, check that the coolant level is between full and low.
    Text in Illustration 
    *1
    Full Line
    *2
    Low Line
    If the coolant level is low, add coolant to the full line on the reservoir tank.



10. INSPECT FOR COOLANT LEAK (for Engine with Exhaust Heat Recirculation System)

CAUTION:
Do not remove the reservoir tank cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch off.

  1. Remove the reservoir tank cap.



    A213419
  1. Fill the radiator and reservoir with coolant, and then attach a radiator cap tester.

  1. Put the engine in inspection mode (Click here).

  1. Warm up the engine.

  1. Using the reservoir cap tester, increase the pressure inside the radiator to 108 kPa (1.1 kgf/cm2, 16 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator, front exhaust pipe assembly and the heater hose around and engine water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.

  1. Remove the radiator cap tester.

  1. Install the reservoir tank cap.



11. INSTALL FRONT CENTER FLOOR BRACE


    A264084
  1. Install the front center floor brace with the 4 bolts.

    Torque:
    51 N*m{ 520 kgf*cm , 38 ft.*lbf }



12. INSTALL FRONT NO. 3 ENGINE UNDER COVER


    A212642
  1. Install the front No. 3 engine under cover with the 4 clips.



13. INSTALL NO. 2 ENGINE UNDER COVER


14. INSTALL NO. 1 ENGINE UNDER COVER


15. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.
  1. Perform "Inspection After Repair" after repairing and replacing an exhaust gas leak (Click here).