Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER

BRAKE BOOSTER > REMOVAL

for Preparation Click here



1. REMOVE REAR NO. 2 FLOOR BOARD (for Separate Type)


    B227787E01
  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



2. REMOVE REAR DECK FLOOR BOX
  1. Remove the rear deck floor box.



3. REMOVE REAR NO. 3 FLOOR BOARD


    B227791
  1. Disengage the 2 guides and remove the rear No. 3 floor board.



4. DISABLE BRAKE CONTROL
  1. Wait at least 2 minutes after the power switch off.

    NOTICE:
    When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



    C205666
  1. Disconnect the reservoir level switch connector with the parking brake applied.

  1. Disconnect the cable from the auxiliary battery negative (-) terminal.

  1. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

  1. Check that the brake pedal can not be further depressed.

  1. Release the parking brake.



5. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B223658
  1. Remove the 2 screws <D>.

  1. Disengage the claw and guide.

  1. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.



6. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
(Click here)


7. REMOVE COWL BODY MOUNTING REINFORCEMENT LH


    C205667
  1. Remove the 3 bolts and cowl body mounting reinforcement LH.



8. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY


    C205668E01
  1. Disengage the 2 clamps and guide of the wire harness.
    Text in Illustration 
    *1
    Clamp
    *2
    Guide



    C205670
  1. Disengage the claw and bend the No. 1 heater air duct splash shield seal.



    C205672
  1. Disengage the claw and bend the water guard plate RH.



    C205669
  1. Remove the 9 bolts and outer cowl top panel sub-assembly.



9. DRAIN BRAKE FLUID

NOTICE:
If brake fluid leaks onto any painted surface, immediately wash it off.



10. REMOVE BRAKE PEDAL RETURN SPRING


    C205687
  1. Remove the brake pedal return spring from the brake pedal support assembly and push rod pin.



11. REMOVE PUSH ROD PIN


    C205688
  1. Remove the clip and push rod pin to separate the brake pedal support assembly from the push rod clevis.



12. SEPARATE BRAKE MASTER CYLINDER RESERVOIR WITH BRACKET


    C205675
  1. Remove the 2 nuts and separate the brake master cylinder reservoir with bracket.



13. DISCONNECT NO. 1 RESERVOIR HOSE


    C205676E01
  1. Move the 2 clips and disconnect the No. 1 reservoir hose and No. 2 reservoir hose from the brake booster with master cylinder assembly.
    Text in Illustration 
    *1
    No. 1 Reservoir Hose
    *2
    No. 2 Reservoir Hose



14. DISCONNECT NO. 2 RESERVOIR HOSE


15. DISCONNECT BRAKE ACTUATOR HOSE


    C205677
  1. Move the clip and disconnect the brake actuator hose from the brake booster pump assembly.



16. REMOVE BRAKE MASTER CYLINDER RESERVOIR WITH BRACKET


17. REMOVE NO. 5 BRAKE ACTUATOR BRACKET


    C205680
  1. Disengage the clamp.

  1. Remove the 2 nuts and No. 5 brake actuator bracket.



18. REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY


    C205678
  1. Release the lock lever and disconnect the connector from the brake booster with master cylinder assembly.

    NOTICE:
    Be careful not to allow the brake fluid to enter the removed connector.



    C205681
  1. Remove the 2 bolts and No. 2 brake tube clamp bracket from the brake booster with master cylinder assembly.



    C205682E01
  1. Using a union nut wrench, disconnect the 5 brake lines from the brake booster with master cylinder assembly.

  1. Use tags or make a memo to identify the places to reconnect.
    Text in Illustration 
    *1
    to Front Wheel Cylinder LH
    *2
    to Rear Wheel Cylinder RH
    *3
    to Brake Booster Pump Assembly
    *4
    to Rear Wheel Cylinder LH
    *5
    to Front Wheel Cylinder RH



    C205683
  1. Disengage the 2 clamps and separate the brake line.



    C205690E01
  1. Remove the 4 nuts and brake booster with master cylinder assembly.
    Text in Illustration 
    *1
    Connector Portion
    *2
    Union
    *3
    Push Rod Clevis and Boot
    *4
    Front No. 2 Brake Tube

    NOTICE:
    1. Do not kink or damage the brake lines.
    2. Do not carry the brake booster with master cylinder assembly by the portion shown in the illustration.



19. REMOVE BRAKE BOOSTER GASKET