Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM

LIN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


  1. Disconnect the 2C and 2B instrument panel junction block assembly connectors.


    B231709E13


    Text in Illustration 
    *A
    Main body ECU (multiplex network body ECU) with 3 connectors
    -
    -
    *1
    Main body ECU (multiplex network body ECU)
    *2
    3 connectors

    E192848E15


    Text in Illustration 
    *A
    Main body ECU (multiplex network body ECU) with 1 connector
    -
    -
    *1
    Main body ECU (multiplex network body ECU)
    *2
    1 connector

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2C-18 (BECU) - Body ground
    Y - Body ground
    Battery power supply
    Power switch off
    11 to 14 V
    2B-6 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the 2C and 2B instrument panel junction block assembly connectors.

  4. Check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2D-26 (LIN2) - 2B-6 (GND1)
    P - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation
    2A-27 (LIN2) - 2B-6 (GND1)
    P - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may be malfunctioning.


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side)


  1. Disconnect the O2 power window regulator motor assembly (for driver side) connector.


    B203471E31

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O2-2 (B) - O2-1 (GND)
    L - W-B
    Battery power supply
    Power switch off
    11 to 14 V
    O2-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the O2 power window regulator motor assembly (for driver side) connector.

  4. Check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O2-9 (LIN) - O2-1 (GND)
    B - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the power window regulator motor assembly (for driver side) may be malfunctioning.


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Side)


  1. Disconnect the N2 power window regulator motor assembly (for front passenger side) connector.


    B203471E32

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    N2-2 (B) - N2-1 (GND)
    R - W-B
    Battery power supply
    Power switch off
    11 to 14 V
    N2-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the N2 power window regulator motor assembly (for front passenger side) connector.

  4. Check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    N2-9 (LIN) - N2-1 (GND)
    P - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the power window regulator motor assembly (for front passenger side) may be malfunctioning.


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Side)


  1. Disconnect the P4 power window regulator motor assembly (for rear RH side) connector.


    B203471E33

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    P4-2 (B) - P4-1 (GND)
    LA-R - W-B
    Battery power supply
    Power switch off
    11 to 14 V
    P4-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the P4 power window regulator motor assembly (for rear RH side) connector.

  4. Check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    P4-9 (LIN) - P4-1 (GND)
    P - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the power window regulator motor assembly (for rear RH side) may be malfunctioning.


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Side)


  1. Disconnect the Q4 power window regulator motor assembly (for rear LH side) connector.


    B203471E34

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Q4-2 (B) - Q4-1 (GND)
    LA-R - W-B
    Battery power supply
    Power switch off
    11 to 14 V
    Q4-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the Q4 power window regulator motor assembly (for rear LH side) connector.

  4. Check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Q4-9 (LIN) - Q4-1 (GND)
    P - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the power window regulator motor assembly (for rear LH side) may be malfunctioning.


CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


  1. Disconnect the O6 multiplex network master switch assembly connector.


    B131578E16

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O6-11 (B) - O6-12 (GND)
    L - W-B
    Battery power supply
    Power switch off
    11 to 14 V
    O6-12 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the O6 multiplex network master switch assembly connector.

  4. Check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O6-17 (LIN1) - O6-12 (GND)
    P - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the multiplex network master switch assembly may be malfunctioning.


CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) (w/ Moonroof with Solar Panel)


  1. Disconnect the R23 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


    B160074E21

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    R23-1 (B) - R23-2 (E)
    R - W-B
    Battery power supply
    Power switch off
    11 to 14 V
    R23-2 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the R23 sliding roof ECU (sliding roof drive gear sub-assembly) connector.

  4. Check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    R23-4 (MPX1) - R23-2 (E)
    P - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the sliding roof ECU (sliding roof drive gear sub-assembly) may be malfunctioning.


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


  1. Disconnect the L62 certification ECU (smart key ECU assembly) connector.


    B218375E02

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L62-1 (+B) - L62-15 (E)
    B - W-B
    Battery power supply
    Power switch off
    11 to 14 V
    L62-15 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L62 certification ECU (smart key ECU assembly) connector.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L62-16 (IG) - L62-15 (E)
    BE - W-B
    Power switch power supply
    Power switch on (IG)
    11 to 14 V
    L62-16 (IG) - L62-15 (E)
    BE - W-B
    Power switch power supply
    Power switch off
    Below 1 V
    L62-29 (LIN) - L62-15 (E)
    L - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the certification ECU (smart key ECU assembly) may be malfunctioning.


CHECK ID CODE BOX (IMMOBILISER CODE ECU) (for Canada)


  1. Disconnect the L10 ID code box (immobiliser code ECU) connector.


    B113402E11

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L10-1 (+B) - L10-8 (GND)
    B - W-B
    Battery power supply
    Power switch off
    11 to 14 V
    L10-8 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L10 ID code box (immobiliser code ECU) connector.

  4. Check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L10-3 (LIN1) - L10-8 (GND)
    L - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the ID code box (immobiliser code ECU) may be malfunctioning.


CHECK TRANSMISSION CONTROL ECU ASSEMBLY


  1. Disconnect the A23 and A24 transmission control ECU assembly connectors.


    B228550E02

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A23-15 (BATT) - Body ground
    SB - Body ground
    Battery power supply
    Power switch off
    11 to 14 V
    A24-1 (E1) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    A24-5 (E02) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    A24-6 (E01) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the A23 and A24 transmission control ECU assembly connectors.

  4. Check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A24-24 (LIN) - A24-1 (E1)
    L - BR
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the transmission control ECU assembly may be malfunctioning.


CHECK POWER MANAGEMENT CONTROL ECU


  1. Disconnect the L5 and L6 power management control ECU connectors.


    C146689E14

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L5-1 (AM22) - Body ground
    W - Body ground
    Battery power supply
    Power switch off
    11 to 14 V
    L6-7 (AM21) - Body ground
    W - Body ground
    Battery power supply
    Power switch off
    11 to 14 V
    L5-6 (E1) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L5 and L6 power management control ECU connectors.

  4. Check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L6-11 (LIN2) - L5-6 (E1)
    L - BR
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the power management control ECU may be malfunctioning.