Home › Vehicle Interior › SEAT › REAR SEAT ASSEMBLY

REAR SEAT ASSEMBLY > REASSEMBLY

for Preparation Click here



1. INSTALL BENCH TYPE REAR SEAT CUSHION COVER


  1. Using hog ring pliers, install the bench type rear seat cushion cover to the bench type rear seat cushion pad with 14 new hog rings.


    B230050

    NOTICE:
    1. Be careful not to damage the cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the bench type rear seat cushion cover.



  1. Using hog ring pliers, install 28 new hog rings.


    B230048

    NOTICE:
    1. Be careful not to damage the cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the bench type rear seat cushion cover.



2. INSTALL REAR SEATBACK LOCK ASSEMBLY LH


    B230040
  1. Install the rear seatback lock assembly LH to the rear seatback frame sub-assembly LH with the 2 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



3. INSTALL REAR SEATBACK LOCK RELEASE BUTTON LH


    B230039
  1. Turn the rear seatback lock release button LH as shown in the illustration to install it to the rear seatback lock assembly LH.



4. INSTALL SEPARATE TYPE REAR SEATBACK COVER LH


    B230008
  1. Using hog ring pliers, install the separate type rear seatback cover LH to the separate type rear seatback pad LH with 9 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover LH.



5. INSTALL REAR SEATBACK COVER WITH PAD LH
  1. Temporarily install the rear seatback cover with pad LH to the rear seatback frame sub-assembly LH.



    B230006
  1. Engage the 4 claws to install the 2 rear seat headrest supports.



    B230003
  1. Using hog ring pliers, install 13 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover LH.



    B230001
  1. Engage the 6 clips.

  1. Install the 2 clips.



6. INSTALL REAR SEATBACK STOP BUTTON GROMMET


    B230004
  1. Engage the 3 claws to install the rear seatback stop button grommet.



7. INSTALL REAR SEAT SHOULDER BELT GUIDE LH


    B229999
  1. Engage the guide to install the rear seat shoulder belt guide LH with the 2 screws.



8. INSTALL REAR SEATBACK COVER LH


    B230000
  1. Engage the 4 claws to install the rear seatback cover LH.



9. INSTALL REAR SEATBACK LOCK ASSEMBLY RH


    B230011
  1. Install the rear seatback lock assembly RH to the rear seatback frame sub-assembly RH with the 2 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



10. INSTALL REAR SEATBACK LOCK RELEASE BUTTON RH


    B230010
  1. Turn the rear seatback lock release button RH as shown in the illustration to install it to the rear seatback lock assembly RH.



11. INSTALL REAR CENTER SEAT BELT ASSEMBLY


    B221502E01
  1. Install the rear center seat belt assembly with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    Text in Illustration 
    *1
    Protruding Part

    NOTICE:
    Do not allow the rear center seat belt assembly to overlap the protruding part of the rear seat back frame.



12. INSTALL SEPARATE TYPE REAR SEATBACK COVER RH


    B230037
  1. Using hog ring pliers, install the separate type rear seatback cover RH to the separate type rear seatback pad RH with 9 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover RH.



    B230035
  1. Using hog ring pliers, install 7 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover RH.



13. INSTALL REAR SEATBACK COVER WITH PAD RH
  1. Temporarily install the rear seatback cover with pad RH to the rear seatback frame sub-assembly RH.



    B230030
  1. Engage the 4 claws to install the 2 rear seat headrest supports.



    B230028
  1. Engage the 4 claws to install the 2 rear seat center headrest supports.



    B309267E01
  1. Engage the 4 claws to install the rear seat shoulder belt hole cover as shown in the illustration.



    B230024
  1. Engage the 2 claws to install the seat belt anchor cover cap.



    B230022
  1. Using hog ring pliers, install 16 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover RH.



    B230020
  1. Engage the 6 clips.

  1. Install the 3 clips.



14. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY (w/ Center Armrest)


    B158420
  1. Install the bush.



    B230033
  1. Insert the pin into the rear seatback.

  1. Install the rear seat center armrest assembly with the bolt and bush.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



15. INSTALL CENTER ARMREST HINGE COVER (w/ Center Armrest)


    B230032
  1. Engage the claw to install the center armrest hinge cover as shown in the illustration.



16. INSTALL REAR SEATBACK STOP BUTTON GROMMET


    B230027
  1. Engage the 3 claws to install the rear seatback stop button grommet.



17. INSTALL REAR SEAT SHOULDER BELT GUIDE RH


    B230023
  1. Engage the guide to install the rear seat shoulder belt guide RH with the 2 screws.



18. INSTALL REAR SEATBACK COVER RH


    B230018
  1. Engage the 4 claws to install the rear seatback cover RH.



19. INSTALL REAR SEATBACK CENTER COVER


    B230019
  1. Engage the 4 claws to install the rear seatback center cover.