THROTTLE BODY > INSTALLATION |
| 1. INSTALL THROTTLE BODY ASSEMBLY |
Type A:
![]() |
Install a new gasket onto the intake manifold.
| *a | Protrusion |
![]() |
Install the throttle body assembly with the 2 bolts and 2 nuts.
Connect the No. 1 water by-pass hose and No. 2 water by-pass hose.
Connect the connector.
Type B:
![]() |
Install a new gasket onto the intake manifold.
| *a | Protrusion |
Install the throttle body assembly with the 4 bolts.
Connect the No. 1 water by-pass hose and No. 2 water by-pass hose.
Connect the connector.
| 2. INSTALL AIR CLEANER HOSE ASSEMBLY |
![]() |
Install the air cleaner hose assembly and tighten the hose clamp.
Connect the ventilation hose to the cylinder head cover sub-assembly.
| 3. INSTALL AIR CLEANER CASE |
![]() |
Install the air cleaner case with the 3 bolts.
Install the hose to the 3 clamps.
Install the air cleaner filter element sub-assembly.
| 4. INSTALL INLET AIR CLEANER ASSEMBLY |
![]() |
Install the inlet air cleaner assembly with the 2 bolts.
| 5. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Install the air cleaner cap sub-assembly with the 2 clamps.
Connect the air cleaner hose assembly and tighten the hose clamp.
![]() |
Connect the connector.
| 6. ADD ENGINE COOLANT (for Engine) |
Tighten the radiator drain cock plug.
Remove the reservoir tank cap.
![]() |
Add coolant to B line of the reservoir tank.
| *1 | B Line |
| Item | Capacity |
| Engine coolant | w/ Exhaust Heat Recirculation System: 7.2 liters (7.6 US qts, 6.3 lmp. qts) |
| w/o Exhaust Heat Recirculation System: 6.5 liters (6.8 US qts, 5.7 lmp. qts) |
Squeeze the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the reservoir tank cap.
Put the engine in inspection mode (Click here).
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.
Squeeze the inlet and outlet radiator hoses several times by hand to bleed air from the system.
![]() |
After the engine has cooled down, check that the coolant level is between full and low.
| *1 | Full Line |
| *2 | Low Line |
| 7. INSPECT FOR COOLANT LEAK (for Engine) |
Remove the reservoir tank cap.
![]() |
Fill the radiator and reservoir with coolant, and then attach a radiator cap tester.
Put the engine in inspection mode (Click here).
Warm up the engine.
Using the reservoir cap tester, increase the pressure inside the radiator to 108 kPa (1.1 kgf/cm2, 16 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator, front exhaust pipe assembly and the heater hose around and engine water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
Remove the radiator cap tester.
Install the reservoir tank cap.
| 8. INSTALL NO. 2 CYLINDER HEAD COVER |
![]() |
Engage the 3 clips to install the cover.
| 9. INSTALL NO. 1 ENGINE UNDER COVER |
| 10. PERFORM INITIALIZATION |
Connect the Techstream to the DLC3 and clear the DTCs (Click here).
Perform "Inspection After Repair" (Click here).
Set the vehicle to the inspection mode (Click here).
Start the engine without operating the accelerator pedal and check that the MIL is not illuminated and that the idle speed is within the specified range when the air conditioning is switched off after the engine is warmed up.
| Condition | Engine Idle Speed |
| A/C switched off | 950 to 1050 rpm |
Perform a road test and confirm that there are no abnormalities.