Home › Vehicle Exterior › WINDOW / GLASS › FRONT SIDE FIX WINDOW GLASS

FRONT SIDE FIX WINDOW GLASS > INSTALLATION

for Preparation Click here



1. CLEAN FRONT SIDE FIX WINDOW ASSEMBLY


    BO04421
  1. Clean the outer edges of the front side fix window assembly with a non-residue solvent.

    NOTICE:
    1. Do not touch the glass surface after cleaning it.
    2. Be careful not to damage the glass or clips.



2. INSTALL FRONT SIDE FIX WINDOW ASSEMBLY


  1. Using a brush or a sponge, apply Primer M to the exposed part of the vehicle body.


    B229143E01


    Text in Illustration 
    *1
    Brush
    *2
    Primer M
    *3
    Adhesive
    *4
    Edge of Curved Surface

    Standard Dimension:
    Item
    Dimension
    a
    25 mm (0.984 in.) or more

    NOTICE:
    1. Do not coat the adhesive with Primer M.
    2. Do not apply too much primer.
    3. Allow the primer to dry for 3 minutes or more.
    4. Throw away any leftover primer.



  1. Using a brush or a sponge, apply Primer G to the contact surface of the front side fix window assembly.


    B229144E01


    Text in Illustration 
    *1
    Edge of Curved Surface
    -
    -

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a non-residue solvent before it dries.

    NOTICE:
    1. To prevent the glass from breaking at low temperatures, ensure that no primer adheres to the contact surface between the moulding and glass during application.
    2. Allow the primer to dry for 3 minutes or more.
    3. Throw away any leftover primer.
    4. Do not apply too much primer.



  1. Apply adhesive to the front side fix window assembly.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent




      B214800E01
    1. Cut off the tip of the cartridge nozzle as shown in the illustration.

      Standard Dimension:
      Item
      Dimension
      a
      6.0 mm (0.236 in.)
      d
      8.0 mm (0.315 in.)

    2. Load the sealer gun with the cartridge.



    3. Apply adhesive to the front side fix window assembly as shown in the illustration.


      B229145E01



  1. Install the front side fix window assembly to the vehicle body.



      B229140E01
    1. Position the front side fix window assembly so that the matchmarks are aligned, and press it in gently along the rim (when a window with missing clips is used).
      Text in Illustration 
      *1
      Matchmark

    2. Lightly press the front side fix window assembly to ensure that the front side fix window assembly is securely fit to the vehicle body (when a window with missing clips is used).

      HINT:
      Press the glass with a force of 98 N (10 kgf, 22 lbf) or more.



    3. B229142
    4. Engage the 3 clips to install the front side fix window assembly (when a window without missing clips is used).

    5. Hold the front side fix window assembly in place securely with protective tape or equivalent until the adhesive hardens.

      NOTICE:
      1. Allow the primer to dry for 3 minutes or more.
      2. Check that the clips are attached to the body correctly.
      3. Check the clearance between the body and glass.

    6. Lightly press the outer surface of the glass to ensure that the glass is securely fit to the vehicle body.



    7. BO03986E05
    8. Using a scraper, remove any excess or protruding adhesive.

      HINT:
      Apply adhesive onto the glass rim.

      NOTICE:
      Do not drive the vehicle within the time described in the table below.

      Minimum Time:
      Temperature
      Minimum Time prior to Driving Vehicle
      35°C (95°F)
      1 hour and 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours



3. INSPECT FOR LEAK AND REPAIR
  1. After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.

  1. If water leaks into the cabin, allow the water to dry and add adhesive.

  1. Remove the protective tape.



4. INSTALL FRONT PILLAR GARNISH CORNER PIECE


    B223475
  1. Engage the 3 claws to install the front pillar garnish corner piece LH.



5. INSTALL FRONT PILLAR GARNISH


    B227780E01
  1. Remove the protective cover.
    Text in Illustration 
    *1
    Adhesive Tape
    *2
    Protective Cover
    *3
    Curtain Shield Airbag Assembly



    B257020E01
  1. Make sure that the front pillar garnish clip is not damaged.
    Text in Illustration 
    *1
    Front Pillar Garnish Clip
    *2
    Protective Tape

    NOTICE:
    1. If there is any damage, replace the garnish clip with a new one.
    2. When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.

  1. Engage the claw to direction indicated by the arrow (1).

  1. Engage the 3 guides to direction indicated by the arrow (2).

  1. Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish LH.

    HINT:
    Tape the needle-nosed pliers tip before use.



    B257025
  1. Engage the 2 clips to install the front pillar garnish LH.



6. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP


    B227774E01
  1. Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
    Text in Illustration 
    *1
    Alignment Mark (Yellow)

    NOTICE:
    After installation, check that the corners fit correctly.