Home › Vehicle Exterior › WINDOW / GLASS › FRONT SIDE FIX WINDOW GLASS

FRONT SIDE FIX WINDOW GLASS > REMOVAL

for Preparation Click here


HINT:
  1. The front side fix window assembly can be reused. When installing the window, if any of the clips on the front side fix window assembly are broken, butyl tape can be used to support the glass until the applied adhesive hardens.
  2. When using butyl tape to temporarily secure the window, make sure that the butyl tape is not applied exactly at the original clip location. If the butyl tape is applied exactly at the clip location, it will cause the window to protrude.
  3. Use the same procedure for the RH side and LH side.
  4. The procedure listed below is for the LH side.



1. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP
  1. Remove the front part of the front door opening trim weatherstrip to the extent that allows removal of the front pillar garnish.



2. REMOVE FRONT PILLAR GARNISH


    B257021
  1. When removing the front pillar garnish LH, cover the shaded part in the illustration with a piece of cloth so that the interior parts will not be damaged.



    B257024E01
  1. Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
    Text in Illustration 
    *1
    Front Pillar Garnish Clip

    HINT:
    Make the front pillar garnish LH hang down from the front pillar garnish clip.



    B257019E01
  1. Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish LH.

    NOTICE:
    1. Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.
    2. Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

    HINT:
    Tape the needle-nosed pliers tip before use.
    Text in Illustration 
    *1
    Protective Tape

  1. Disengage the 3 guides.



    B257022E01
  1. Disengage the claw while pressing the shaded part in the illustration in the direction indicated by the arrow (1).

  1. Remove the front pillar garnish LH by pulling it in the direction indicated by the arrow (2) in the illustration.



    B227780E01
  1. Protect the curtain shield airbag assembly.
    Text in Illustration 
    *1
    Adhesive Tape
    *2
    Protective Cover
    *3
    Curtain Shield Airbag Assembly

    1. Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



3. REMOVE FRONT PILLAR GARNISH CORNER PIECE


    B223474
  1. Disengage the 3 claws and front pillar garnish corner piece LH as shown in the illustration.



4. REMOVE FRONT SIDE FIX WINDOW ASSEMBLY


    B229139E01
  1. Apply protective tape to the installation position of the front side fix window assembly on the vehicle body.
    Text in Illustration 
    *1
    Protective Tape



    B229140E01
  1. Place matchmarks on the front side fix window assembly and vehicle body on the locations indicated in the illustration.
    Text in Illustration 
    *1
    Matchmark

    HINT:
    Matchmarks are not necessary if the front side fix window assembly is not going to be reused.



    B290466E01
  1. Cut off the clip at the location shown in the illustration.
    Text in Illustration 
    *a
    Cut Off



    B290468E01
  1. Pass a piano wire between the interior vehicle body and glass from the interior as shown in the illustration.
    Text in Illustration 
    *1
    Piano Wire
    *2
    Front Fender Extension

    HINT:
    Make sure the piano wire does not catch on the body side front fender extensions.

  1. Tie both wire ends to wooden blocks or similar objects that can serve as handles.

    NOTICE:
    When separating the front side fix window assembly from the vehicle, be careful not to damage the paint or interior and exterior ornaments.

  1. Cut off the adhesive by pulling the piano wire around the front side fix window assembly.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.



    B290469
  1. Disengage the 2 clips.

  1. Using suction cups, remove the glass.

    NOTICE:
    Be careful not to drop the glass.



5. CLEAN VEHICLE BODY


    B106081E15
  1. Clean and shape the contact surfaces of the vehicle body.
    Text in Illustration 
    *1
    Adhesive
    *2
    Vehicle Body

    1. Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body as shown in the illustration.

      NOTICE:
      Be careful not to damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

  1. Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.

    HINT:
    Even if all the adhesive has been removed, clean the vehicle body.