Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE

NAME PLATE > INSTALLATION

for Preparation Click here


HINT:
When installing new name plates or emblems, heat the vehicle body and name plates using a heat light.

Heating Temperature 
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Name Plate or emblem
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body, name plates or emblems excessively.



1. INSTALL LUGGAGE COMPARTMENT DOOR EMBLEM


    B229369E01
  1. Install the luggage compartment door emblem with the pin and 3 claws.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the vehicle body.



2. INSTALL NO. 2 BACK DOOR NAME PLATE
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove any double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Clean the No. 2 back door name plate (if reusing the No. 2 back door name plate).

    1. Using a heat light, heat the No. 2 back door name plate.

    2. Remove the double-sided tape from the No. 2 back door name plate.

    3. Wipe off any tape adhesive residue with cleaner.

    4. Apply new double-sided tape to the No. 2 back door name plate.



  1. Install the No. 2 back door name plate.

    1. Using a heat light, heat the vehicle body and the No. 2 back door name plate.

    2. Remove the release paper from the No. 2 back door name plate.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.



    3. Install the No. 2 back door name plate as shown in the illustration.


      B229373E01


      Text in Illustration 
      *1
      Location Pin
      -
      -



3. INSTALL BACK DOOR NAME PLATE
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove any double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Clean the back door name plate (if reusing the back door name plate).

    1. Using a heat light, heat the back door name plate.

    2. Remove the double-sided tape from the back door name plate.

    3. Wipe off any tape adhesive residue with cleaner.

    4. Apply new double-sided tape to the back door name plate.



  1. Install the back door name plate.

    1. Using a heat light, heat the vehicle body and the back door name plate.

    2. Remove the release paper from the back door name plate.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.



    3. Install the back door name plate as shown in the illustration.


      B229377E01


      Text in Illustration 
      *1
      Location Pin
      -
      -



4. INSTALL SIDE PANEL EMBLEM
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove any double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Clean the side panel emblem (if reusing the side panel emblem).

    1. Using a heat light, heat the side panel emblem.

    2. Remove the double-sided tape from the side panel emblem.

    3. Wipe off any tape adhesive residue with cleaner.

    4. Apply new double-sided tape to the side panel emblem.



  1. Install the side panel emblem.

    1. Using a heat light, heat the vehicle body and the side panel emblem.

    2. Remove the release paper from the side panel emblem.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.



    3. Install the side panel emblem as shown in the illustration.


      B229365E01


      Text in Illustration 
      *1
      Location Pin
      -
      -

      HINT:
      Use the same procedure for the RH side and LH side.