Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER

FRONT BUMPER > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY LH


    B228467
  1. Engage the guide and install the front side member bracket sub-assembly LH.

  1. Install the 4 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



2. INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side.



3. INSTALL FRONT BUMPER SIDE SUPPORT LH


    B294753E01
  1. Engage the 2 claws and install the front bumper side support LH.
    Text in Illustration 
    *1
    Bolt
    *2
    Screw

  1. Install the bolt and screw.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



4. INSTALL FRONT BUMPER SIDE SUPPORT RH

HINT:
Use the same procedure for the RH side and LH side.



5. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY


    B299344
  1. Engage the claw.

  1. Install the front bumper reinforcement sub-assembly with the 6 bolts.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }

  1. Engage the 7 clamps.



6. INSTALL FRONT BUMPER ENERGY ABSORBER


    B299343
  1. Engage the 2 guides to install the front bumper energy absorber.



7. INSTALL NO. 1 LOWER RADIATOR GRILLE


    B294749
  1. Engage the 20 claws to install the No. 1 lower radiator grille.

  1. Install the 2 outside moulding retainers.



8. INSTALL NO. 2 LOWER RADIATOR GRILLE


    B294748
  1. Engage the pin and 5 claws, and install the No. 2 lower radiator grille.



    B294747
  1. Install the 2 screws.



9. INSTALL FRONT BUMPER HOLE COVER LH


    B294746E01
  1. Engage the hook.
    Text in Illustration 
    *1
    Hook

  1. Engage the 3 claws and install the front bumper hole cover LH.



10. INSTALL FRONT BUMPER HOLE COVER RH

HINT:
Use the same procedure for the RH side and LH side.



11. INSTALL FRONT FENDER LINER RETAINER


    B228446
  1. Engage the claw and install the front fender liner retainer.

    HINT:
    Use the same procedure for the RH side and LH side.



12. INSTALL RADIATOR GRILLE EMBLEM ASSEMBLY


    B228461
  1. Engage the 2 pins and 4 claws, and install the radiator grille emblem assembly.

  1. Install the 2 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



13. INSTALL RADIATOR GRILLE


    B294743
  1. Engage the 12 claws and install the radiator grille.



    B294742
  1. Install the 4 clips.



14. INSTALL HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)


    B299342
  1. Engage the 8 clamps and install the headlight cleaner hose.



15. INSTALL ENGINE ROOM NO. 3 WIRE


  1. w/o Fog Light:



      B299341
    1. Engage the 7 clamps to install the engine room No. 3 wire.



  1. w/ Fog Light:



      B294741
    1. Engage the 9 clamps to install the engine room No. 3 wire.



16. INSTALL HOOD TO FRONT END PANEL SEAL


    B294740E01
  1. Engage the 2 clips and install the new hood to front end panel seal.
    Text in Illustration 
    *1
    Double-sided Tape

  1. Install the clip.



17. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET


    B299340
  1. Engage the 2 claws.

  1. Install the front bumper extension mounting bracket with the 2 screws.



18. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)
  1. Engage the 2 guides to temporarily install the fog light assembly.

  1. Install the fog light assembly with the screw.

    Torque:
    2.3 N*m{ 23 kgf*cm , 20 in.*lbf }

  1. Connect the connector.



19. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedure for the RH side and LH side.



20. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY LH (w/o Daytime Running Light)


    E238380
  1. Engage the 2 claws to temporarily install the front turn signal light assembly.

  1. Install the front turn signal light assembly with the clip.

  1. Engage each clamp.

  1. Connect the connector.



21. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY RH (w/o Daytime Running Light)

HINT:
Use the same procedure for the RH side and LH side.



22. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY LH (w/ Daytime Running Light)


    E238384
  1. Engage the 2 claws to temporarily install the front turn signal light assembly.

  1. Install the front turn signal light assembly with the clip.

  1. Engage each clamp.

  1. Connect the connector.



23. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY RH (w/ Daytime Running Light)

HINT:
Use the same procedure for the RH side and LH side.



24. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)


    E239914E01
  1. Pushing the tab and engage the 2 claws to install the headlight washer actuator sub-assembly LH.
    Text in Illustration 
    *1
    Tab



    E239912E01
  1. Push up the No. 1 headlight cleaner clamp.
    Text in Illustration 
    *1
    No. 1 Headlight Cleaner Clamp



    E239910E01
  1. Install the No. 3 headlight cleaner clamp.
    Text in Illustration 
    *1
    No. 3 Headlight Cleaner Clamp
    *2
    Headlight Cleaner Hose

  1. Connect the headlight cleaner hose.



25. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure for the RH side and LH side.



26. INSTALL HEADLIGHT CLEANER WASHER NOZZLE COVER (w/ Headlight Cleaner System)


    E239908
  1. Engage the 2 claws to install the headlight cleaner washer nozzle cover.

    HINT:
    Use the same procedure for the RH side and LH side.