Home › Vehicle Interior › DOOR LOCK › DOOR CONTROL RECEIVER

DOOR CONTROL RECEIVER > INSTALLATION

for Preparation Click here



1. INSTALL DOOR CONTROL RECEIVER


    B229270
  1. Install the door control receiver with the bolt.

    Torque:
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf }

  1. Connect the connector.



2. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side .



3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
  1. Engage the 7 claws and 2 clips.



  1. Install the deck trim side panel assembly RH with the screw.


    B227803



4. INSTALL TONNEAU COVER HOLDER CAP

HINT:
Use the same procedure for the RH side and LH side .



5. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY

HINT:
Use the same procedure for the RH side and LH side .



6. INSTALL REAR DECK TRIM COVER


    B227796
  1. Engage the 4 claws and 4 guides to install the rear deck trim cover.



7. INSTALL DECK TRIM SERVICE HOLE COVER


    B227795
  1. Engage the 3 guides.

  1. Engage the 2 claws to install the deck trim service hole cover.



8. INSTALL REAR NO. 1 FLOOR BOARD


    B227794
  1. Engage the 2 claws and 2 clips.

  1. Install the rear No. 1 floor board with the bolt.



9. INSTALL REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY


    B227793
  1. Engage the claw and 2 clips to install the rear No. 2 floor board sub-assembly.



10. INSTALL REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY


    B227792
  1. Engage the 2 claws and 2 clips to install the rear No. 1 floor board sub-assembly.



11. INSTALL REAR NO. 3 FLOOR BOARD


    B227791
  1. Engage the 2 guides to install the rear No. 3 floor board.



12. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Install the tonneau cover assembly.



13. INSTALL REAR SEAT CUSHION ASSEMBLY


    B311726E01
  1. Engage the 2 guides of the seat cushion to the seatback.
    Text in Illustration 
    *1
    Guide
    *2
    Hook

  1. Engage the 2 front hooks of the seat cushion to the vehicle body.

    NOTICE:
    When installing the seat cushion, make sure that the seat belt buckle is not under the seat cushion.

    HINT:
    Confirm that the seat cushion is firmly installed.



14. INSTALL REAR SIDE SEATBACK ASSEMBLY RH


    B230046
  1. Engage the 2 guides as shown in the illustration.

  1. Install the rear side seatback assembly RH with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



15. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B227771E01
  1. Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
    Text in Illustration 
    *1
    Alignment Mark (Blue)

    NOTICE:
    After installation, check that the corners fit correctly.



16. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and LH side .



17. INSTALL REAR DECK FLOOR BOX
  1. Install the rear deck floor box.



18. INSTALL REAR NO. 2 FLOOR BOARD (for Separate Type)


    B227788E01
  1. Engage the 3 guides <A>.

  1. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.