Home › Vehicle Interior › LIGHTING (INT) › REAR DOOR COURTESY SWITCH

REAR DOOR COURTESY SWITCH > INSTALLATION

for Preparation Click here



1. INSTALL REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY


    E189724
  1. Using a T30 "TORX" socket wrench, install the rear door courtesy light switch assembly with the bolt.

    Torque:
    6.3 N*m{ 64 kgf*cm , 56 in.*lbf }

  1. Connect the connector.



2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)
  1. Connect the connector.

  1. Engage the 7 claws and 2 clips.



  1. Install the deck trim side panel assembly LH with the screw.


    B227804



3. INSTALL TONNEAU COVER HOLDER CAP (for LH Side)


    B227801
  1. Engage the claw to install the tonneau cover holder cap.



4. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)


    B227798
  1. Engage the 2 guides.

  1. Install the 2 luggage hold belt striker assemblies with the 2 bolts.



5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)
  1. Engage the 7 claws and 2 clips.



  1. Install the deck trim side panel assembly RH with the screw.


    B227803



6. INSTALL TONNEAU COVER HOLDER CAP (for RH Side)

HINT:
Use the same procedure described for the LH side.



7. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

HINT:
Use the same procedure described for the LH side.



8. INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for LH Side)


    B230043
  1. Engage the 2 guides as shown in the illustration.

  1. Install the rear side seatback assembly LH with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



9. INSTALL REAR SIDE SEATBACK ASSEMBLY RH (for RH Side)

HINT:
Use the same procedure described for the LH side.



10. INSTALL REAR SEAT CUSHION ASSEMBLY


    B311726E01
  1. Engage the 2 guides of the seat cushion to the seatback.
    Text in Illustration 
    *1
    Guide
    *2
    Hook

  1. Engage the 2 front hooks of the seat cushion to the vehicle body.

    NOTICE:
    When installing the seat cushion, make sure that the seat belt buckle is not under the seat cushion.

    HINT:
    Confirm that the seat cushion is firmly installed.



11. INSTALL REAR DECK TRIM COVER


    B227796
  1. Engage the 4 claws and 4 guides to install the rear deck trim cover.



12. INSTALL DECK TRIM SERVICE HOLE COVER


    B227795
  1. Engage the 3 guides.

  1. Engage the 2 claws to install the deck trim service hole cover.



13. INSTALL REAR NO. 1 FLOOR BOARD


    B227794
  1. Engage the 2 claws and 2 clips.

  1. Install the rear No. 1 floor board with the bolt.



14. INSTALL REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY


    B227793
  1. Engage the claw and 2 clips to install the rear No. 2 floor board sub-assembly.



15. INSTALL REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY


    B227792
  1. Engage the 2 claws and 2 clips to install the rear No. 1 floor board sub-assembly.



16. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Install the tonneau cover assembly.



17. INSTALL DECK FLOOR BOX LH (for LH Side)


    B227790
  1. Engage the 2 guides.

  1. Install the deck floor box LH with the clip.



18. INSTALL REAR NO. 4 FLOOR BOARD (for LH Side)


    B227789
  1. Engage the guide to install the rear No. 4 floor board.



19. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP


    B227772E01
  1. Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
    Text in Illustration 
    *1
    Alignment Mark (Red)

    NOTICE:
    After installation, check that the corners fit correctly.



20. INSTALL REAR DOOR SCUFF PLATE


    B227766
  1. Engage the 7 claws to install the rear door scuff plate LH.



21. INSTALL REAR NO. 3 FLOOR BOARD (for RH Side)


    B227791
  1. Engage the 2 guides to install the rear No. 3 floor board.



22. INSTALL REAR DECK FLOOR BOX
  1. Install the rear deck floor box.



23. INSTALL REAR NO. 2 FLOOR BOARD (for Separate Type)


    B227788E01
  1. Engage the 3 guides <A>.

  1. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.