REAR DOOR COURTESY SWITCH > REMOVAL |
| 1. REMOVE REAR NO. 2 FLOOR BOARD (for Separate Type) |
![]() |
Disengage the 2 guides <A> as shown in the illustration.
Disengage the 3 guides <B> and remove the rear No. 2 floor board.
| 2. REMOVE REAR DECK FLOOR BOX |
Remove the rear deck floor box.
| 3. REMOVE REAR NO. 3 FLOOR BOARD (for RH Side) |
![]() |
Disengage the 2 guides and remove the rear No. 3 floor board.
| 4. REMOVE REAR NO. 4 FLOOR BOARD (for LH Side) |
![]() |
Disengage the guide and remove the rear No. 4 floor board.
| 5. REMOVE DECK FLOOR BOX LH (for LH Side) |
![]() |
Remove the clip.
Disengage the 2 guides and remove the deck floor box LH.
| 6. REMOVE REAR DOOR SCUFF PLATE |
![]() |
Disengage the 7 claws and remove the rear door scuff plate LH.
| 7. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP |
![]() |
Remove the rear door opening trim weatherstrip LH.
| 8. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Remove the tonneau cover assembly.
| 9. REMOVE REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY |
![]() |
Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board sub-assembly.
| 10. REMOVE REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY |
![]() |
Disengage the claw and 2 clips, and remove the rear No. 2 floor board sub-assembly.
| 11. REMOVE REAR NO. 1 FLOOR BOARD |
![]() |
Remove the bolt.
Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board.
| 12. REMOVE DECK TRIM SERVICE HOLE COVER |
![]() |
Disengage the 2 claws and 3 guides, and remove the deck trim service hole cover.
| 13. REMOVE REAR DECK TRIM COVER |
![]() |
Disengage the 4 claws and 4 guides, and remove the rear deck trim cover.
| 14. REMOVE REAR SEAT CUSHION ASSEMBLY |
![]() |
Disengage the 2 front hooks of the seat cushion from the vehicle body as shown in the illustration.
| *1 | Hook |
| *2 | Guide |
| *a | 100 mm (3.94 in.) or less |
Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.
Repeat the above procedure for the other hook.
Disengage the 2 guides of the seat cushion from the seatback.
Remove the rear seat cushion assembly.
| 15. REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for LH Side) |
![]() |
Remove the bolt.
![]() |
Disengage the 2 guides and remove the rear side seatback assembly LH as shown in the illustration.
| 16. REMOVE REAR SIDE SEATBACK ASSEMBLY RH (for RH Side) |
| 17. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side) |
![]() |
Remove the 2 bolts.
Disengage each guide and remove the 2 luggage hold belt striker assemblies.
| 18. REMOVE TONNEAU COVER HOLDER CAP (for LH Side) |
![]() |
Using a screwdriver, disengage the claw and remove the tonneau cover holder cap.
| *1 | Protective Tape |
| 19. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side) |
Remove the screw.
Disengage the 7 claws and 2 clips.
Disconnect the connector and remove the deck trim side panel assembly LH.

| 20. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side) |
| 21. REMOVE TONNEAU COVER HOLDER CAP (for RH Side) |
| 22. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side) |
Remove the screw.
Disengage the 7 claws and 2 clips, and remove the deck trim side panel assembly RH.

| 23. REMOVE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY |
Disconnect the connector.
![]() |
Using a T30 "TORX" socket wrench, remove the bolt and rear door courtesy light switch assembly.