Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0069-273    Manifold Absolute Pressure - Barometric Pressure Correlation

for Preparation Click here


DESCRIPTION

The atmospheric pressure sensor mounted on the MG ECU circuit board detects the atmospheric pressure. This reading is used to perform system control that considers vehicle usage conditions.

A220063E01


DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0069
273
Difference between the pressure value of the atmosphere pressure sensor in the inverter with converter assembly and the manifold absolute pressure sensor assembly exceeds a specified value and the same condition recurs after 3 hours or more when driving in EV drive mode.
(1 trip detection logic)
  1. Inverter with converter assembly
  2. Manifold absolute pressure sensor
  3. ECM
  4. Wire harness or connector

Related Data List 
DTC No.
Data List
P0069-273
  1. MAP
  2. Atmosphere Pressure

INSPECTION PROCEDURE

HINT:
After the repair, perform the following procedure to confirm the repair.
  1. If the values of Data List items "Atmosphere Pressure" and "MAP" are almost the same with the engine stopped and the power switch on (IG), those sensors are normal.

1.CHECK DTC OUTPUT (ENGINE CONTROL)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (READY).

  1. Fully depress the accelerator pedal for 5 seconds to start the engine and keep it running.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    Except the following.
    A
    Any of the following DTCs are also output.
    B


    DTC No.
    Relevant Diagnosis
    P0107
    Manifold Absolute Pressure/Barometric Pressure Circuit Low Input
    P0108
    Manifold Absolute Pressure/Barometric Pressure Circuit High Input
    P106A
    Evaporative Emission System Pressure Sensor - Manifold Absolute Pressure Correlation

    HINT:
    P0069-273 may be output due to a malfunction which causes the DTCs in the preceding table to be output. In this case, first troubleshoot the output DTCs in the preceding table.

  1. Turn the power switch off.



B
GO TO DTC CHART (Click here)
A


2.CHECK DTC OUTPUT (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P0069-273 only is output or DTCs except the ones in the table below are also output.
    A
    Any of the following DTCs are also output.
    B


    DTC No.
    Relevant Diagnosis
    P0A1A-151, 155, 156, 658, 659
    Generator Control Module
    P0A1B-193, 512, 661, 786
    Drive Motor "A" Control Module
    P0A1D-148
    Hybrid Powertrain Control Module
    P2228-268
    Barometric Pressure Sensor "A" Circuit Low
    P2229-269
    Barometric Pressure Sensor "A" Circuit High
    P2511-149
    HV CPU Power Relay Sense Circuit Intermittent No Continuity
    P324E-788
    MG-ECU Power Relay Intermittent Circuit
    U0100-211, 530
    Lost Communication with ECM/PCM "A"
    U0110 (all INF codes)*1
    Lost Communication with Drive Motor Control Module "A"

    HINT:
    1. *1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.
    2. P0069-273 may be output due to a malfunction which causes the DTCs in the preceding table to be output. In this case, first troubleshoot the output DTCs in the preceding table.

  1. Turn the power switch off.



B
GO TO DTC CHART (Click here)
A


3.READ VALUE USING TECHSTREAM (MAP, ATMOSPHERE PRESSURE)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / MAP, Atmosphere Pressure.



  1. Using the table, read the "normal atmospheric pressure value" for the applicable altitude.


    A250945

    HINT:
    1. Standard atmospheric pressure is approximately 101 kPa.
    2. For every 100 m (328 ft) increase in altitude, atmospheric pressure drops by approximately 1 kPa (7.5 mmHg).
    3. The actual atmospheric pressure also varies by weather.

  1. Compare the MAP and Atmosphere Pressure values in the Data List with the normal atmospheric value from the table.

    Result:

    Result
    Proceed to
    Other than the following.
    A
    Difference between MAP in Data List and "normal atmospheric pressure value" is 10 kPa or more.
    B
    Difference between Atmosphere Pressure in Data List and "normal atmospheric pressure value" is 10 kPa or more.
    C

  1. Turn the power switch off.



B
Go to step 5

C
REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)
A


4.READ VALUE USING TECHSTREAM (MAP)
  1. Push the P position switch.

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / MAP

  1. Read the MAP value in the Data List with the engine stopped.

  1. While depressing the brake pedal, turn the power switch on (READY).

  1. With the READY indicator light illuminated, fully depress the accelerator pedal.

  1. Read the MAP value in the Data List with the engine running.

  1. Compare the MAP value noted with the engine stopped and the MAP value noted with the engine running.

    OK:
    The MAP value changes (pressure decreases when the engine is started).

  1. Turn the power switch off.



NG
Go to step 7
OK


5.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NEXT


6.READ VALUE USING TECHSTREAM (MAP, ATMOSPHERE PRESSURE)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / MAP, Atmosphere Pressure.

  1. Compare the Data List item "MAP" with "Atmosphere Pressure".

    Result:

    Result
    Proceed to
    The difference between "MAP" and "Atmosphere Pressure" is 10 kPa or more.
    A
    The difference between "MAP" and "Atmosphere Pressure" is less than 10 kPa.
    B

  1. Turn the power switch off.



B
COMPLETED
A

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)  

7.CHECK TERMINAL VOLTAGE (MANIFOLD ABSOLUTE PRESSURE SENSOR)
A209150E11
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D3-3 (VC) - D3-2 (E2)
    Power switch on (IG)
    4.75 to 5.25 V
    D3-1 (PIM) - D3-2 (E2)
    Power switch on (IG)
    3.0 to 5.0 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Manifold Absolute Pressure Sensor)

    Result:
    Result
    Proceed to
    Outside standard range
    A
    Within standard range
    B



B
Go to step 9
A


8.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    D3-3 (VC) - D28-72 (VCPM)
    Always
    Below 1 Ω
    D3-2 (E2) - D28-71 (EPIM)
    Always
    Below 1 Ω
    D3-1 (PIM) - D28-69 (PIM)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    D3-3 (VC) or D28-72 (VCPM) - Body ground
    Always
    10 kΩ or higher
    D3-1 (PIM) or D28-69 (PIM) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

9.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
  1. Replace the manifold absolute pressure sensor (Click here).


NEXT


10.CLEAR DTC
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Clear DTCs and freeze frame data.


NEXT


11.READ VALUE USING TECHSTREAM (MAP, ATMOSPHERE PRESSURE)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / MAP, Atmosphere Pressure.

  1. Compare the Data List item "MAP" with "Atmosphere Pressure".

    Result:

    Result
    Proceed to
    The difference between "MAP" and "Atmosphere Pressure" is less than 10 kPa.
    A
    The difference between "MAP" and "Atmosphere Pressure" is 10 kPa or more.
    B

  1. Turn the power switch off.



B
REPLACE ECM (Click here)
A

END