Home › Vehicle Interior › SEAT BELT › REAR CENTER SEAT OUTER BELT ASSEMBLY

REAR CENTER SEAT OUTER BELT ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL REAR CENTER SEAT BELT ASSEMBLY


    B221502E01
  1. Install the rear center seat belt assembly with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    Text in Illustration 
    *1
    Protruding Part

    NOTICE:
    Do not allow the rear center seat belt assembly to overlap the protruding part of the rear seat back frame.



2. INSTALL REAR SEATBACK COVER WITH PAD RH
  1. Temporarily install the rear seatback cover with pad RH to the rear seatback frame sub-assembly RH.



    B230030
  1. Engage the 4 claws to install the 2 rear seat headrest supports.



    B230028
  1. Engage the 4 claws to install the 2 rear seat center headrest supports.



    B309267E01
  1. Engage the 4 claws to install the rear seat shoulder belt hole cover as shown in the illustration.



    B230024
  1. Engage the 2 claws to install the seat belt anchor cover cap.



    B230022
  1. Using hog ring pliers, install 16 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover RH.



    B230020
  1. Engage the 6 clips.

  1. Install the 3 clips.



3. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY (w/ Center Armrest)


    B158420
  1. Install the bush.



    B230033
  1. Insert the pin into the rear seatback.

  1. Install the rear seat center armrest assembly with the bolt and bush.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



4. INSTALL CENTER ARMREST HINGE COVER (w/ Center Armrest)


    B230032
  1. Engage the claw to install the center armrest hinge cover as shown in the illustration.



5. INSTALL REAR SEATBACK STOP BUTTON GROMMET


    B230027
  1. Engage the 3 claws to install the rear seatback stop button grommet.



6. INSTALL REAR SEAT SHOULDER BELT GUIDE RH


    B230023
  1. Engage the guide to install the rear seat shoulder belt guide RH with the 2 screws.



7. INSTALL REAR SEATBACK COVER RH


    B230018
  1. Engage the 4 claws to install the rear seatback cover RH.



8. INSTALL REAR SEATBACK CENTER COVER


    B230019
  1. Engage the 4 claws to install the rear seatback center cover.



9. INSTALL REAR SEATBACK ASSEMBLY RH
  1. Place the rear seatback assembly RH in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Install the rear seatback assembly RH with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Engage the fastener.

  1. Raise the rear seatback assembly RH.



10. INSTALL REAR SEAT CENTER HEADREST ASSEMBLY
  1. Install the rear seat center headrest assembly.



11. INSTALL REAR SEAT HEADREST ASSEMBLY RH
  1. Install the rear seat headrest assembly RH.



12. CONNECT REAR CENTER SEAT BELT ASSEMBLY


    B221513E01
  1. Connect the anchor part of the rear seat inner belt assembly.
    Text in Illustration 
    *1
    Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear center seat belt assembly to overlap the protruding part of the rear seat inner belt assembly RH.



13. INSTALL REAR SEAT CUSHION ASSEMBLY


    B311726E01
  1. Engage the 2 guides of the seat cushion to the seatback.
    Text in Illustration 
    *1
    Guide
    *2
    Hook

  1. Engage the 2 front hooks of the seat cushion to the vehicle body.

    NOTICE:
    When installing the seat cushion, make sure that the seat belt buckle is not under the seat cushion.

    HINT:
    Confirm that the seat cushion is firmly installed.