Home › Engine / Hybrid System › 2ZR-FXE EMISSION CONTROL › EGR COOLER

EGR COOLER > INSTALLATION

for Preparation Click here



1. INSTALL EGR WITH COOLER PIPE SUB-ASSEMBLY


    A297470
  1. Temporarily install a new gasket and the EGR valve assembly to the EGR with cooler pipe sub-assembly with the 2 nuts.

  1. Install a new gasket and set the EGR valve with cooler assembly in place.



  1. Using an E8 "TORX" socket wrench, install the 4 stud bolts.


    A297489E04


    Text in Illustration 
    *a
    Stud Bolt A
    *b
    Stud Bolt B
    *c
    Stud Bolt C
    -
    -

    Torque:
    Stud Bolt A and Stud Bolt B:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
    Stud Bolt C:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    If a stud bolt is deformed or the threads are damaged, replace it.



  1. Temporarily install the 2 nuts (B), 2 nuts (C) and bolt.

    HINT:
    The type B and type C of the nut (C) is non-reusable.



    A307474E02


    Text in Illustration 
    *A
    Type A
    *B
    Type B
    *C
    Type C
    -
    -
    *a
    Nut A
    *b
    Nut B
    *c
    Nut C
    *d
    Bolt

  1. Tighten the 2 nuts (A).

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Tighten the 2 nuts (B) and bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Make sure that all installation surfaces of the EGR valve with cooler assembly are in even contact when tightening the bolt and nuts.

  1. Tighten the 2 nuts (C).

    Torque:
    Type A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    Type B:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }
    Type C:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



    A212666
  1. Connect the 4 water hoses to the EGR valve with cooler assembly and slide the 4 clips to secure them.

  1. Engage the wire harness clamp.

  1. Connect the EGR valve assembly connector.



2. INSTALL EGR PIPE ASSEMBLY


    A212665
  1. Install 2 new gaskets and EGR pipe assembly with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Make sure to tighten the 4 bolts evenly until the flanges of the EGR pipe assembly contact with the installation surfaces.



    A212664
  1. Install the wire harness support with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A212663
  1. Engage the 2 wire harness clamps.



3. INSTALL AIR CLEANER CASE


    A212314
  1. Install the air cleaner case with the 3 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Install the hose to the 3 clamps.

  1. Install the air cleaner filter element sub-assembly.



4. INSTALL INLET AIR CLEANER ASSEMBLY


    A269507
  1. Install the inlet air cleaner assembly with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



5. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    A288960
  1. Install the air cleaner cap sub-assembly with the 2 clamps.

  1. Connect the air cleaner hose assembly and tighten the hose clamp.



    A212311
  1. Connect the connector.



6. INSTALL NO. 2 CYLINDER HEAD COVER


    A213020
  1. Engage the 3 clips to install the cover.

    NOTICE:
    1. Be sure to engage the clips securely.
    2. Do not apply excessive force or hit the cover to engage the clips. This may cause the cover to break.



7. ADD COOLANT (for Engine)
  1. Tighten the radiator drain cock plug.

  1. Remove the reservoir tank cap.



    A213418E01
  1. Add coolant to B line of the reservoir tank.
    Text in Illustration 
    *1
    B Line

    Standard Capacity:
    Item
    Capacity
    Engine coolant
    w/ Exhaust Heat Recirculation System:
    7.2 liters (7.6 US qts, 6.3 lmp. qts)
    w/o Exhaust Heat Recirculation System:
    6.5 liters (6.8 US qts, 5.7 lmp. qts)

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Squeeze the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the reservoir tank cap.

  1. Put the engine in inspection mode (Click here).

  1. Bleed air from the cooling system.

    NOTICE:
    1. Before starting the engine, turn the A/C switch off.
    2. Adjust the heater control to the maximum hot setting.
    3. Adjust the blower speed to low setting.


    1. Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.

      HINT:
      The thermostat opening timing can be confirmed by squeezing the inlet radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the hose.

      CAUTION:
      When squeezing the radiator hose:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

    2. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air from the system.

      CAUTION:
      When squeezing the radiator hose:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.



    A213418E02
  1. After the engine has cooled down, check that the coolant level is between full and low.
    Text in Illustration 
    *1
    Full Line
    *2
    Low Line
    If the coolant level is low, add coolant to the full line on the reservoir tank.



8. INSPECT FOR COOLANT LEAK (for Engine)

CAUTION:
Do not remove the reservoir tank cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch off.

  1. Remove the reservoir tank cap.



    A213419
  1. Fill the radiator and reservoir with coolant, and then attach a radiator cap tester.

  1. Put the engine in inspection mode (Click here).

  1. Warm up the engine.

  1. Using the reservoir cap tester, increase the pressure inside the radiator to 108 kPa (1.1 kgf/cm2, 16 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator, front exhaust pipe assembly and the heater hose around and engine water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.

  1. Remove the radiator cap tester.

  1. Install the reservoir tank cap.



9. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY


    C205669
  1. Install the outer cowl top panel sub-assembly with the 9 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    C205673
  1. Bend the water guard plate RH and engage the claw.



    C205671
  1. Bend the No. 1 heater air duct splash shield seal and engage the claw.



    C205668E01
  1. Engage the 2 clamps and guide to install the wire harness.
    Text in Illustration 
    *1
    Clamp
    *2
    Guide



10. INSTALL COWL BODY MOUNTING REINFORCEMENT LH


    C205667
  1. Install the cowl body mounting reinforcement LH with the 3 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



11. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
(Click here)