ROOF HEADLINING > REASSEMBLY |
| 1. INSTALL NO. 2 ROOF HEADLINING PAD |
Align the markings on the roof headlining assembly with the No. 2 roof headlining pad and install the pad using hot-melt glue as shown in the illustration.

| *1 | Hot-melt Glue | *2 | Marking |
| 2. INSTALL ROOF HEADLINING PAD |
Align the markings on the roof headlining assembly with the roof headlining pad and install the pad using hot-melt glue as shown in the illustration.

| *1 | Hot-melt Glue | *2 | Marking |
| 3. INSTALL NO. 2 ROOF HEADLINING SET PLATE RH (w/o Sliding Roof) |
Align the markings on the roof headlining assembly with the No. 2 roof headlining set plate RH and install the set plate using hot-melt glue as shown in the illustration.

| *1 | Hot-melt Glue | *2 | Marking |
| 4. INSTALL NO. 2 ROOF HEADLINING SET PLATE LH (w/o Sliding Roof) |
| 5. INSTALL NO. 1 ROOF WIRE |
Apply double-sided tape as shown in the illustration.
Peel off the release paper from the double-sided tape.
Attach the No. 1 roof wire along the double-sided tape so that the marking surface of the wire harness faces downward.

| *1 | Double-sided Tape | *2 | Marking |
Align the pink marking tape <A> on the vehicle front side on the No. 1 roof wire with the vehicle front side tab on the roof headlining, and apply adhesive tape.
Turn the visor connector RH clockwise approximately 45° to install the connector to the roof headlining assembly.
Align the pink marking tape <B> on the No. 1 roof wire with the markings on the roof headlining, and apply adhesive tape.
Engage each clamp.
Align the pink marking tape <C> on the No. 1 roof wire with the markings on the roof headlining, and apply adhesive tape.
Turn the visor connector LH clockwise approximately 45° to install the connector to the roof headlining assembly.
Attach the No. 1 roof wire, starting from the front of the vehicle, while aligning it with the double-side tape.
Apply adhesive tape by aligning it with the markings on the roof headlining.

| *1 | Adhesive Tape | *2 | Marking |
| *3 | Marking Line (White) | *4 | Adjustment Area |
| *5 | w/ EC Mirror | *6 | w/ Rain Sensor |
| 6. INSTALL NO. 4 ANTENNA CORD SUB-ASSEMBLY (w/o Manual (SOS) Switch) |
Peel off the release paper from one side of new double-sided tape and apply the new double-sided tape to the position indicated in the illustration. Be careful not to touch the adhesive surface.

| *A | w/o Sliding Roof | *B | w/ Sliding Roof |
| *1 | Double-sided Tape | - | - |
| *a | Front | *b | Double-sided Tape Size |
| Area | Dimension |
| X | 1.0 mm (0.0394 in.) |
| Y | 10.0 mm (0.394 in.) |
Peel off the release paper from the double-sided tape. Be careful not to touch the adhesive surface.
Align the vehicle front side marking (pink) on the No. 4 antenna cord sub-assembly with the vehicle front side tab on the roof headlining, and wrap the tape over the antenna cord to install it. (1)

| *A | w/o Sliding Roof | *B | w/ Sliding Roof |
| *1 | Tape | *2 | Extra Cord Storage Area |
| *a | Front | *b | Pink |
Temporarily install the front part of the No. 4 antenna cord sub-assembly (2) with the adhesive tape.
Temporarily install the front part of the No. 4 antenna cord sub-assembly (3) with the adhesive tape.
Temporarily install the No. 4 antenna cord sub-assembly by placing it on the double-sided tape from the front of the vehicle to the point just before the extra cord storage area.
Align the vehicle rear marking (pink) on the No. 4 antenna cord sub-assembly with the tape attachment location (scribe line) of the roof headlining, and wrap the tape over the antenna cord to install it. (4)
Temporarily install the rear side of the No. 4 antenna cord sub-assembly (5) with the adhesive tape.
Temporarily install the No. 4 antenna cord sub-assembly by placing it on the double-sided tape from the rear of the vehicle to the point just before the extra cord storage area.
![]() |
Using double-sided tape, place any excess No. 4 antenna cord sub-assembly in the extra cord storage area to finish installing the antenna cord.
| *1 | Extra Cord Storage Area |
| 7. INSTALL TELEPHONE AND GPS ANTENNA CORD SUB-ASSEMBLY (w/ Manual (SOS) Switch) |
Peel off the release paper from one side of new double-sided tape and apply the new double-sided tape to the position indicated in the illustration. Be careful not to touch the adhesive surface.

| Area | Dimension |
| X | 1.0 mm (0.0394 in.) |
| Y | 10.0 mm (0.394 in.) |

| Area | Dimension |
| X | 1.0 mm (0.0394 in.) |
| Y | 10.0 mm (0.394 in.) |
Peel off the release paper from the double-sided tape. Be careful not to touch the adhesive surface.
Align the vehicle front side marking (pink) on the telephone and GPS antenna cord sub-assembly with the vehicle front side tab on the roof headlining, and wrap the tape over the antenna cord to install it. (1)

Temporarily install the front side of the telephone and GPS antenna cord sub-assembly (2) with the adhesive tape.
Temporarily install the front side of the telephone and GPS antenna cord sub-assembly (3) with the adhesive tape.
Temporarily install the telephone and GPS antenna cord sub-assembly by placing it on the double-sided tape from the front of the vehicle to the point just before the extra cord storage area.
Align the vehicle rear marking (pink) on the telephone and GPS antenna cord sub-assembly with the tape attachment location (scribe line) of the roof headlining, and wrap the tape over the antenna cord to install it. (4)
Temporarily install the rear side of the telephone and GPS antenna cord sub-assembly (5) with the adhesive tape.
Temporarily install the telephone and GPS antenna cord sub-assembly by placing it on the double-sided tape from the rear of the vehicle to the point just before the extra cord storage area.
![]() |
Using double-sided tape, place any excess telephone and GPS antenna cord sub-assembly in the extra cord storage area to finish installing the antenna cord.
| 8. INSTALL NO. 3 ROOF SILENCER PAD (w/o Sliding Roof) |
Align the markings on the roof headlining assembly with the No. 3 roof silencer pad and install the set plate using hot-melt glue as shown in the illustration.

| *1 | Roof Silencer Pad Marking | *2 | Hot-melt Glue Marking |
| 9. INSTALL NO. 2 ROOF SILENCER PAD (w/o Sliding Roof) |
Align the markings on the roof headlining assembly with the No. 2 roof silencer pad and install the set plate using hot-melt glue as shown in the illustration.

| *1 | Roof Silencer Pad Marking | *2 | Hot-melt Glue Marking |
| 10. INSTALL VANITY LIGHT ASSEMBLY |
Install the vanity light assembly .