Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

DTC    B1503    Exhaust Heat Management Warning Detected

for Preparation Click here


DESCRIPTION

This DTC is stored when the combination meter assembly (No. 3 meter circuit plate) detects a malfunction in the water temperature sensor that is connected to the combination meter assembly (No. 3 meter circuit plate) via a direct line.

DTC No.
DTC Detection Condition
Trouble Area
B1503
When IG voltage is 9.5 V or more and the following condition is detected:
  1. Water temperature sensor operation malfunction
  2. Water temperature sensor circuit open or short
  3. Engine coolant temperature is 120°C (248°F) or more
  1. Harness or connector
  2. Water temperature sensor
  3. Combination meter assembly (No. 3 meter circuit plate)

HINT:
This DTC is for the water temperature sensor which is used to detect the engine water temperature sensor for the exhaust heat recirculation system, not for the engine coolant temperature sensor which is used for the EFI system.


WIRING DIAGRAM


E188188E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Set the vehicle in the maintenance mode using the Techstream (Click here).

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Combination Meter / Data List.

  1. Check the values by referring to the table below.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Coolant Temperature
    Engine coolant temperature/-40 to 127.5°C (-40 to 261.5°F)
    After warming up: 80 to 100°C (176 to 212°F)
    -

    HINT:
    1. The coolant temperature value in this inspection is the data sent from the engine coolant temperature sensor for the SFI system.
    2. When the Data List values do not match, a signal output error of the ECM is suspected.

    OK:
    Engine coolant temperature displayed on the Techstream is 80 to 100°C (176 to 212°F) after warming up.



NG
GO TO EXHAUST HEAT RECIRCULATION SYSTEM (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (NO. 3 METER CIRCUIT PLATE - WATER TEMPERATURE SENSOR)
  1. Disconnect the G2 connector.

  1. Disconnect the L27 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G2-2 (TWS3) - L27-16 (TWS3)
    Always
    Below 1 Ω
    G2-1 (E2) - L27-9 (E2)
    Always
    Below 1 Ω
    G2-2 (TWS3) or L27-16 (TWS3) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.WATER TEMPERATURE SENSOR


    E188251E01
  1. Remove the water temperature sensor (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (E2) - 2 (TWS3)
    Temperature is 20°C (68°F)
    2.32 to 2.59 kΩ
    1 (E2) - 2 (TWS3)
    Temperature is 80°C (176°F)
    0.310 to 0.326 kΩ

    Text in Illustration 
    *1
    Component without harness connected
    (Water Temperature Sensor)



NG
REPLACE WATER TEMPERATURE SENSOR (Click here)
OK

REPLACE COMBINATION METER ASSEMBLY (NO. 3 METER CIRCUIT PLATE) (Click here)