Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

DTC    B1504    Lost Communication with Steering SW

for Preparation Click here


DESCRIPTION

The combination meter assembly (No. 3 meter circuit plate) communicates with the multi-information switch (steering pad switch assembly) via a direct line . If the combination meter assembly (No. 3 meter circuit plate) detects a communication malfunction, it stores this DTC.

DTC No.
DTC Detection Condition
Trouble Area
B1504
When the IG voltage is 9.5 V or more and power switch on (IG) and the following condition is detected:
  1. Multi-information switch (steering pad switch assembly) communication error has been detected more than 3 seconds.
  1. Harness or connector
  2. Spiral cable
  3. Steering pad switch RH
  4. Steering pad switch LH
  5. Combination meter assembly (No. 3 meter circuit plate)

WIRING DIAGRAM


E254381E02


INSPECTION PROCEDURE

HINT:
Before starting the following inspection, confirm the multi-information switch (steering pad switch assembly) setting.

1.READ VALUE USING TECHSTREAM (MULTI DISPLAY SELECT SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Combination Meter / Data List.

  1. Check the values by referring to the table below.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Multi Display Select Switch
    DISP switch in the multi-information switch (steering pad switch assembly)/OFF or ON
    OFF: DISP switch in the multi-information switch (steering pad switch assembly) not pressed
    -
    ON: DISP switch in the multi-information switch (steering pad switch assembly) pressed
    -
    Drive Monitor Reset SW
    TRIP switch in the multi-information switch (steering pad switch assembly)/OFF or ON
    OFF: TRIP switch in the multi-information switch (steering pad switch assembly) not pressed
    -
    ON: TRIP switch in the multi-information switch (steering pad switch assembly) pressed more than 1 second
    -

    OK:
    Steering pad switch assembly (multi-information switch) condition displayed on the Techstream changes with the actual switch operation.



NG
Go to step 2
OK

REPLACE COMBINATION METER ASSEMBLY (NO. 3 METER CIRCUIT PLATE) (Click here)  

2.CHECK SPIRAL CABLE
  1. Check the spiral cable (Click here).



NG
REPLACE SPIRAL CABLE (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (NO. 3 METER CIRCUIT PLATE - STEERING PAD SWITCH RH)
  1. Disconnect the L27 and z9 connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    z9-2 (IG) - Body ground
    Power switch off
    Below 1 V
    z9-2 (IG) - Body ground
    Power switch on (IG)
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z9-7 (DISP) - L27-29 (STRG)
    Always
    Below 1 Ω
    L27-29 (STRG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.REPLACE STEERING PAD SWITCH RH
  1. Replace the steering pad switch RH with a new or a known good one (Click here).

    OK:
    The operation of the combination meter assembly (No. 3 meter circuit plate) returns to normal.



NG
Go to step 5
OK

END 

5.REPLACE STEERING PAD SWITCH LH
  1. Replace the steering pad switch LH with a new or a known good one (Click here).

    OK:
    The operation of the combination meter assembly (No. 3 meter circuit plate) returns to normal.



NG
REPLACE COMBINATION METER ASSEMBLY (NO. 3 METER CIRCUIT PLATE) (Click here)
OK

END