SMART ENTRY AND START SYSTEM > DETAILS |
| FUNCTION OF MAIN COMPONENTS |
The main components for the start function have the following functions:
| Component | Function | |
|
| |
| Electrical Key Transmitter Sub-assembly | Receives the signals from the oscillators and returns the ID code to the door control receiver. | |
| Receives a request signal from the certification ECU (smart key ECU assembly) and forms the actuation area in the vehicle. | |
| Door Control Receiver | Receives the ID code from the electrical key transmitter sub-assembly and transmits it to the certification ECU (smart key ECU assembly). | |
| Power Management Control ECU |
| |
| Certification ECU (Smart Key ECU Assembly) |
| |
| ID Code Box (Immobiliser Code ECU) | Receives the Steering wheel lock unlock/lock or engine immobiliser set/unset request signals from the certification ECU (smart key ECU assembly), certifies them, and transmits each set/unset request signal to the steering lock ECU or power management control ECU. | |
| Stop Light Switch Assembly | Outputs the state of the brake pedal to the power management control ECU. | |
|
| |
| Outputs the shift position "P" detection switch signal to the power management control ECU. | |
| Shift Lever Position Sensor | Outputs the shift position signals to the power management control ECU. | |
| Combination Meter Assembly | Buzzer | Illuminates and sounds to inform the driver of malfunctions in the entry and start system. |
| Multi-information Display | ||
| Master Warning Light | ||
The main components in the entry function have the following functions:
| Component | Function | |
| Electrical Key Transmitter Sub-assembly |
| |
| Main Body ECU (Multiplex Network Body ECU) |
| |
| Certification ECU (Smart Key ECU Assembly) |
| |
| Outside Door Handle (LH, RH) | Door Electrical Key Antenna | Receives a request signal from the certification ECU (smart key ECU assembly) and creates an actuation area around each front door. |
| Lock Sensor |
| |
| Unlock Sensor |
| |
| Electrical Key Antenna | Receives a request signal from the certification ECU (smart key ECU assembly) and forms an actuation area around the back door. | |
| Receives a request signal from the certification ECU (smart key ECU assembly) and forms a actuation area in the vehicle. | |
| Door Control Receiver | Receives the ID code from the electrical key transmitter sub-assembly and transmits it to the certification ECU (smart key ECU assembly). | |
| Back Door Opener Switch Assembly | Back Door Opener Switch | Transmits a back door open request signal to the certification ECU (smart key ECU assembly). |
| Back Door Lock Switch | Transmits a back door lock request signal to the certification ECU (smart key ECU assembly). | |
| Combination Meter Assembly | Buzzer | Illuminates and sounds to inform the driver of malfunctions in the entry and start system. |
| Multi-information Display | ||
| Master Warning Light | ||
| Wireless Door Lock Buzzer | Sounds to inform the driver of malfunctions in the smart entry and start system. | |
| OPERATION |
The special functions of the smart entry and start system only work when the electrical key transmitter sub-assembly is in the actuation area formed by the 6 antennas.
The No. 1 indoor electrical key antenna assembly (front floor), No. 2 indoor electrical key antenna assembly (steering column), and No. 3 indoor electrical key antenna assembly (rear floor) form the interior actuation area.
The door electrical key antenna LH, door electrical key antenna RH, and electrical key antenna (back door) form the exterior actuation area.

| *1 | No. 1 Indoor Electrical Key Antenna Assembly (Front Floor) | *2 | No. 2 Indoor Electrical Key Antenna Assembly (Steering Column) |
| *3 | No. 3 Indoor Electrical Key Antenna Assembly (Rear Floor) | *4 | Door Electrical Key Antenna RH |
| *5 | Door Electrical Key Antenna LH | *6 | Electrical Key Antenna (Back Door) |
| *7 | Electrical Key Transmitter Sub-assembly | - | - |
| *a | Approximately 0.7 to 1.0 m (2.3 to 3.3 ft.) | - | - |
![]() | Interior Actuation Area | ![]() | Exterior Actuation Area |
| Actuation Area | Detail |
| Interior | The interior actuation area of the No. 1, No. 2, No. 3 indoor electrical key antenna assembly (front floor, steering column and rear floor) is formed when the driver door is opened or closed, when the power switch is pushed, when a warning is activated, or when a lock sensor is on. |
| Exterior | The exterior actuation area formed by the door electrical key antennas (LH, RH) and electrical key antenna is approximately 0.7 to 1.0 m (2.3 to 3.3 ft.) from the outside handle of the front doors, or the center of the rear bumper. |
| Around Front Doors | The exterior actuation area of the door electrical key antennas (LH, RH) is formed by transmitting a request signal every 0.25 seconds while the power switch is off and each door is locked. In this way it detects the presence of an electrical key transmitter sub-assembly. When locking the door using the lock sensor on the outer door handle, the actuation area is formed when the lock sensor is touched. |
| Around Back Door |
|
| SYSTEM CONTROL |
Start Function
The start function has different power source patterns to suit the brake pedal and shift state.
| Pattern | Brake Pedal | Shift State | Power Source Pattern |
| A | Depressed | P |
|
| B | Not Depressed | P |
|
| C | Not Depressed | Except P |
|
| D | - | P |
|
| E | - | Except P |
|

Entry Function
The entry function consists of the following functions:
| Function | Outline |
| Wireless Door Lock Control | This function is a convenient system for locking and unlocking all the doors and back door at a distance. The operation of this function is the same as that in the wireless door lock control system. |
| Entry Illumination | When an electrical key transmitter sub-assembly enters the exterior actuation area of the door electrical key antennas (LH and RH), the map light assembly and power switch illumination illuminate. |
| Entry Unlock |
|
| Entry Lock | When an electrical key transmitter sub-assembly is located in the exterior actuation area of any door electrical key antenna (driver, front passenger) or an electrical key antenna (back door) and the power switch is off, all doors can be locked by simply touching the lock sensor. |
| Back Door Open | When an electrical key transmitter sub-assembly is in an exterior actuation area of the electrical key antenna (back door), the back door opens manually by simply pushing the back door open switch. |
| Prevention of Key Confinement | The key confinement prevention function prevents the vehicle from being locked with an electrical key transmitter sub-assembly left inside it. This function operates in 2 different situations: when the lock knob is used (keyless lock) and when an outside door handle lock sensor is used (lock sensor). |
| Warning | The smart entry and start system causes the certification ECU (smart key ECU assembly) to sound the buzzer in the combination meter assembly and wireless door lock buzzer, master warning light, multi information display in order to alert the driver. |
| Battery Saving | If the electrical key transmitter sub-assembly remains within the exterior actuation area of any door electrical key antenna (driver, front passenger) or an electrical key antenna (back door), the system maintains periodic communication with the electrical key transmitter sub-assembly. Therefore, if the vehicle remains parked in that state for a long time, the key battery and the vehicle battery could be drained. |
| Key Cancel |
|
| Key Code Registration | A total of 7 keys (electrical key transmitter sub-assembly) can be registered. Key registration enables the registering (writing and storing) of transmitter recognition codes in the EEPROM that is contained in the certification ECU (smart key ECU assembly). |
The wireless door lock control system allows the following customizable functions:
| Function | Outline |
| All Doors Lock* | Pressing the lock button of the electrical key transmitter sub-assembly locks all doors. |
| All Doors Unlock* | Pressing the unlock button of the electrical key transmitter sub-assembly once unlocks all doors. |
| Answer Back* | When the doors are being locked or unlocked using the electrical key transmitter sub-assembly, the wireless door lock buzzer sounds and the hazard warning lights blink once while locking and twice while unlocking. Also, the answer back function operates when the doors are locked by the automatic relock function. |
| Repeat | If a door is not locked in response to the locking operation of the electrical key transmitter sub-assembly, the main body ECU (multiplex network body ECU) will output a lock signal again after 1 second elapses. |
| Security | Sends a door lock/unlock operation request signal as a rolling code. |
Entry Unlock
While the user carries the electrical key transmitter sub-assembly in the exterior actuation area and the driver door outside handle is held (the back side of the handle is touched), the door unlock sensor built into the handle detects it and the doors are unlocked.
When the doors are unlocked, the hazard warning lights flash twice as an answer back.

| *1 | Door Outside Handle Assembly | *2 | Unlock Sensor |
Entry Lock
When the user gets out of the vehicle while carrying the key and touches the lock sensor of the door outside handle within the exterior actuation area with all the doors closed, the doors are locked.
When the user gets out of the vehicle while carrying the key and presses the back door lock switch on the back door side handle within the back door exterior actuation area with all the doors closed, the doors are locked.
When the doors are locked, the hazard warning lights flash once as an answer back.

| *1 | Door Outside Handle Assembly | *2 | Lock Sensor |

| *1 | Back Door Opener Switch Assembly | *2 | Door Lock Switch |
Back Door Open
The back door is opened when the back door opener switch is pressed within the back door exterior detection area while the user is carrying the electrical key transmitter sub-assembly.

| *1 | Back Door Opener Switch Assembly | *2 | Back Door Opener Switch |
Warning
Depending on the situations listed below, to alert the driver the smart entry and start system either sounds the wireless door lock buzzer, sounds a buzzer in the combination meter assembly, displays a message on the multi-information display and flashes the master warning light, or a combination of the above.
| Situation | Condition |
| A | The hybrid system is left running and the shift lever is in a position other than P when the driver gets out of the vehicle. |
| B | The key reminder sounds. |
| C | The hybrid system is left running and the shift lever is in P when the driver gets out of the vehicle. |
| D | The hybrid system is left running when a passenger gets out of the vehicle while holding the electrical key transmitter sub-assembly. |
| E | The electrical key transmitter sub-assembly is not within the actuation areas. |
| F | The vehicle is driven without an electrical key transmitter sub-assembly. |
| G | The electrical key transmitter sub-assembly is left in the vehicle. |
| H | A door is ajar. |
| I | The key battery is weak. |
| J | Steering lock does not release. |
| K | A malfunction has been detected in a circuit, vehicle speed signal, etc. |
| L | The hybrid system cannot be started (system error) |
| M | The hybrid system cannot be started (driver error) |
| N | An attempt has been made to turn off the vehicle with the shift lever in a position other than P or N. |
| O | Auto power off operation occurs. |
| P | Immobiliser system certification confirmation occurs. |
Situation A
| Possible Effects without Warning | Sudden vehicle movement, Vehicle theft, Vehicle roll-away | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds continuously |
| Multi-information Display | The following warning message is displayed:
| ||
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
| Possible Effects without Warning | Sudden vehicle start-off, Vehicle theft, Vehicle roll-away | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds continuously |
| Multi-information Display | The following warning messages are alternately displayed:
| ||
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | Sounds continuously | ||
| Warning Stop Condition | Combination Meter Assembly | Buzzer |
|
| Wireless Door Lock Buzzer | |||
| Combination Meter Assembly | Multi-information Display ("KEY NOT DETECTED" message displayed) |
| |
| Multi-information Display ("SHIFT TO P POSITION" message displayed) |
| ||
| Master Warning Light | The two warning messages above have been eliminated. | ||
Situation B
| Possible Effects without Warning | Vehicle theft | ||
| Warning Active Condition | Pattern 1 The warning is activated when both of the following conditions are met:
The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds continuously at short and even intervals |
| Multi-information Display | - | ||
| Master Warning Light | - | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
Situation C
| Possible Effects without Warning | Vehicle theft | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed:
| ||
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | Sounds 3 times | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
| Possible Effects without Warning | Vehicle theft | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning messages are alternately displayed:
| ||
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | Sounds for 5 seconds | ||
| Warning Stop Condition | Combination Meter Assembly | Multi-information Display ("TURN POWER OFF" message displayed) |
|
| Multi-information Display ("KEY NOT DETECTED" message displayed) |
| ||
| Master Warning Light | The two warning messages above have been eliminated. | ||
| Wireless Door Lock Buzzer |
| ||
Situation D
| Possible Effect without Warning | Hybrid system cannot be restarted. | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed:
| ||
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | Sounds 3 times | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
Situation E
| Possible Effect without Warning | User becomes confused | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 15 seconds (and then automatically turned off).
| ||
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition |
| ||
Situation F
| Possible Effect without Warning | Hybrid system cannot be restarted. | ||
| Warning Active Condition |
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds nine times |
| Multi-information Display | The following warning message is displayed:
| ||
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
Situation G
| Possible Effect without Warning | Vehicle theft | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sound once |
| Multi-information Display | The following warning message is displayed for 60 seconds (and then automatically turned off).
| ||
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | Sounds for 5 seconds | ||
| Warning Stop Condition | Combination Meter Assembly | Multi-information Display |
|
| Master Warning Light | The warning message above has been eliminated. | ||
| Wireless Door Lock Buzzer |
| ||
Situation H
| Possible Effects without Warning | Vehicle theft | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | - |
| Multi-information Display | - | ||
| Master Warning Light | - | ||
| Wireless Door Lock Buzzer | Sounds for 5 seconds | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
Situation I
| Possible Effect without Warning | Smart entry and start system does not function | ||
| Warning Active Condition | Condition 1: The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 15 seconds (and then automatically turned off).
| ||
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
Situation J
| Possible Effect without Warning | Steering usability function, the hybrid system cannot be started. | ||
| Warning Active Condition | The steering lock cannot be released. | ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 15 seconds (and then automatically turned off).
| ||
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition |
| ||
Situation K
| Possible Effect without Warning | Usability function | ||
| Warning Active Condition | The warning is activated when one of the following conditions is met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 15 seconds (and then automatically turned off).
| ||
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The system returns to normal. | ||
Situation L
| Possible Effect without Warning | Usability function (user cannot start vehicle) | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 30 seconds (and then automatically turned off).
| ||
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
| Possible Effect without Warning | Usability function (user cannot start vehicle) | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed:
| ||
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
Situation M
| Possible Effect without Warning | Usability function (user cannot start vehicle) | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display* | The following warning message is displayed for 10 seconds (and then automatically turned off).
| ||
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The power switch is turned off or on (IG). | ||
| Possible Effect without Warning | Usability function (user cannot start vehicle) | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed:
| ||
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
Situation N
| Possible Effect without Warning | Usability function (user becomes confused) | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed :
| ||
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
| Possible Effect without Warning | Discharged battery, Vehicle roll-away | ||
| Warning Active Condition | After the power switch is turned off with the shift lever in any position other than P, the shift lever is moved to P. | ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed:
| ||
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
Situation O
| Possible Effect without Warning | Vehicle battery discharges | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | - |
| Multi-information Display | The following warning message is displayed for 10 seconds (and then automatically turned off).
| ||
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The power switch is turned to a mode other than off. | ||
Situation P
| Possible Effect without Warning | Malfunction detection | ||
| Warning Active Condition | Key certification result is OK*. | ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 10 seconds (and then automatically turned off).
| ||
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
Battery Saving
Battery saving preserves the vehicle and key batteries. It is activated when the vehicle remains parked for a long time and when the electrical key transmitter sub-assembly is left inside the exterior actuation area.
| Condition | Control | Reinstatement Condition |
| When the vehicle remains parked for a long time. | Control 1:
| When the power switch is turned on (IG), the control is canceled and the system is returned to normal. |
Control 2:
| When the power switch is turned on (IG), the control is canceled and the system is returned to normal.
| |
| When the electrical key transmitter sub-assembly is left within the exterior detection area. |
|
|
In addition to the above functions, the auto power off function helps to reduce drain on the vehicle auxiliary battery by turning the power source mode to off when approximately 60 minutes have elapsed since (a) the shift lever was moved to P with the power source was turned to on (ACC), or (b) the hybrid system is off with the shift lever in P, the power source on (IG) and the vehicle stationary.
Key Cancel
The following system functions can be deactivated by using the key cancel operating procedure.
The system functions can be deactivated by using the following key cancel operating procedure when the power switch is off and the driver door is closed and unlocked.
| Key Cancel operating procedure |
|
Key Code Registration Function
The table below shows the 3 special ID code registration function modes through which up to 7 different codes can be registered. The codes are electronically registered (written to and stored) in the EEPROM. For details, refer to the corresponding Service Bulletin for this model.
| Mode | Function |
| Rewrite | Clears all previously registered codes and registers only the newly received codes. This mode is used whenever a transmitter or the certification ECU (smart key ECU assembly) is replaced. |
| Add | Adds a newly received code while preserving previously registered codes. This mode is used when adding a new transmitter. If the number of codes exceeds 7, the oldest registered code is cleared first. |
| Confirm | Confirms how many codes are currently registered. When adding a new code, this mode is used to check how many codes already exist. |
| CONSTRUCTION |
Electrical Key Transmitter Sub-assembly
The electrical key transmitter sub-assembly consists of a mechanical key, transmitter for the wireless door lock control, transceiver for the entry function, and transponder chip for the engine immobiliser function.
This mechanical key operates the driver door lock cylinder, but cannot be used to start the hybrid system.
The transmitter for the wireless door lock control has a lock button and unlock button.
The transceiver in the electrical key transmitter sub-assembly receives the signals from the oscillators and returns the ID code of the electrical key transmitter sub-assembly to the door control receiver.
The transponder chip for the engine immobiliser function returns a signal to the power switch as a response to the radio wave received from the power switch.

| *1 | Lock Button | *2 | Unlock Button |
| *3 | Mechanical Key | - | - |
Power Switch
The power switch consists of a momentary type switch, illumination, antenna coil, and transponder key amplifier.

Combination Meter Assembly
When the certification ECU (smart key ECU assembly) detects an abnormality with the smart entry and start system, a message appears on a multi-information display. If the hybrid system is stopped in this state, it might not be possible to restart it.

| *a | POWER ON display | *b | Smart Warning display |
| Power Source Condition | Multi-information Display | |
| Brake pedal not depressed | Brake pedal depressed with shift lever in P | |
| Off | OFF | Smart Warning display |
| On (ACC), On (IG) | POWER ON display | Smart Warning display |
| Hybrid System is Operating | OFF | OFF |
Power Management Control ECU
The power management control ECU includes the IG1 relay and IG2 relay actuation circuits, CPU, and hold circuit.
The hold circuit is installed to prevent the power supply to the relays from being cut off when an abnormality occurs in IG1 relay and/or IG2 relay actuation circuits while driving.

| DIAGNOSIS |
Start Function
The power management control ECU and certification ECU (smart key ECU assembly) can detect malfunctions in the smart entry and start system when the power source is on (IG).
When the ECUs detect a malfunction, the multi-information display to warn the driver. At the same time, the ECUs store a 5-digit Diagnostic Trouble Code (DTC) in their memories.
The 5-digit DTCs can be read after connecting the intelligent tester to the DLC3.
The smart entry and start system may not operate successfully if a malfunction occurs.