SMART ENTRY AND START SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS
  1. The main components for the start function have the following functions:

    Component
    Function
    1. Power Switch
      1. Transponder Key Amplifier
    1. Transmits the power switch signal to the certification ECU (smart key ECU assembly).
    2. Receives the ID code and transmits it to the certification ECU (smart key ECU assembly) when the key battery is too weak to respond to the tuner based on the signals from the indoor electrical key antennas.
    Electrical Key Transmitter Sub-assembly
    Receives the signals from the indoor electrical key antennas and returns the ID code to the door control receiver.
    1. No. 1 Indoor Electrical Key Antenna Assembly (Front Floor)
    2. No. 2 Indoor Electrical Key Antenna Assembly (Steering Column)
    3. No. 3 Indoor Electrical Key Antenna Assembly (Rear Floor)
    Receives a request signal from the certification ECU (smart key ECU assembly) and forms the actuation area in the vehicle.
    Door Control Receiver
    Receives the ID code from the electrical key transmitter sub-assembly and transmits it to the certification ECU (smart key ECU assembly).
    Hybrid Vehicle Control ECU
    Receives the signal from the ID code box (immobiliser code ECU) and controls the hybrid system.
    Certification ECU (Smart Key ECU Assembly)
    1. Certifies the ID code received from the door control receiver and transmits the certification results to the ID code box (immobiliser code ECU) and steering lock ECU.
    2. Transmits the steering wheel lock/unlock request signals.
    3. Transmits the engine immobiliser set/unset request signals.
    4. Switches the power source ("power switch") among 4 modes (off, on (ACC), on (IG), READY) in accordance with the shift state and the brake pedal signal.
    5. Controls the smart entry and start system in accordance with the signals received from the switches and each ECU.
    ID Code Box (Immobiliser Code ECU)
    Receives the Steering wheel lock unlock/lock or engine immobiliser set/unset request signals from the certification ECU (smart key ECU assembly), certifies them, and transmits each set/unset request signal to the steering lock ECU or hybrid vehicle control ECU.
    Stop Light Switch Assembly
    Outputs the state of the brake pedal to the certification ECU (smart key ECU assembly).
    1. Steering Lock Actuator Assembly
      1. Steering Lock ECU
    1. Receives the command signal from the certification ECU (smart key ECU assembly) and activates the steering lock actuator.
    2. Registers the ID verification code.
    1. Lower Shift Lever Assembly
      1. Shift Lock Control ECU
    Outputs the shift position "P" detection switch signal to the certification ECU (smart key ECU assembly).
    Shift Lever Position Sensor
    Outputs the shift position signals to the hybrid vehicle control ECU.
    Combination Meter Assembly
    Buzzer
    Illuminates and sounds to inform the driver of malfunctions in the entry and start system.
    Multi-information Display
    Master Warning Light

  2. The main components in the entry function have the following functions:

    Component
    Function
    Electrical Key Transmitter Sub-assembly
    1. Outputs information such as the key ID and vehicle ID when request signals that are output by the electrical key antennas are received.
    2. Outputs a request signal when the lock or unlock button on the electrical key transmitter sub-assembly is pushed.
    3. Has an integrated mechanical key that can be used to unlock the doors when the key battery is weak.
    Main Body ECU (Multiplex Network Body ECU)
    1. Receives a request signal from the certification ECU (smart key ECU assembly) and actuates the door lock motors to unlock or lock all the doors and back door.
    2. Transmits the condition of each door and the back door to the certification ECU (smart key ECU assembly).
    Certification ECU (Smart Key ECU Assembly)
    1. Certifies the ID code received from the door control receiver and transmits the certification results to the main body ECU (multiplex network body ECU).
    2. Controls the antennas, lock sensor and unlock sensor.
    3. Transmits the door lock/unlock request signals during the entry function.
    Outside Door Handle (LH, RH)
    Door Electrical Key Antenna
    Receives a request signal from the certification ECU (smart key ECU assembly) and creates an actuation area around each front door.
    Lock Sensor
    1. Detects when a person touches the outer door handle.
    2. Transmits door lock request signals to the certification ECU (smart key ECU assembly).
    Unlock Sensor
    1. Detects when a person touches the inside of an outer door handle.
    2. Transmits door unlock request signals to the certification ECU (smart key ECU assembly).
    Electrical Key Antenna
    Receives a request signal from the certification ECU (smart key ECU assembly) and forms an actuation area around the back door.
    1. No. 1 Indoor Electrical Key Antenna Assembly (Front Floor)
    2. No. 2 Indoor Electrical Key Antenna Assembly (Steering Column)
    3. No. 3 Indoor Electrical Key Antenna Assembly (Rear Floor)
    Receives a request signal from the certification ECU (smart key ECU assembly) and forms an actuation area in the vehicle.
    Door Control Receiver
    Receives the ID code from the electrical key transmitter sub-assembly and transmits it to the certification ECU (smart key ECU assembly).
    Back Door Opener Switch Assembly
    Back Door Opener Switch
    Transmits a back door open request signal to the certification ECU (smart key ECU assembly).
    Back Door Lock Switch
    Transmits a back door lock request signal to the certification ECU (smart key ECU assembly).
    Combination Meter Assembly
    Buzzer
    Illuminates and sounds to inform the driver of malfunctions in the entry and start system.
    Multi-information Display
    Master Warning Light
    Wireless Door Lock Buzzer
    Sounds to inform the driver of malfunctions in the smart entry and start system.


OPERATION
  1. The special functions of the smart entry and start system only work when the electrical key transmitter sub-assembly is in the actuation area formed by the 6 antennas.

  2. The No. 1 indoor electrical key antenna assembly (front floor), No. 2 indoor electrical key antenna assembly (steering column), and No. 3 indoor electrical key antenna assembly (rear floor) form the interior actuation area.



  3. The door electrical key antenna LH, door electrical key antenna RH, and electrical key antenna (back door) form the exterior actuation area.


    Y118173E01


    Text in Illustration 
    *1
    No. 1 Indoor Electrical Key Antenna Assembly (Front Floor)
    *2
    No. 2 Indoor Electrical Key Antenna Assembly (Steering Column)
    *3
    No. 3 Indoor Electrical Key Antenna Assembly (Rear Floor)
    *4
    Door Electrical Key Antenna RH
    *5
    Door Electrical Key Antenna LH
    *6
    Electrical Key Antenna (Back Door)
    *7
    Electrical Key Transmitter Sub-assembly
    -
    -
    *a
    Approximately 0.7 to 1.0 m (2.3 to 3.3 ft.)
    -
    -
    V100144
    Interior Actuation Area
    V100145
    Exterior Actuation Area

    Each Actuation Area 
    Actuation Area
    Detail
    Interior
    The interior actuation area of the No. 1, No. 2, No. 3 indoor electrical key antenna assemblies (front floor, steering column and rear floor) is formed when the driver door is opened or closed, when the power switch is pushed, when a warning is activated, or when a lock sensor is on.
    Exterior
    The exterior actuation area formed by the door electrical key antennas (LH, RH) and electrical key antenna is approximately 0.7 to 1.0 m (2.3 to 3.3 ft.) from the outside handle of the front doors, or the center of the rear bumper.
    Around Front Doors
    The exterior actuation area of the door electrical key antennas (LH, RH) is formed by transmitting a request signal every 0.25 seconds while the power switch is off and each door is locked. In this way it detects the presence of an electrical key transmitter sub-assembly. When locking the door using the lock sensor on the outer door handle, the actuation area is formed when the lock sensor is touched.
    Around Back Door
    1. The exterior actuation area of the electrical key antenna (back door) is formed when the back door opener switch is on.
    2. The exterior actuation area of the electrical key antenna (back door) is formed when the door lock switch (back door) is on.


SYSTEM CONTROL


  1. Start Function



    1. The start function has different power source patterns to suit the brake pedal and shift state.

      Pattern
      Brake Pedal
      Shift State
      Power Source Pattern
      A
      Depressed
      P
      1. When the power switch is pushed once.
        1. Off → READY (The hybrid system is started)
      B
      Not Depressed
      P
      1. Each time the power switch is pushed.
        1. Off → On (ACC) → On (IG) → Off
      C
      Not Depressed
      Except P
      1. Each time the power switch is pushed.
        1. Off → On (ACC) → On (IG) →On (ACC)
      D
      -
      P
      1. When the power switch is pushed in the on (IG) or READY condition.
        1. On (IG) or READY → Off
      E
      -
      Except P
      1. When the power switch is pushed in the on (IG) or READY condition.
        1. On (IG) or READY → On (ACC)


      Y118366E03

      NOTICE:
      1. Normally, the operation of the power switch is disabled while the vehicle is being driven. However, in an emergency, by pushing the power switch for approximately 2 seconds or more or push the power switch 3 times or more in a row, the driver can stop the hybrid system while the vehicle is in motion.
      2. If no signals are transmitted to the certification ECU (smart key ECU assembly) due to malfunctions in the stop light switch assembly, the hybrid system may not start when the power switch is pushed. In such cases, performing the following procedure may enable the hybrid system to start: 1) operate parking brake and when the shift lever is in position P, 2) push the power switch to turn the power source from off to on (ACC), and 3) push the power switch again and hold it for 15 seconds or more.
      3. The above 2 operations must be applied only in emergency situations. Under normal conditions, the hybrid system must not be stopped by pushing the power switch while driving. Also, it should not be started without depressing the brake pedal or when a shift state other than park (P) has been selected.

  2. Entry Function

    1. The entry function consists of the following functions:

      Function
      Outline
      Wireless Door Lock Control
      This function is a convenient system for locking and unlocking all the doors and back door at a distance. The operation of this function is the same as that in the wireless door lock control system.
      Entry Illumination
      When an electrical key transmitter sub-assembly enters the exterior actuation area of the door electrical key antennas (LH and RH), the map light assembly, the No. 1 room light assembly*, and the power switch illumination illuminate.
      Entry Unlock
      1. When an electrical key transmitter sub-assembly is located in the exterior actuation area of any door electrical key antenna, the door will unlock after the inner part of either front outside door handle is touched.
        1. The driver outside door handle unlocks the driver door.
        2. The front passenger outside door handle unlocks all doors and the back door.
      Entry Lock
      When an electrical key transmitter sub-assembly is located in the exterior actuation area of any door electrical key antenna (driver, front passenger) or an electrical key antenna (back door) and the power switch is off, all doors can be locked by touching the lock sensor of the driver or front passenger outside door handle assembly or by pressing the lock switch of the back door opener switch.
      Back Door Open
      When an electrical key transmitter sub-assembly is in an exterior actuation area of the electrical key antenna (back door), the back door opens manually by simply pushing the back door open switch.
      Prevention of Key Confinement
      The key confinement prevention function prevents the vehicle from being locked with an electrical key transmitter sub-assembly left inside it. This function operates in 2 different situations: when the lock knob is used (keyless lock) and when an outside door handle lock sensor is used (lock sensor).
      Warning
      The smart entry and start system causes the certification ECU (smart key ECU assembly) to sound the buzzer in the combination meter assembly and wireless door lock buzzer, master warning light, multi information display in order to alert the driver.
      Battery Saving
      If the electrical key transmitter sub-assembly remains within the exterior actuation area of any door electrical key antenna (driver, front passenger) or an electrical key antenna (back door), the system maintains periodic communication with the electrical key transmitter sub-assembly. Therefore, if the vehicle remains parked in that state for a long time, the key battery and the vehicle battery could be drained.
      Key Cancel
      1. The following key functions can be cancelled by following certain procedures.
        1. Entry unlock/lock
        2. Back door open
        3. Prevention of key confinement
        4. Warning
        5. Entry Illumination
      Key Code Registration
      A total of 7 keys (electrical key transmitter sub-assembly) can be registered. Key registration enables the registering (writing and storing) of transmitter recognition codes in the EEPROM that is contained in the certification ECU (smart key ECU assembly).

      1. *: Models with No. 1 room light assembly

    2. The wireless door lock control system allows the following customizable functions:

      Function
      Outline
      All Doors Lock*
      Pressing the lock button of the electrical key transmitter sub-assembly locks all doors.
      All Doors Unlock*
      Pressing the unlock button of the electrical key transmitter sub-assembly once unlocks all doors.
      Answer Back*
      When the doors are being locked or unlocked using the electrical key transmitter sub-assembly, the wireless door lock buzzer sounds and the hazard warning lights blink once while locking and twice while unlocking. Also, the answer back function operates when the doors are locked by the automatic relock function.
      Repeat
      If a door is not locked in response to the locking operation of the electrical key transmitter sub-assembly, the main body ECU (multiplex network body ECU) will output a lock signal again after 1 second elapses.
      Security
      Sends a door lock/unlock operation request signal as a rolling code.

      1. *: The customize settings can be turned on/off using the customized body electronics system. For details, refer to the Repair Manual.



  3. Entry Unlock

    1. While the user carries the electrical key transmitter sub-assembly in the exterior actuation area and the driver door outside handle is held (the back side of the handle is touched), the door unlock sensor built into the handle detects it and the doors are unlocked.



    2. When the doors are unlocked, the hazard warning lights flash twice as an answer back.


      Y111281E01


      Text in Illustration 
      *1
      Door Outside Handle Assembly
      *2
      Unlock Sensor



  4. Entry Lock

    1. When the user gets out of the vehicle while carrying the key and touches the lock sensor of the door outside handle within the exterior actuation area with all the doors closed, the doors are locked.

    2. When the user gets out of the vehicle while carrying the key and presses the back door lock switch on the back door side handle within the back door exterior actuation area with all the doors closed, the doors are locked.



    3. When the doors are locked, the hazard warning lights flash once as an answer back.


      Y118384E01


      Text in Illustration 
      *1
      Door Outside Handle Assembly
      *2
      Lock Sensor

      Y118175E01


      Text in Illustration 
      *1
      Back Door Opener Switch Assembly
      *2
      Door Lock Switch



  5. Back Door Open



    1. The back door is opened when the back door opener switch is pressed within the back door exterior detection area while the user is carrying the electrical key transmitter sub-assembly.


      Y118174E01


      Text in Illustration 
      *1
      Back Door Opener Switch Assembly
      *2
      Back Door Opener Switch

  6. Warning

    1. Depending on the situations listed below, to alert the driver the smart entry and start system either sounds the wireless door lock buzzer, sounds a buzzer in the combination meter assembly, displays a message on the multi-information display and flashes the master warning light, or a combination of the above.

      Situation
      Condition
      A
      The hybrid system is left running and the shift lever is in a position other than P when the driver gets out of the vehicle.
      B
      The key reminder sounds.
      C
      The hybrid system is left running and the shift lever is in P when the driver gets out of the vehicle.
      D
      The hybrid system is left running when a passenger gets out of the vehicle while holding the electrical key transmitter sub-assembly.
      E
      The electrical key transmitter sub-assembly is not within the actuation areas.
      F
      The vehicle is driven without an electrical key transmitter sub-assembly.
      G
      The electrical key transmitter sub-assembly is left in the vehicle.
      H
      A door is ajar.
      I
      The key battery is weak.
      J
      Steering lock does not release.
      K
      A malfunction has been detected in a circuit, vehicle speed signal, etc.
      L
      The hybrid system cannot be started (system error)
      M
      The hybrid system cannot be started (driver error)
      N
      An attempt has been made to turn off the vehicle with the shift lever in a position other than P or N.
      O
      Auto power off operation occurs.
      P
      Immobiliser system certification confirmation occurs.

    2. Situation A

      1. There are 2 patterns for situation A.
        1. Pattern 1:
          When the shift lever is in a position other than P, the power switch is in a mode other than off, the driver opens the door and attempts to get out of the vehicle.
          In this situation, the following control is performed:

          Possible Effects without Warning
          Sudden vehicle movement, Vehicle theft, Vehicle roll-away
          Warning Active Condition
          The warning is activated when all of the following conditions are met:
          1. The power switch is in a mode other than off.
          2. The shift lever is in any position except P.
          3. The vehicle speed is 0 km/h (0 mph).
          4. The driver door is opened.
          Warning Method
          Combination Meter Assembly
          Buzzer
          Sounds continuously
          Multi-information Display
          The following warning message is displayed:
          1. SHIFT TO P POSITION
          Master Warning Light
          Blinks
          Wireless Door Lock Buzzer
          -
          Warning Stop Condition
          The warning is stopped when one of the following conditions is met:
          1. The power switch is turned off.
          2. The shift lever is moved to P.
          3. The vehicle speed is above 5 km/h (3 mph).
          4. The driver door is closed.
        2. Pattern 2:
          Under the situation of pattern 1, the driver closes the door and attempts to leave the vehicle while holding the electrical key transmitter sub-assembly.
          In this situation, the following control is performed:

          Possible Effects without Warning
          Sudden vehicle start-off, Vehicle theft, Vehicle roll-away
          Warning Active Condition
          The warning is activated when all of the following conditions are met:
          1. The shift lever is in any position except P.
          2. The power switch is in a mode other than off.
          3. The vehicle speed is 0 km/h (0 mph).
          4. The electrical key transmitter sub-assembly is not detected in the vehicle.
          5. The driver door is opened → closed.
          Warning Method
          Combination Meter Assembly
          Buzzer
          Sounds continuously
          Multi-information Display
          The following warning messages are alternately displayed:
          1. SHIFT TO P POSITION
          2. KEY NOT DETECTED
          Master Warning Light
          Blinks
          Wireless Door Lock Buzzer
          Sounds continuously
          Warning Stop Condition
          Combination Meter Assembly
          Buzzer
          1. The power switch is turned off.
          2. The shift lever is moved to P.
          3. The vehicle speed is above 5 km/h (3 mph).
          4. The electrical key transmitter sub-assembly is detected in the vehicle.
          Wireless Door Lock Buzzer
          Combination Meter Assembly
          Multi-information Display ("KEY NOT DETECTED" message displayed)
          1. The power switch is turned off.
          2. The electrical key transmitter sub-assembly is detected in the vehicle.
          Multi-information Display ("SHIFT TO P POSITION" message displayed)
          1. The shift lever is moved to P.
          2. The vehicle speed is above 5 km/h (3 mph).
          Master Warning Light
          The two warning messages above have been eliminated.

    3. Situation B

      1. There are 2 patterns for situation B.
        1. Pattern 1:
          The power switch is on (ACC), the driver door is opened and the driver attempts to leave the vehicle.
        2. Pattern 2:
          When the driver door is open, the power switch is turned from on (IG) to off, the steering remains unlocked and the driver attempts to leave the vehicle.
          In these situations, the following control is performed:

      Possible Effects without Warning
      Vehicle theft
      Warning Active Condition
      Pattern 1
      The warning is activated when all of the following conditions are met:
      1. The shift lever is in P.
      2. The power switch is on (ACC).
      3. The driver door is open.
      Pattern 2
      The warning is activated when all of the following conditions are met:
      1. The shift lever is in P.
      2. The power switch is turned from on (IG) to off.
      3. The driver door is open.
      4. The steering lock remains unlocked.
      Warning Method
      Combination Meter Assembly
      Buzzer
      Sounds continuously at short and even intervals
      Multi-information Display
      -
      Master Warning Light
      -
      Wireless Door Lock Buzzer
      -
      Warning Stop Condition
      The warning is stopped when one of the following conditions is met:
      1. The power switch is turned on (IG).
      2. The driver door is closed.
      3. The power switch is turned off and the steering wheel lock control is performed.

    4. Situation C

      1. There are 2 patterns for situation C.
        1. Pattern 1:
          When the shift lever is in P and the power switch is in a mode other than off, the driver closes the driver door and attempts to leave the vehicle while holding the electrical key transmitter sub-assembly.
          In this situation, the following control is performed:

          Possible Effects without Warning
          Vehicle theft
          Warning Active Condition
          The warning is activated when all of the following conditions are met:
          1. The shift lever is in P.
          2. The power switch is in a mode other than off.
          3. The electrical key transmitter sub-assembly is not detected in the vehicle.
          4. The driver door is opened → closed.
          5. The vehicle speed is 0 km/h (0 mph).
          Warning Method
          Combination Meter Assembly
          Buzzer
          Sounds once
          Multi-information Display
          The following warning message is displayed:
          1. KEY NOT DETECTED
          Master Warning Light
          Blinks
          Wireless Door Lock Buzzer
          Sounds 3 times
          Warning Stop Condition
          The warning is stopped when either of the following conditions is met:
          1. The power switch is turned off.
          2. The electrical key transmitter sub-assembly is detected in the vehicle.
        2. Pattern 2:
          Under the situation of pattern 1, the driver touches the lock sensor on the door outside handle.
          In this situation, the following control is performed:

          Possible Effects without Warning
          Vehicle theft
          Warning Active Condition
          The warning is activated when all of the following conditions are met:
          1. The power switch is in a mode other than off.
          2. The shift lever is in P.
          3. The lock sensor on the outer door handle is on (touched).
          4. The vehicle speed is 0 km/h (0 mph).
          5. The electrical key transmitter sub-assembly is not detected in the vehicle.
          6. The electrical key transmitter sub-assembly is detected in an outside detection area.
          Warning Method
          Combination Meter Assembly
          Buzzer
          Sounds once
          Multi-information Display
          The following warning messages are alternately displayed:
          1. TURN POWER OFF
          2. KEY NOT DETECTED
          Master Warning Light
          Blinks
          Wireless Door Lock Buzzer
          Sounds for 5 seconds
          Warning Stop Condition
          Combination Meter Assembly
          Multi-information Display ("TURN POWER OFF" message displayed)
          1. 60 seconds elapse.
          2. The power switch is turned off.
          3. The shift lever is moved to any position except P.
          4. The vehicle speed is above 5 km/h (3 mph).
          Multi-information Display ("KEY NOT DETECTED" message displayed)
          1. The power switch is turned off.
          2. The electrical key transmitter sub-assembly is detected in the vehicle.
          Master Warning Light
          The two warning messages above have been eliminated.
          Wireless Door Lock Buzzer
          1. Any door is opened or closed.
          2. The power switch is turned off.
          3. The shift lever is moved to any position except P.
          4. The vehicle speed is above 5 km/h (3 mph).
          5. The electrical key transmitter sub-assembly is detected in the vehicle.

    5. Situation D

      1. When the hybrid system is operating, a passenger leaves the vehicle while holding the electrical key transmitter sub-assembly.
        In this situation, the following control is performed:

        Possible Effect without Warning
        Hybrid system cannot be restarted.
        Warning Active Condition
        The warning is activated when all of the following conditions are met:
        1. The power switch is in a mode other than off.
        2. A door other than the driver door is opened → closed.
        3. The vehicle speed is 0 km/h (0 mph).
        4. The electrical key transmitter sub-assembly is not detected in the vehicle.
        Warning Method
        Combination Meter Assembly
        Buzzer
        Sounds once
        Multi-information Display
        The following warning message is displayed:
        1. KEY NOT DETECTED
        Master Warning Light
        Blinks
        Wireless Door Lock Buzzer
        Sounds 3 times
        Warning Stop Condition
        The warning is stopped when either of the following conditions is met:
        1. The power switch is turned off.
        2. The electrical key transmitter sub-assembly is detected again or returned to the vehicle.

    6. Situation E

      1. When the electrical key transmitter sub-assembly is not in the vehicle or the key battery is dead, the driver attempts to start the hybrid system or turn the power switch on (IG).
        In this situation, the following control is performed:

        Possible Effect without Warning
        User becomes confused
        Warning Active Condition
        The warning is activated when all of the following conditions are met:
        1. A door has not been unlocked using the mechanical key.
        2. The power switch is pressed.
        3. The electrical key transmitter sub-assembly is not in the vehicle or the key battery is very low.
        4. The immobiliser system is set.
        Warning Method
        Combination Meter Assembly
        Buzzer
        Sounds once
        Multi-information Display
        The following warning message is displayed for 15 seconds (and then automatically turned off).
        1. KEY NOT DETECTED
        Master Warning Light
        Blinks
        Wireless Door Lock Buzzer
        -
        Warning Stop Condition
        1. The electrical key transmitter sub-assembly is detected again or returned to the vehicle.
        2. Smart warning light illuminates for 15 seconds.

    7. Situation F

      1. A warning message appears on the multi-information display when the vehicle starts moving without a registered electrical key transmitter sub-assembly in the vehicle.
        In this situation, the following control is performed:

        Possible Effect without Warning
        Hybrid system cannot be restarted.
        Warning Active Condition
        1. When vehicle speed is detected for the first time after the electrical key transmitter sub-assembly is removed from the vehicle, the warning is activated.
        2. The vehicle speed is above 5 km/h (3 mph).
        Warning Method
        Combination Meter Assembly
        Buzzer
        Sounds nine times
        Multi-information Display
        The following warning message is displayed:
        1. KEY NOT DETECTED
        Master Warning Light
        Blinks
        Wireless Door Lock Buzzer
        -
        Warning Stop Condition
        The warning is stopped when either of the following conditions is met:
        1. The power switch is turned off.
        2. The electrical key transmitter sub-assembly is detected in the vehicle.

    8. Situation G

      1. The lock sensor on a door outside handle is touched to perform entry lock with the electrical key transmitter sub-assembly left in the vehicle.
      2. In this situation, the following control is performed:

        Possible Effect without Warning
        Vehicle theft
        Warning Active Condition
        The warning is activated when all of the following conditions are met:
        1. The power switch is off.
        2. All doors are closed.
        3. The electrical key transmitter sub-assembly is detected in the vehicle.
        4. Any door is unlocked.
        5. The lock sensor on the outer door handle is on (touched).
        6. The vehicle speed is 0 km/h (0 mph).
        Warning Method
        Combination Meter Assembly
        Buzzer
        -
        Multi-information Display
        The following warning message is displayed for 60 seconds (and then automatically turned off).
        1. KEY DETECTED IN VEHICLE
        Master Warning Light
        Blinks
        Wireless Door Lock Buzzer
        Sounds for 5 seconds
        Warning Stop Condition
        Combination Meter Assembly
        Multi-information Display
        1. 60 seconds elapse.
        2. The power switch is turned to a mode other than off.
        3. The vehicle speed is above 5 km/h (3 mph).
        4. Lock operation is detected.
        Master Warning Light
        The warning message above has been eliminated.
        Wireless Door Lock Buzzer
        1. Any door is opened.
        2. The power switch is turned to a mode other than off.
        3. The vehicle speed is above 5 km/h (3 mph).
        4. Lock operation is detected.

    9. Situation H

      1. The lock sensor on the door outside handle is touched to perform entry lock, however, a door is open.
        In this situation, the following control is performed:

        Possible Effects without Warning
        Vehicle theft
        Warning Active Condition
        The warning is activated when all of the following conditions are met:
        1. The power switch is off.
        2. Any door is open other than the door where the entry lock operation is performed.
        3. The lock sensor on the outer door handle is on (touched), the lock switch on the electrical key transmitter subassembly is pressed.
        4. The electrical key transmitter sub-assembly is in an outside detection area.
        Warning Method
        Combination Meter Assembly
        Buzzer
        -
        Multi-information Display
        -
        Master Warning Light
        -
        Wireless Door Lock Buzzer
        Sounds for 5 seconds
        Warning Stop Condition
        The warning is stopped when one of the following conditions is met:
        1. The power switch is turned to a mode other than off.
        2. All doors are closed.
        3. An unlock operation is performed using the wireless door lock remote function.
        4. The unlock sensor on the inside of an outer door handle is used to perform entry unlock.

    10. Situation I

      1. The vehicle is driven using an electrical key transmitter sub-assembly that has a low battery.
        In this situation, the following control is performed:

        Possible Effect without Warning
        Usability function, the hybrid system cannot be restarted
        Warning Active Condition
        Condition 1: The warning is activated when all of the following conditions are met:
        1. The power switch is turned off after being left on (IG) for more than 20 minutes.
        2. The key battery voltage is low.
        3. The electrical key transmitter sub-assembly is in the vehicle.
        4. The vehicle speed is 0 km/h (0 mph).
        Condition 2: The warning is activated when all of the following conditions are met:
        1. Condition 1 described above is met (past).
        2. The hybrid system has been started.
        3. The key battery voltage is low.
        4. The electrical key transmitter sub-assembly is in the vehicle.
        5. The vehicle speed is 0 km/h (0 mph).
        Warning Method
        Combination Meter Assembly
        Buzzer
        Sounds once
        Multi-information Display
        The following warning message is displayed for 15 seconds (and then automatically turned off).
        1. KEY BATTERY LOW
        Master Warning Light
        Blinks
        Wireless Door Lock Buzzer
        -
        Warning Stop Condition
        The warning is stopped when either of the following conditions is met:
        1. The key battery is replaced with a new one.
        2. The vehicle speed is above 5 km/h (3 mph).

    11. Situation J

      1. The steering lock cannot be released.
        In this situation, the following control is performed:

        Possible Effect without Warning
        Usability function
        Warning Active Condition
        The steering lock cannot be released.
        Warning Method
        Combination Meter Assembly
        Buzzer
        Sounds once
        Multi-information Display
        The following warning message is displayed for 15 seconds (and then automatically turned off).
        1. STEERING LOCK ACTIVE
        Master Warning Light
        Blinks
        Wireless Door Lock Buzzer
        -
        Warning Stop Condition
        1. The warning is stopped when one of the following conditions is met :
        2. The power switch is pushed while the steering wheel is turned left and right, and the steering lock successfully disengages.

    12. Situation K

      1. An IC circuit malfunction, vehicle speed signal malfunction or malfunction that interferes with steering lock ECU (steering lock actuator assembly) operation, has been detected.
        In this situation, the following control is performed:

        Possible Effect without Warning
        Malfunction detection
        Warning Active Condition
        The warning is activated when one of the following conditions is met:
        1. The steering lock ECU (steering lock actuator assembly), driver of the certification ECU (smart key ECU assembly) or lock/unlock position switch is malfunctioning.
        2. An IG relay output circuit malfunction occurs three times or more consecutively.
        3. The vehicle speed is judged as abnormal or vehicle speed signal communication is malfunctioning.
        Warning Method
        Combination Meter Assembly
        Buzzer
        Sounds once
        Multi-information Display
        The following warning message is displayed for 15 seconds (and then automatically turned off).
        1. CHECK ENTRY AND START SYSTEM
        Master Warning Light
        Blinks
        Wireless Door Lock Buzzer
        -
        Warning Stop Condition
        The system returns to normal.

    13. Situation L

      1. There are 2 patterns for situation L.
        1. Pattern 1:
          When the power switch is pushed, the electrical key transmitter sub-assembly cannot be detected in the vehicle 2 times in a row.
          In this situation, the following control is performed:

          Possible Effect without Warning
          Usability function (user cannot start vehicle)
          Warning Active Condition
          The warning is activated when all of the following conditions are met:
          1. The immobiliser system is set.
          2. The electrical key transmitter sub-assembly is not detected in the vehicle.
          3. When the power switch is pressed, a certification error occurs 2 times in a row.
          Warning Method
          Combination Meter Assembly
          Buzzer
          Sounds once
          Multi-information Display
          The following warning message is displayed for 30 seconds (and then automatically turned off).
          1. DEPRESS BRAKE PEDAL, TOUCH POWER SWITCH WITH KEY
          Master Warning Light
          Blinks
          Wireless Door Lock Buzzer
          -
          Warning Stop Condition
          The warning is stopped when one of the following conditions is met:
          1. The immobiliser system certification result is OK.
          2. The electrical key transmitter sub-assembly is detected in the vehicle.
          3. Key certification in the vehicle has stopped either because 30 seconds have passed since any of the doors was opened and closed, or because the brake pedal is depressed.
      2. Pattern 2:
        The driver attempts to start the hybrid system after unlocking the driver door using the mechanical key.
        In this situation, the following control is performed:

        Possible Effect without Warning
        Usability function (user cannot start vehicle)
        Warning Active Condition
        The warning is activated when all of the following conditions are met:
        1. The driver door is unlocked using the mechanical key.
        2. The immobiliser system is set.
        3. The power switch is pushed.
        4. The electrical key transmitter sub-assembly is not detected in the vehicle.
        Warning Method
        Combination Meter Assembly
        Buzzer
        Sounds once
        Multi-information Display
        The following warning message is displayed:
        1. DEPRESS BRAKE PEDAL, TOUCH POWER SWITCH WITH KEY
        Master Warning Light
        Blinks
        Wireless Door Lock Buzzer
        -
        Warning Stop Condition
        The warning is stopped when either of the following conditions is met:
        1. The immobiliser system certification result is OK.
        2. The electrical key transmitter sub-assembly is detected in the vehicle.

    14. Situation M

      1. There are 2 patterns for situation M.
        1. Pattern 1:
          A warning message appears on the multi-information display when the driver does not follow the proper procedure to start the vehicle.
          In this situation, the following control is performed:

          Possible Effect without Warning
          Usability function (user cannot start vehicle)
          Warning Active Condition
          The warning is activated when all of the following conditions are met:
          1. The power switch is off.*
          2. Driver door is closed → opened.*
          3. The power switch is turned from off to on (ACC) more than twice with the hybrid system off and the brake pedal not depressed.
          Warning Method
          Combination Meter Assembly
          Buzzer
          Sounds once
          Multi-information Display*
          The following warning message is displayed for 10 seconds (and then automatically turned off).
          1. DEPRESS BRAKE PEDAL AND PUSH POWER SWITCH TO START
          Master Warning Light
          Blinks
          Wireless Door Lock Buzzer
          -
          Warning Stop Condition
          The power switch is turned off or on (IG).
          *: Precondition
      2. Pattern 2:
        A message indicating how to start the hybrid system appears on the multi-information display when the shift lever is in a position in which the hybrid system cannot be started.
        In this situation, the following control is performed:

        Possible Effect without Warning
        Usability function (user cannot start vehicle)
        Warning Active Condition
        The warning is activated when all of the following conditions are met:
        1. The hybrid system is stopped.
        2. The shift lever is not in P.
        3. The vehicle speed is 0 km/h (0 mph).
        4. More than 0.5 seconds have elapsed since the power switch was turned on (IG).
        5. The starter is not operating.
        Warning Method
        Combination Meter Assembly
        Buzzer
        Sounds once
        Multi-information Display
        The following warning message is displayed:
        1. SHIFT TO P POSITION TO START
        Master Warning Light
        Blinks
        Wireless Door Lock Buzzer
        -
        Warning Stop Condition
        The warning is stopped when one of the following conditions is met:
        1. The shift lever is moved to P.
        2. The vehicle speed is above 0 km/h (0 mph).
        3. The power switch is turned off or on (ACC).
        4. The hybrid system is started.

    15. Situation N

      1. There are 2 patterns for situation N.
        1. Pattern 1:
          A warning message appears on the multi-information display when the driver attempts to turn the power switch off with the shift lever in a position other than P.
          In this situation, the following control is performed:

          Possible Effect without Warning
          Discharged battery, Vehicle roll-away
          Warning Active Condition
          The warning is activated when all of the following conditions are met:
          1. The shift lever is in any position other than P.
          2. The power switch is turned from on (IG) to on (ACC)*.
          3. Even though the power switch is pressed, the power source mode does not change to off (excluding emergency stop operation).
          Warning Method
          Combination Meter Assembly
          Buzzer
          Sounds once
          Multi-information Display
          The following warning message is displayed :
          1. SHIFT TO P POSITION
          Master Warning Light
          Blinks
          Wireless Door Lock Buzzer
          -
          Warning Stop Condition
          The warning is stopped when either of the following conditions is met:
          1. The shift lever is moved to P.
          2. The power switch is in a mode other than on (ACC).
          *: The driver has attempted to turn the power switch off, but the system has selected on (ACC) due to the shift lever position. Situation A may follow this if the driver does not correct the problem.
      2. Pattern 2:
        Under the situation of pattern 1, the shift lever is moved to P.
        In this situation, the following control is performed:

        Possible Effect without Warning
        Discharged battery, Vehicle roll-away
        Warning Active Condition
        After the power switch is turned off with the shift lever in any position other than P, the shift lever is moved to P.
        Warning Method
        Combination Meter Assembly
        Buzzer
        Sounds once
        Multi-information Display
        The following warning message is displayed:
        1. TURN POWER OFF
        Master Warning Light
        Blinks
        Wireless Door Lock Buzzer
        -
        Warning Stop Condition
        The warning is stopped when either of the following conditions is met:
        1. The shift lever is moved to a position other than P.
        2. The power switch is turned to a mode other than on (ACC).

    16. Situation O

      1. A warning message appears on the multi-information display when automatic power off operation occurs.
        In this situation, the following control is performed:

        Possible Effect without Warning
        Vehicle battery discharges
        Warning Active Condition
        The warning is activated when all of the following conditions are met:
        1. The shift lever is in P*.
        2. The power switch is on (ACC) or on (IG).
        3. The vehicle speed is 0 km/h (0 mph).
        4. The hybrid system is stopped.
        5. The power source is turned off by the automatic power off function (the vehicle remains not operated for 20 minutes with the power switch on (ACC) or for 1 hour with the power switch on (IG)).
        Warning Method
        Combination Meter Assembly
        Buzzer
        -
        Multi-information Display
        The following warning message is displayed for 10 seconds (and then automatically turned off).
        1. AUTO POWER OFF TO CONSERVE BATTERY
        Master Warning Light
        Blinks
        Wireless Door Lock Buzzer
        -
        Warning Stop Condition
        The power switch is turned to a mode other than off.
        *: Precondition

    17. Situation P

      1. A warning message appears on the multi-information display and a buzzer in the combination meter assembly sounds when an electrical key transmitter sub-assembly with a depleted battery is touched to the power switch while depressing the brake.
        In this situation, the following control is performed:

        Possible Effect without Warning
        Malfunction detection
        Warning Active Condition
        Key certification result is OK*.
        Warning Method
        Combination Meter Assembly
        Buzzer
        Sounds once
        Multi-information Display
        The following warning message is displayed for 10 seconds (and then automatically turned off).
        1. DEPRESS BRAKE PEDAL AND PUSH POWER SWITCH TO START
        Master Warning Light
        Blinks
        Wireless Door Lock Buzzer
        -
        Warning Stop Condition
        The warning is stopped when either of the following conditions is met:
        1. The hybrid system is started.
        2. 10 seconds elapsed since the warning massage was displayed.
        3. The electrical key transmitter sub-assembly is detected in the vehicle.
        4. The immobiliser system is set and interior certification stopped or key certification fails.
        *: This situation occurs following Situation L.

  7. Battery Saving

    1. Battery saving preserves the vehicle and key batteries. It is activated when the vehicle remains parked for a long time and when the electrical key transmitter sub-assembly is left inside the exterior actuation area.

      Condition
      Control
      Reinstatement Condition
      When the vehicle remains parked for a long time.
      Control 1:
      1. No response from electrical key transmitter sub-assembly for more than 5 days
        1. Door electrical key antennas and electrical key antenna stop emitting signals for creating the actuation area.
      When the power switch is turned on (IG), the control is canceled and the system is returned to normal.
      Control 2:
      1. No response from electrical key transmitter sub-assembly for more than 14 days
        1. Door electrical key antennas and electrical key antenna stop emitting signals for creating the actuation area.
        2. Front passenger door lock sensor and unlock sensor are disabled.
      When the power switch is turned on (IG), the control is canceled and the system is returned to normal.
      1. When one of the following conditions is met, the control is returned to condition 1:
        1. The doors are locked or unlocked using wireless remote control.
        2. The doors are locked or unlocked by touching the lock/unlock sensor on the driver door.
        3. A door is locked or unlocked using the mechanical key.
        4. Door is opened → closed.
      When the electrical key transmitter sub-assembly is left within the exterior detection area.
      1. This state continues longer than 10 minutes
        1. Electrical key antenna that is detecting the electrical key transmitter sub-assembly stops emitting signals for creating the actuation area.
      1. The control is stopped when one of the following conditions is met:
        1. The doors are locked or unlocked using wireless remote control.
        2. The doors are locked or unlocked by touching the lock/unlock sensor on the front door.
        3. A door is locked or unlocked using the mechanical key.

    2. In addition to the above functions, the auto power off function helps to reduce drain on the vehicle auxiliary battery by turning the power source mode to off (a) when approximately 20 minutes have elapsed since the shift lever was moved to P with the power source mode on (ACC) or (b) when approximately 60 minutes have elapsed since the engine was turned off with the shift lever in P, the power source mode on (IG) and the vehicle stationary.

  8. Key Cancel

    1. The following system functions can be deactivated by using the key cancel operating procedure.

      1. Entry Lock
      2. Entry Unlock
      3. Prevention of Key Confinement
      4. Warning

    2. The system functions can be deactivated by using the following key cancel operating procedure when the power switch is off and the driver door is closed and unlocked.

      Key Cancel operating procedure
      1. The operation procedure is as follows:
        1. Press the unlock button of the electrical key transmitter sub-assembly once.
        2. Within 5 seconds of the step above, open the driver door (Driver Door: Close→Open).
        3. Within 5 seconds of the step above, press the unlock button of the electrical key transmitter sub-assembly twice.
        4. Repeat close → open for the driver door twice* (Driver Door: Open → Close → Open → Close → Open).
        5. Press the unlock button of the electrical key transmitter sub-assembly twice.*
        6. Repeat close → open for the driver door once* (Driver Door: Open → Close → Open).
        7. Within 5 seconds of the step above, close the driver door.
      2. When the cancel procedure is complete, the buzzer sounds twice. Meanwhile, when the procedure is performed again to resume the system, the buzzer sounds once.
      *: Perform all these 3 steps within 30 seconds of the previous step.

  9. Key Code Registration Function

    1. The table below shows the 3 special ID code registration function modes through which up to 7 different codes can be registered. The codes are electronically registered (written to and stored) in the EEPROM. For details, refer to the corresponding Service Bulletin for this model.

      Mode
      Function
      Rewrite
      Clears all previously registered codes and registers only the newly received codes. This mode is used whenever a transmitter or the certification ECU (smart key ECU assembly) is replaced.
      Add
      Adds a newly received code while preserving previously registered codes. This mode is used when adding a new transmitter. If the number of codes exceeds 7, the oldest registered code is cleared first.
      Confirm
      Confirms how many codes are currently registered. When adding a new code, this mode is used to check how many codes already exist.


CONSTRUCTION


  1. Electrical Key Transmitter Sub-assembly

    1. The electrical key transmitter sub-assembly consists of a mechanical key, transmitter for the wireless door lock control, transceiver for the entry function, and transponder chip for the engine immobiliser function.

    2. This mechanical key operates the driver door lock cylinder, but cannot be used to start the hybrid system.

    3. The transmitter for the wireless door lock control has a lock button and unlock button.

    4. The transceiver in the electrical key transmitter sub-assembly receives the signals from the oscillators and returns the ID code of the electrical key transmitter sub-assembly to the door control receiver.



    5. The transponder chip for the engine immobiliser function returns a signal to the power switch as a response to the radio wave received from the power switch.


      Y102230E02


      Text in Illustration 
      *1
      Lock Button
      *2
      Unlock Button
      *3
      Mechanical Key
      -
      -



  2. Power Switch



    1. The power switch consists of a momentary type switch, illumination, antenna coil, and transponder key amplifier.


      Y117496E01



  3. Combination Meter Assembly



    1. When the certification ECU (smart key ECU assembly) detects an abnormality with the smart entry and start system, a message appears on a multi-information display. If the hybrid system is stopped in this state, it might not be possible to restart it.


      Y113726E01


      Text in Illustration 
      *a
      POWER ON display
      *b
      Smart Warning display

      Power Source Condition
      Multi-information Display
      Brake pedal not depressed
      Brake pedal depressed with shift lever in P
      Off
      OFF
      Smart Warning display
      On (ACC), On (IG)
      POWER ON display
      Smart Warning display
      Hybrid System is Operating
      OFF
      OFF


DIAGNOSIS
  1. Start Function

    1. The certification ECU (smart key ECU assembly) can detect malfunctions in the smart entry and start system when the power source is on (IG).

    2. When the ECU detects a malfunction, the multi-information display to warn the driver. At the same time, the ECU stores a 5-digit Diagnostic Trouble Code (DTC) in their memories.

    3. The 5-digit DTCs can be read after connecting the Global TechStream (GTS) to the DLC3.

    4. The smart entry and start system may not operate successfully if a malfunction occurs.