METER / GAUGE SYSTEM > DETAILS



OPERATING CONDITION
  1. Hybrid System Indicator Operation Condition

    1. Hybrid System Indicator is activated when the following conditions are met.

      Condition
      1. Turn the power switch (push start switch) to on (IG).
      2. READY ON state
      3. The shift position is in D or B.


SYSTEM CONTROL


  1. Seat Belt Warning

    1. When the power switch (push start switch) is on (IG), this system detects the condition of the seat belts based on the signals from the front seat belt buckle switch (driver and front passenger) and the weight detector sensor.

    2. The seat belt warning light located in the combination meter assembly is used for both the driver and front passenger seats.

    3. After the power switch (push start switch) is turned on (IG), if the driver or front passenger has not fastened their seat belt, the seat belt warning light will begin flashing.

    4. When the seat belt remains unfastened and the vehicle speed reaches approximately 20 km/h (12.4 mph), the seat belt warning buzzer will start sounding intermittently. At this time, the seat belt warning light flashing will change in sync with the intermittent buzzer sound. These buzzer and indicator warnings will continue for approximately 30 seconds until the seat belt is fastened.

    5. If the seat belt still remains unfastened over the approximately 30 seconds, the intervals of the intermittent buzzer sound and flashing light will change, and such warnings will continue for approximately 90 seconds until the seat belt is fastened.



    6. While the seat belt warning light and buzzer are operating, fastening the seat belt will bring them to a stop.


      Y113905E01


FUNCTION


  1. Combination Meter



    1. The table below shows the combination meter function:


      Y118256E01


      Function
      Outline
      *1
      Speedometer
      Digitally displays the vehicle speed signal in MPH or km/h.
      *2
      Shift Position Indicator
      Displays the shift position.
      *3
      Fuel Gauge
      Displays the remaining fuel amount. Also, displays the indication clearly when cornering or driving on a steep slope by using a software application capable of suppressing any indication deviations.
      *4
      Multi-information Display
      Displays the eco drive monitor, odometer, clock and warning messages etc.
      *5
      Indicator and Warning Lights
      Come on or blink to warn the driver.
      -
      Buzzers
      Sound to warn the driver.



  2. Multi-information Display



    1. The multi-information display consists of a constant display area (see *1 in the illustration below) and content display area (see *2 in the illustration below).


      Y113906E01


      Function
      Outline
      Display Area
      Opening
      System activation animation will be displayed for approximately 3 seconds when the power switch (push start switch) is turned on (IG).
      All
      Eco Drive Monitor
      Energy Monitor, Drive Information, ECO Score, 5min Consumption, ECO Savings, ECO Savings Record, Past Record, and Settings & Screen Off can be selected.
      *2
      Warning Message
      Warning messages interrupt the displayed information to warn the diver.
      *2
      Clock
      Time is displayed.
      *1
      Odometer / Trip Meter
      A travel distance is displayed in the odometer, trip meter A and trip meter B respectively.
      *1
      Average Fuel Consumption
      Average fuel consumption is calculated based on the distance the vehicle has run and the amount of fuel the vehicle has consumed, and then the calculation result is displayed.
      *1
      Ending
      System deactivation animation will be displayed for approximately 3 seconds when the power switch (push start switch) is turned off.
      All
      Cruising Data
      After the ending screen, pieces of information such as a travel distance, time and fuel consumption are displayed.
      *2
      Color Line
      1. The color line varies depending on the content.
        1. Green: Energy Monitor, Drive Information and ECO Score
        2. Pink: ECO Savings and ECO Savings Record
        3. Blue: 5min Consumption and Past Record
        4. Orange: Settings & Screen Off and Warning Message
      *3



    2. The multi-information display flow can be switched as shown in the flow chart below:


      Y113907E01


      Y113908E01


      No.
      Transition Condition
      *1
      Warning message display conditions are met.
      *2
      All warning message displays have finished or All warning message display conditions are canceled.
      *3
      Warning message display conditions are canceled.
      *4
      Door unlock mode transition conditions are met.
      *5
      Door unlock mode settings have been completed.
      *6
      No switch operation has been made for more than approximately 5 seconds.
      *7
      The mode the power switch (push start switch) was turned off the last time will resume when the power switch (push start switch) is turned on (IG). If the mode was Settings & Screen Off when the power switch (push start switch) was turned off the last time, Energy Monitor mode will start from.
      *8
      The mode display will change after approximately 1.5 seconds of the DISP switch being released.
      *9
      DISP switch being pressed and held.
      *10
      The warning message display conditions are met and the DISP switch has not been operated for approximately 10 seconds.
      *11
      All warning message display conditions are canceled.
      *12
      DTC display transition conditions are met.
      *13
      DTC display transition conditions are canceled.



  3. Eco Drive Monitor



    1. The eco drive monitor is displayed in the following order each time the DISP switch of the steering pad switch assembly is pressed.


      Y113909E01


      Text in Illustration 
      *A
      Models for Australia
      -
      -
      *a
      Energy Monitor
      *b
      Drive Information
      *c
      ECO Score
      *d
      5min Consumption
      *e
      ECO Savings
      *f
      ECO Savings Record
      *g
      Past Record
      *h
      Settings & Screen Off
      V100135
      DISP switch being pressed briefly.
      V100136
      Mode display will change after 1.5 seconds of DISP switch being released.
      V100137
      DISP switch being pressed and held.
      -
      -

    2. The table below shows the eco drive monitor function:

      Display Mode
      Display
      Outline
      Energy Monitor
      Y113865
      1. Shows the energy flow in the form of an arrow.
        1. Engine to Tire
        2. Engine to Motor
        3. Motor to Tire
        4. Tire to Motor
        5. Motor to Battery
        6. Battery to Motor
      2. Shows the State Of Charge (SOC) of the HV battery in 8 levels.
      Drive Information
      Y113892
      1. Shows the pieces of information listed below
        1. Average Speed
        2. Driving Time
        3. EV Drive Ratio
        4. EV Traveling Distance
        5. Cruising Range
        6. Outside Temperature
      ECO Score
      Y113867
      1. ECO Score: For every driving cycle that is from a start to a stop, the respective driving conditions of Start, Cruise and Stop are put into calculation to evaluate them, scoring how much the driving control is eco-friendly. Values obtained in this mode do not link to values in ECO Savings mode.
      2. Start: The driving operating conditions, when the vehicle begins to move, are shown in bar graph to indicate how much they are eco-friendly.
      3. Cruise: The driving operating conditions, when the vehicle runs at constant speeds, are shown in bar graph to indicate how much they are eco-friendly.
      4. Stop: The driving operating conditions, when the vehicle decreases to stop, are shown in bar graph to indicate how much they are eco-friendly.
      5. Since Hybrid System Indicator is provided on the same display screen, the driver can see if their driving controls are appropriate to achieve eco-friendly drive further.
      6. Scores will be affected by external circumstances such as road conditions or surrounding environment. However, driving conditions while the cruise control system is active or the shift lever is in N will not be scored.
      5min Consumption
      Y113893
      1. The average fuel consumption, at 5-minute intervals, is calculated from the distance the vehicle has traveled for 5 minutes and the amount of fuel the vehicle has consumed for that travel distance, and the calculation result is expressed with bar graphs.
      2. The momentary fuel consumption is calculated from the travel distance per 20 engine revolutions and the amount of fuel consumed for that travel distance, and the calculation result is expressed with bar graphs.
      ECO Savings (Models for Australia)*1
      Gasoline Price / Basic*2
      Y118257
      1. The total cost of the gasoline consumption corresponding to the travel distance the vehicle actually has been driven is calculated, and then the calculation result is displayed.*4
      2. Since Hybrid System Indicator is provided on the same display screen, the driver can see if their driving controls are appropriate to achieve eco-friendly drive further.
      Gasoline Price / Details*2
      Y113894
      1. The pictogram representing the driver's vehicle shows the fuel consumption cost for a travel distance per unit, and the pictogram moves left or right to express the extent of gasoline consumption amount. (The closer to the left it moves, the less the gasoline is consumed.)
      2. The gasoline consumption cost same as that of the basic display described above is shown.*4
      Fuel Consumption Comparison*3 / Basic*2
      Y113895
      1. The fuel cost difference is calculated by comparing the gasoline consumption cost corresponding to the travel distance the vehicle has actually run with the gasoline consumption cost of the comparison vehicle corresponding to the same travel distance, and then the calculation result is displayed.
      2. Since Hybrid System Indicator is provided on the same display screen, the driver can see if their driving controls are appropriate to achieve eco-friendly drive further.
      Fuel Consumption Comparison*3 / Details*2
      Y113896
      1. The pictogram that represents the comparison vehicle shows the gasoline consumption cost for a travel distance per unit, and the pictogram remains at the reading position.
      2. The pictogram that represents the driver's vehicle shows the fuel consumption cost for a travel distance per unit, and the pictogram moves left or right to express the extent of gasoline consumption difference in comparison with another vehicle. (The closer to the left it moves, the less the gasoline is consumed.)
      3. The gasoline consumption comparison cost same as that of the basic display described above is shown.
      ECO Savings Record (Models for Australia)*5
      Gasoline Price
      Y113897
      The gasoline consumption cost for the current month, last month, 2 months ago, 3 months ago, and 1 year ago is shown in bar graph, and the monthly fuel consumption amounts are shown by quantity.
      Fuel Consumption Comparison
      Y113898
      The difference of the gasoline consumption costs between the driver's vehicle and comparison vehicle for the current month, last month, 2 months ago, 3 months ago, and 1 year ago is shown in bar graph, and the monthly fuel consumption amounts are shown by quantity.
      Past Record*6
      Own Best
      Y113899
      1. The average fuel consumption performances are ranked in the 1st, 2nd and 3rd among the records, and the respective fuel efficiency value, date and travel distance are also displayed.
      2. In addition, when the current performance is within the top 100, the current rank is shown. If the performance is ranked outside the top 100, "Outside Ranking" is displayed.
      Monthly Average
      Y113900
      1. The monthly average fuel consumption for the current month, last month, 2 months ago, 3 months ago, and 1 year ago, is displayed with bar graphs.
      2. The monthly travel distances are also displayed.
      Settings & Screen Off
      Y113877
      1. Allows for setting the preferred multi-information display.
      2. Turns on and off the eco drive monitor.

      HINT:
      *1: Values obtained in this mode do not link to values in ECO Score mode.
      *2: In Settings & Screen Off mode, the Gasoline Price screen and the Fuel Consumption Comparison screen can be switched to either of the displays, Basic or Details.
      *3: If a comparison fuel efficiency value is not set, the Fuel Consumption Comparison screen will not be active.
      *4: The displayed gasoline price will not be identical to the actual gasoline price.
      *5: The values cannot be reset.
      *6: If any one of the fuel consumption values in the odometer, trip meter A or trip meter B are reset, all the fuel consumption values in the meters will be reset together.



  4. Hybrid System Indicator

    1. Hybrid System Indicator will appear when ECO Score mode or ECO Savings mode is selected in the eco drive monitor.

    2. Hybrid System Indicator displays the total of the HV battery and engine output as the hybrid system output.



    3. The scale for Hybrid System Indicator consists of the 3 indicators (Charge, Eco, Power). The role of each indicator is as follows.


      Y113864E01


      Indicator
      Function
      *1
      Charge (CHG)
      This shows that energy regeneration is occurring.
      *2
      Eco
      This indicator is active while the vehicle is driven eco-friendly.
      *3
      Eco (Hybrid Eco)
      This indicator shows that the vehicle is driven in a manner that promotes frequent motor only operation. (Based on the driving conditions, the power management ECU determines if the engine should be stopped to enhance fuel efficiency.)
      *4
      Power (PWR)
      This indicator is on while the drive power is exceeding the eco-friendly driving range (during full power driving etc.).



  5. Settings & Screen Off



    1. To enter the detail setup screen from the Settings & Screen Off screen, the DISP switch needs to be pressed and held.


      Y113910E01


      Text in Illustration 
      *a
      Settings & Screen Off
      *b
      Set ECO Savings
      V100135
      DISP switch being pressed and held.
      -
      -

    2. Settings & Screen Off mode has the setup items listed below. For the Basic Settings, Set ECO Savings and Menu Screen Selection, those can be changed when the vehicle is stationary or the vehicle speed is approximately 8 km/h (5 mph) or less.

      Item
      Customizing Value
      Basic Settings
      Date
      Adjusts a date.
      Clock
      Adjusts a clock.
      Clock Mode
      Selects the 12/24 hour time display mode.
      Steering Switch
      Selects the touch tracer display on/off mode.
      Language
      Selects the display language.
      Set ECO Savings*
      Gasoline Price
      Used to set a gasoline price.
      Fuel Cons. Comparison
      Used to set fuel consumption of a comparison vehicle.
      ECO Savings
      Selects the ECO Savings Basic/Details mode.
      Menu Screen Selection
      ECO Savings Record
      Selects the ECO Savings Record on/off mode.
      5 min. consumption
      Selects the 5 min. consumption on/off mode.
      Past Record
      Changes the Past Record screens.
      Screen Off
      Turns on/off the eco drive monitor.
      Set Clock
      Adjusts a clock.

      1. *: Models for Australia

  6. Warning Message

    1. When a warning is necessary, the warning display interrupts the display in the multi-information display.

    2. The master warning light may illuminate or blink and the buzzer in the combination meter assembly may sound depending on the item in the multi-information display.

    3. When multiple warning conditions occur at the same time, the highest priority warning message is displayed first. After 2 seconds has elapsed, the next highest priority warning message will be shown. Unless the causes of warnings are removed, the respective warning messages continue.

      Priority
      Warning Message
      Master Warning Light
      Buzzer
      1
      MAINTENANCE MODE
      -
      -
      CERTIFICATION MODE
      -
      -
      2
      AUTO POWER OFF TO CONSERVE BATTERY
      -
      -
      3
      SHIFT TO P POSITION
      Blinks
      Sounds
      SHIFT TO P POSITION WHEN PARKED
      Blinks
      Sounds
      TRACTION BATTERY PRESERVATION MODE RESTART AFTER SHIFTING THE P POSITION
      Blinks
      Sounds
      N POSITION
      Blinks
      Sounds
      4
      LOW TRACTION BATTERY CHARGE WHEN NOT IN N POSITION
      Blinks
      Sounds
      RELEASE PARKING BRAKE
      Blinks
      Sounds
      KEY NOT DETECTED
      Blinks
      Sounds
      5
      CHECK HYBRID SYSTEM
      Illuminates
      Sounds
      CHECK CRUISE CONTROL SYSTEM
      Illuminates
      Sounds
      ENGINE OIL PRESSURE LOW
      Illuminates
      Sounds
      CHECK HYBRID SYSTEM STOP THE VEHICLE IN A SAFE PLACE IMMEDIATELY
      Illuminates
      - / Sounds*1
      6
      TURN POWER OFF
      Blinks
      Sounds
      KEY DETECTED IN VEHICLE
      Blinks
      Sounds
      TURN LIGHTS OFF
      Blinks
      Sounds
      DEPRESS BRAKE PEDAL, TOUCH POWER SWITCH WITH KEY
      Blinks
      Sounds
      DEPRESS BRAKE PEDAL AND PUSH POWER SWITCH TO START
      Blinks
      Sounds
      SHIFT TO P POSITION TO START
      Blinks
      Sounds
      7
      STEERING LOCK ACTIVE
      Blinks
      Sounds
      SHIFT TO P POSITION TO START
      Blinks
      Sounds
      8
      KEY BATTERY LOW
      Illuminates
      Sounds
      CHECK HEADLIGHT LEVELING SYSTEM*2
      Illuminates
      Sounds
      HYBRID SYSTEM OVER HEAT OUTPUT POWER IS LIMITED
      Illuminates
      Sounds
      9
      POWER ON
      -
      -
      EV MODE CURRENTLY NOT AVAILABLE
      -
      Sounds
      EV MODE NOT AVAILABLE WARMING UP
      -
      Sounds
      EV MODE NOT AVAILABLE LOW BATTERY
      -
      Sounds
      EV MODE NOT AVAILABLE EXCESSIVE SPEED
      -
      Sounds
      EV MODE NOT AVAILABLE EXCESSIVE ACCELERATION
      -
      Sounds
      EV MODE DEACTIVATED
      -
      Sounds
      EV MODE DEACTIVATED LOW BATTERY
      -
      Sounds
      EV MODE DEACTIVATED EXCESSIVE SPEED
      -
      Sounds
      EV MODE DEACTIVATED EXCESSIVE ACCELERATION
      -
      Sounds

      HINT:
      *1: Depending on the abnormality, the buzzer may sound.
      *2: Models with auto leveling system

  7. Buzzer

    1. The table below shows the warning and reminder functions of the buzzer in the combination meter assembly:

      Priority
      Item
      Priority
      Item
      1
      READY
      2
      Driver Side Seat Belt Warning (a maximum of 5 times)
      3
      Driver Side Seat Belt Warning (Once)
      4
      Passenger Side Seat Belt Warning (Once)
      5
      Seat Belt Warning (Level 2)
      6
      Seat Belt Warning (Level 1)
      7
      Brake System Warning
      8
      EPS Warning
      9
      Door Open Warning When Not in P Position
      10
      Smart Entry and Start System Warning (Intermittent)
      11
      Key Reminder
      12
      Brake Operation Active Check Indication
      13
      Smart Entry and Start System Warning (Intermittent 2)
      14
      Smart Entry and Start System Warning (Once)
      15
      Low Fuel Indicator
      16
      Multi-information Display Warning
      17
      Accelerator Depression with Neutral (N) Selected
      18
      Hybrid System Warning (Intermittent)
      19
      HV Battery Low Warning
      20
      Hybrid System Warning (Once)
      21
      HV Battery Charge Request
      22
      Hybrid System Overheat Warning
      23
      P Position Request at Start
      24
      Immobiliser Certification Reminder
      25
      Parking Brake Engaged Warning
      26
      Door Open while Driving Warning
      27
      EV Drive Mode Reject Warning
      28
      Light Reminder
      29
      Turn Flasher Sound
      -
      -



  8. Dimming Mode Display

    1. The brightness of the combination meter assembly can be adjusted when the taillights are turned on.



    2. While the dimming mode is displayed, the brightness of the meter can be changed by pressing the TRIP switch for 0.8 seconds or more. The brightness of the meter can be adjusted in 4 levels.


      Y113911E01


      Text in Illustration 
      *1
      Multi-information Display
      -
      -
      *a
      Dimming Mode
      *b
      100%
      *c
      12.5%
      *d
      6.25%
      *e
      3.125%
      -
      -


CONSTRUCTION


  1. Steering Pad Switch Assembly



    1. A touch sensor is provided on the following frequently used switches such as the multi-information display, audio system and air conditioning system switches. The touch tracer display is displayed when any of the switches is touched by the driver's finger, and the switch is activated when pressed.

      Steering Pad Switch Assembly
      Touch Sensor
      Audio System
      Volume Switch (+)
      Equipped
      Volume Switch (-)
      Equipped
      MODE Switch
      Equipped
      Seek Switch (Up)
      Equipped
      Seek Switch (Down)
      Equipped
      Multi-information Display
      TRIP Switch
      Equipped
      DISP Switch
      Equipped
      Air Conditioning System
      Air Inlet Control Switch
      Equipped
      TEMP Switch (Up)
      Equipped
      TEMP Switch (Down)
      Equipped
      Bluetooth Hands-free System
      Voice Switch
      Not equipped
      On Hook Switch
      Not equipped
      Off Hook Switch
      Not equipped


      Y118261E01


      Text in Illustration 
      *1
      Steering Pad Switch Assembly
      *2
      Touch Switch Area
      *3
      Function Switch Area
      *4
      Touch Sensor
      *a
      A-A Cross Section
      -
      -