AIRBAG SYSTEM > DETAILS |
| FUNCTION OF MAIN COMPONENTS |
The airbag system mainly consists of the parts listed in the table below.
| Components | Outline | |
| Airbag | Mainly consists of an inflator and a bag. Upon receiving a deployment signal from the airbag sensor assembly, the inflator generates gas to deploy the bag. | |
| Front Seat Outer Belt Assembly | Mainly consists of an inflator and a seat belt. Upon receiving a deployment signal from the airbag sensor assembly, the inflator generates gas to retract the seat belt. | |
| Airbag Sensor | Detects the deceleration of the vehicle during a collision, and transmits the signal to the airbag sensor assembly, from which the airbag sensor assembly determines whether deployment is necessary. | |
| Airbag Sensor Assembly |
| |
| SRS Warning Light | Provided in the combination meter assembly and comes on when the airbag system malfunctions. | |
| Hybrid Vehicle Control ECU |
| |
| OPERATING CONDITION |
Ignition Condition
Deceleration sensors used for the airbag system are installed on various parts on the vehicle and transmit the deceleration data of each part during a collision.
Depending on the situation, the airbag sensor assembly sends a deployment signal to each airbag based on the information from each sensor.
Frontal collision signals are produced based on the information from the airbag sensor assembly and front airbag sensors. The frontal collision signals are used to deploy the SRS driver airbag (horn button assembly), SRS front passenger airbag (instrument panel passenger airbag without door assembly), SRS driver knee airbag (lower No. 1 instrument panel airbag assembly), SRS curtain shield airbag (curtain shield airbag assembly LH/RH) and to activate the seat belt pretensioners.

Side collision signals are produced based on the combined information from the airbag sensor assembly and a side airbag sensor assembly. Side collision signals are used to deploy the SRS side airbag (front seat side airbag assembly)*, SRS curtain shield airbag assembly.

Side rear collision signals are produced based on the combined information from the airbag sensor assembly, a side airbag sensor assembly and No. 2 side airbag sensor assembly. Side rear collision signals are used to deploy the SRS curtain shield airbag assembly.

| SYSTEM CONTROL |
Airbag for Frontal Collision
For frontal collisions, there are 5 airbags and 2 seat belt pretensioners: a SRS driver airbag (horn button assembly), SRS front passenger airbag (instrument panel passenger airbag without door assembly), SRS driver knee airbag (lower No. 1 instrument panel airbag assembly), SRS curtain shield airbag LH (curtain shield airbag assembly LH), SRS curtain shield airbag (curtain shield airbag assembly RH), front seat outer belt assembly LH and front seat outer belt assembly RH. The deployment of the airbags and the activation of the seat belt pretensioners occur simultaneously.

Airbag for Side or Side Rear Collision
For a side collision, if the side airbag sensor assembly detects an impact, it Informs the airbag sensor assembly, and the airbag sensor assembly causes the SRS side airbag (front seat side airbag assembly) and SRS curtain shield airbag (curtain shield airbag assembly) to be deployed and operated simultaneously.

For a side rear collision, if the No. 2 side airbag sensor assembly detects an impact, it informs the airbag sensor assembly via the side airbag sensor assembly, and the airbag sensor assembly causes the SRS curtain shield airbag (curtain shield airbag assembly) to be deployed.

Primary Check Illumination Control
After the power switch is turned ON, the airbag sensor assembly illuminates the SRS warning light in the combination meter assembly for approximately 6 seconds and conducts the primary check. During the primary check, the ignition of airbags is prohibited and a diagnosis of the airbag sensor assembly is performed. If trouble is detected during the primary check, the SRS warning light remains on even after the 6 seconds have elapsed. See the illustration below.

| CONSTRUCTION |
SRS Driver Airbag (Horn Button Assembly) and SRS Front Passenger Airbag (Instrument Panel Passenger Airbag without Door Assembly)
The SRS driver airbag (horn button assembly) and SRS front passenger airbag (instrument panel passenger airbag without door assembly) mainly consist of an inflator and a bag.
SRS Driver Knee Airbag (Lower No. 1 Instrument Panel Airbag Assembly)
The SRS driver knee airbag (lower No. 1 instrument panel airbag assembly) consists of an airbag door, an inflator and a bag.
SRS Curtain Shield Airbag (Curtain Shield Airbag Assembly)
SRS curtain shield airbags (curtain shield airbag assembly LH/RH) that extend from the front pillar to the roof side rail are installed. Each SRS curtain shield airbag (curtain shield airbag assembly) consists of an inflator and a bag.
SRS Side Airbag (Front Seat Side Airbag Assembly)
SRS side airbags (front seat side airbag assembly LH/RH) are installed in the seat backs of the driver seat and the front passenger seat. Each SRS side airbag (front seat side airbag assembly) consists of an inflator, a bag and a cover.
Front Airbag Sensor
A deceleration sensor is enclosed in the front airbag sensor. Based on the deceleration of the vehicle during a front collision, a distortion is created in the sensor and converted into an electrical signal. Accordingly, the extent of the initial collision can be detected in detail.

Side Airbag Sensor Assembly, No. 2 Side Airbag Sensor Assembly
A deceleration sensor is enclosed in the side airbag sensor assembly, No. 2 side airbag sensor assembly. Based on the deceleration of the vehicle during a side or side rear collision, a distortion is created in the sensor and converted into an electrical signal.

| DIAGNOSIS |
If the airbag sensor assembly detects a malfunction in the airbag system, the airbag sensor assembly stores the malfunction data in memory, in addition to illuminating the SRS warning light.
There are 2 types of Diagnostic Trouble Code (DTC) for the airbag system: 5-digit and 2-digit.
The 5-digit DTC can be read by connecting the Techstream to the DLC3.
The 2-digit DTC can be read by connecting SST (09843-18040) to the TC and CG terminals of the DLC3 and reading the blinking of the SRS warning light.
If the SRS airbag deploys, the airbag sensor assembly will turn on the SRS warning light. However, different from the ordinary diagnosis function, a DTC will not be stored. The SRS warning light cannot be turned off. It is necessary to replace the airbag sensor assembly with a new one.
