DTC P0AA6-526 Hybrid Battery Voltage System Isolation Fault |
DTC P0AA6-611 Hybrid Battery Voltage System Isolation Fault |
DTC P0AA6-612 Hybrid Battery Voltage System Isolation Fault |
DTC P0AA6-613 Hybrid Battery Voltage System Isolation Fault |
DTC P0AA6-614 Hybrid Battery Voltage System Isolation Fault |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P0AA6 | 526(*1) | Insulation resistance between the high-voltage circuit and the body has decreased.*2 |
|
| 611 | Insulation resistance of the with motor compressor assembly has decreased.*3 | Air conditioning system | |
| 612 | Insulation resistance of the HV battery area has decreased.*3 |
| |
| 613 | Insulation resistance of the transaxle area has decreased.*3 |
| |
| 614 | Insulation resistance of the high-voltage DC area has decreased.*3 |
|

| *1 | HV Battery | *2 | Battery Smart Unit |
| *3 | SMRB | *4 | SMRG |
| *5 | SMRP | *6 | System Main Resistor |
| *7 | Service Plug Grip | *8 | Inverter with Converter Assembly |
| *9 | Boost Converter | *10 | Inverter |
| *11 | MG1 | *12 | MG2 |
| *13 | Compressor with Motor Assembly | *14 | A/C Inverter |
| *15 | A/C Motor | - | - |
| *a | High-voltage Areas | *b | INF Code 526 Vehicle Insulation Resistance Reduction Area |
| *c | INF Code 611 Air Conditioning System Area | *d | INF Code 612 HV Battery Area |
| *e | INF Code 613 Transaxle Area | *f | INF Code 614 High Voltage Direct Current Area |

| Characteristics of Short Wave Highest Value |
The Data List item Short Wave Highest Val and insulation resistance have the relationship shown in the table below. Short Wave Highest Val decreases with a decrease in insulation resistance. However, in some cases, even though the insulation resistance of the vehicle is normal, Short Wave Highest Val may decrease. Therefore, check Short Wave Highest Val while considering the following.
| Short Wave Highest Value | Trouble Area |
| Neither condition (*1) nor (*2) is met and Short Wave Highest Val is approximately 0 V | Since the insulation resistance is close to 0 Ω, there is a strong possibility of interference with a metal object. |
| Neither condition (*1) nor (*2) is met and Short Wave Highest Val is between 0 and 5 V | Since the insulation resistance is several hundred kilo ohms, there is a strong possibility of the presence of fluid such as water. |
| How to Determine Part with Insulation Malfunction |
Jiggle the high-voltage wire harness to check if the resistance to body ground changes with the position of the wire harness or force applied.
Repeat rotating and stopping of the MG1, MG2 and compressor with motor assembly. Check that the Short Wave Highest Val does not decrease (for example if the motor stops with foreign matter forming a leak path) when the motor stops, or that the Short Wave Highest Val does not return to normal (for example if foreign matter moves away from the leak path) when the motor rotates.
Increase the temperature of MG1and MG2. Check if the Short Wave Highest Val decreases with the temperature increase.
Check that the transaxle fluid is not cloudy as it will become cloudy when mixed with water, resulting in low insulation resistance.
| 1.CHECK DTC OUTPUT (HYBRID CONTROL) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Check if DTCs are output.
| Result | Proceed to |
| P0AA6 only is output. | A |
| P0AA6 and P0A1D (hybrid vehicle control ECU malfunction) are output. | B |
| P0AA6 and P0AA7 (malfunction in the battery smart unit) are output. | C |
| P0AA6 and P0AFC-123, 150 (Hybrid Battery Pack Sensor Module), P0B23-129 (Hybrid Battery "A" Voltage) are output. | D |
Turn the power switch off.
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK INFORMATION CODE |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Access the freeze frame data of DTC P0AA6 and read the INF code.
| Result | Proceed to |
| 526 (decrease in the insulation resistance of the high-voltage circuit) only is output | A |
| 526 and 611 (decrease in the insulation resistance of the air conditioning system area) are output | Refer to the troubleshooting procedures for P0AA6-611 (Air conditioning system) (Click here) |
| 526 and 612 (decrease in the insulation resistance of the battery area) are output | B |
| 526 and 613 (decrease in the insulation resistance of the transaxle area) are output | C |
| 526 and 614 (decrease in the insulation resistance of the high-voltage DC area) are output | D |
Turn the power switch off.
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG2)) |
Check that the service plug grip is not installed.
![]() |
Remove the inverter terminal cover from the inverter with converter assembly.
![]() |
Remove the inverter cover from the inverter with converter assembly.
![]() |
Disconnect the motor cable from the inverter with converter assembly.
| *1 | Motor Cable (MG1) |
| *2 | Motor Cable (MG2) |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
With the shift lever in N and lift up the vehicle.
![]() |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below while rotating the front wheels 2 revolutions in the same direction simultaneously.
| Tester Connection | Switch Condition | Specified Condition |
| a4-3 (V) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| a4-2 (U) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| a4-1 (W) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| *1 | Shield Ground |
| *a | Motor Cable (for MG2) (Inverter with Converter Assembly Side) |
Lower the vehicle and move the shift lever to P.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
|
| ||||
| OK | |
| 4.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG1)) |
Check that the service plug grip is not installed.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
With the shift lever in N and lift up the vehicle.
![]() |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below while rotating the front wheels 2 revolutions in the same direction simultaneously.
| Tester Connection | Switch Condition | Specified Condition |
| a2-3 (V) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| a2-2 (U) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| a2-1 (W) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| *1 | Shield Ground |
| *a | Motor Cable (for MG1) (Inverter with Converter Assembly Side) |
Lower the vehicle and move the shift lever to P.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
|
| ||||
| OK | |
| 5.CHECK NO. 2 ENGINE WIRE (AIR CONDITIONING HARNESS) |
Check that the service plug grip is not installed.
![]() |
Disconnect connector D2 of the No. 2 engine wire (air conditioning harness) from the inverter with converter assembly.
![]() |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D2-1 (ACPB) - Body ground and shield ground | Power switch off | 3 MΩ or higher |
| D2-2 (ACPE) - Body ground and shield ground | Power switch off | 3 MΩ or higher |
| *1 | Shield Ground |
| *a | No. 2 Engine Wire (Air Conditioning Harness) (Inverter with Converter Assembly Side) |
|
| ||||
| OK | |
| 6.CHECK INVERTER WITH CONVERTER ASSEMBLY |
Check that the service plug grip is not installed.
![]() |
Disconnect connector P1 of the frame wire from the inverter with converter assembly.
![]() |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| High voltage terminal - Body ground | Power switch off | 1 MΩ or higher |
| *1 | High Voltage Terminal |
|
| ||||
| OK | |
| 7.CHECK FRAME WIRE |
Check that the service plug grip is not installed.
![]() |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| P1-1 (CEI) - Body ground and shield ground | Power switch off | 10 MΩ or higher |
| P1-2 (CBI) - Body ground and shield ground | Power switch off | 10 MΩ or higher |
| *1 | Shield Ground |
| *a | Frame Wire (Inverter with Converter Assembly Side) |
|
| ||||
| OK | |
| 8.CHECK HV BATTERY AREA |
Check that the service plug grip is not installed.
Remove the No. 1 hybrid battery shield sub-assembly .
![]() |
Disconnect connector z9 from the battery smart unit.
![]() |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - Body ground | Power switch off | 10 MΩ or higher |
| 2 - Body ground | Power switch off | 10 MΩ or higher |
|
| ||||
| OK | ||
| ||
| 9.CHECK INVERTER WITH CONVERTER ASSEMBLY |
Check that the service plug grip is not installed.
![]() |
Remove the inverter terminal cover from the inverter with converter assembly.
![]() |
Remove the inverter cover from the inverter with converter assembly.
![]() |
Disconnect the motor cable from the inverter with converter assembly.
| *1 | Motor Cable (for MG1) |
| *2 | Motor Cable (for MG2) |
![]() |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| High voltage terminal - Body ground | Power switch off | 1 MΩ or higher |
| *1 | High Voltage Terminal |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | ||
| ||
| 10.CHECK HIGH VOLTAGE DIRECT CURRENT AREA |
Check that the service plug grip is not installed.
![]() |
Remove the inverter terminal cover from the inverter with converter assembly.
![]() |
Remove the inverter cover from the inverter with converter assembly.
![]() |
Disconnect connector P1 of the frame wire from the inverter with converter assembly.
![]() |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| P1-1 (CEI) - Body ground and shield ground | Power switch off | 10 MΩ or higher |
| P1-2 (CBI) - Body ground and shield ground | Power switch off | 10 MΩ or higher |
| *1 | Shield Ground |
| *a | Frame Wire (Inverter with Converter Assembly Side) |
|
| ||||
| OK | |
| 11.CHECK NO. 2 ENGINE WIRE (AIR CONDITIONING HARNESS) |
Check that the service plug grip is not installed.
![]() |
Disconnect connector D2 of the No. 2 engine wire (air conditioning harness) from the inverter with converter assembly.
![]() |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D2-1 (ACPB) - Body ground and shield ground | Power switch off | 3 MΩ or higher |
| D2-2 (ACPE) - Body ground and shield ground | Power switch off | 3 MΩ or higher |
| *1 | Shield Ground |
| *a | No. 2 Engine Wire (Air Conditioning Harness) (Inverter with Converter Assembly Side) |
|
| ||||
| OK | ||
| ||
| 12.CHECK NO. 2 ENGINE WIRE (AIR CONDITIONING HARNESS) |
Check that the service plug grip is not installed.
![]() |
Disconnect connector D1 of the No. 2 engine wire (air conditioning harness) from the compressor with motor assembly .
![]() |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D2-1 (ACPB) - Body ground and shield ground | Power switch off | 10 MΩ or higher |
| D2-2 (ACPE) - Body ground and shield ground | Power switch off | 10 MΩ or higher |
| *1 | Shield Ground |
| *a | No. 2 Engine Wire (Air Conditioning Harness) (Inverter with Converter Assembly Side) |
|
| ||||
| OK | ||
| ||
| 13.CHECK FRAME WIRE |
Check that the service plug grip is not installed.
Remove the No. 1 hybrid vehicle battery cover panel LH .
![]() |
Disconnect connector P5 and connector P4 of the frame wire from the hybrid battery junction block assembly.
![]() |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| P4-1 (CEI) - Body ground and shield ground | Power switch off | 10 MΩ or higher |
| P5-1 (CBI) - Body ground and shield ground | Power switch off | 10 MΩ or higher |
| *1 | Shield Ground |
| *a | Frame Wire (Hybrid Battery Junction Bock Assembly Side) |
|
| ||||
| OK | ||
| ||
| 14.CHECK HV BATTERY |
Check that the service plug grip is not installed.
Remove the hybrid battery junction block assembly (Click here).
![]() |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - Battery carrier | Power switch off | 10 MΩ or higher |
| 2 - Battery carrier | Power switch off | 10 MΩ or higher |
| *1 | Battery Carrier |
|
| ||||
| OK | ||
| ||
| 15.CHECK MOTOR CABLE (FOR MG2) |
Check that the service plug grip is not installed.
Disconnect the motor cable (for MG2) from the hybrid vehicle transaxle assembly (Click here).
![]() |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a4-3 (V) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| a4-2 (U) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| a4-1 (W) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| *1 | Shield Ground |
| *a | Motor Cable (for MG2) (Inverter with Converter Assembly Side) |
|
| ||||
| OK | ||
| ||
| 16.CHECK MOTOR CABLE (FOR MG1) |
Check that the service plug grip is not installed.
Disconnect the motor cable (for MG1) from the hybrid vehicle transaxle assembly (Click here).
![]() |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a2-3 (V) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| a2-2 (U) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| a2-1 (W) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| *1 | Shield Ground |
| *a | Motor Cable (for MG1) (Inverter with Converter Assembly Side) |
|
| ||||
| OK | ||
| ||
| 17.CHECK MOTOR CABLE (FOR MG2) |
Turn the power switch off.
Check that the service plug grip is not installed.
Disconnect the motor cable (for MG2) from the hybrid vehicle transaxle assembly (Click here).
![]() |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a4-3 (V) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| a4-2 (U) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| a4-1 (W) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| *1 | Shield Ground |
| *a | Motor Cable (for MG2) (Inverter with Converter Assembly Side) |
|
| ||||
| OK | |
| 18.CHECK MOTOR CABLE (FOR MG1) |
Check that the service plug grip is not installed.
Disconnect the motor cable (for MG1) from the hybrid vehicle transaxle assembly (Click here).
![]() |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a2-3 (V) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| a2-2 (U) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| a2-1 (W) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| *1 | Shield Ground |
| *a | Motor Cable (for MG1) (Inverter with Converter Assembly Side) |
|
| ||||
| OK | ||
| ||