Home › Brake › BRAKE (FRONT) › FRONT BRAKE

FRONT BRAKE > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The following procedure is for the LH side.



1. INSTALL FRONT DISC


    C249590E01
  1. Align the matchmarks of the disc and axle hub, and install the front disc.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    When replacing the disc with a new one, select the installation position where the front disc has minimal runout.



2. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING
  1. Install the front disc brake cylinder mounting to the steering knuckle with the 2 bolts.

    Torque:
    107 N*m{ 1089 kgf*cm , 79 ft.*lbf }



3. INSTALL FRONT DISC BRAKE BUSHING DUST BOOT


    C250561
  1. Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new front disc brake bushing dust boots.
    Text in Illustration 
    V100155
    Lithium Soap Base Glycol Grease

    HINT:
    Apply more than 0.3 g (0.01 oz.) of lithium soap base glycol grease to each front disc brake bushing dust boot.

  1. Install the 2 front disc brake bushing dust boots to the front disc brake cylinder mounting.



4. INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN (for Upper Side)


    C211759
  1. Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the front disc brake cylinder slide pin.
    Text in Illustration 
    V100155
    Lithium Soap Base Glycol Grease

  1. Install the front disc brake cylinder slide pin to the front disc brake cylinder mounting.

  1. Push the front disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.



5. INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSHING


    C211757
  1. Apply a light layer of lithium soap base glycol grease to the contact surface of the front No. 2 disc brake cylinder slide pin (for Lower Side).
    Text in Illustration 
    V100155
    Lithium Soap Base Glycol Grease

  1. Install a new front disc brake cylinder slide bushing to the front disc brake cylinder slide pin (for Lower Side).



6. INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN (for Lower Side)


    C211758
  1. Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the front disc brake cylinder slide pin.
    Text in Illustration 
    V100155
    Lithium Soap Base Glycol Grease

  1. Install the front disc brake cylinder slide pin to the front disc brake cylinder mounting.

  1. Push the front disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.



7. INSTALL FRONT DISC BRAKE FITTING KIT


    C249585E01
  1. Install the 2 front No. 1 disc brake pad support plates and 2 front No. 2 disc brake pad support plates to the front disc brake cylinder mounting.
    Text in Illustration 
    *1
    Front No. 1 Disc Brake Pad Support Plate
    *2
    Front No. 2 Disc Brake Pad Support Plate

    NOTICE:
    Be sure to install each front disc brake pad support plate in the correct position and direction.



8. INSTALL FRONT ANTI-SQUEAL SHIM KIT


    C256881
  1. Install the pad wear indicator plate to each front disc brake pad.

    NOTICE:
    Install each pad wear indicator plate in the correct position and direction.



    C227824E01
  1. Apply disc brake grease to both sides of each front No. 1 anti-squeal shim as shown in the illustration.
    Text in Illustration 
    *A
    Inner
    *B
    Outer
    V100145
    Disc Brake Grease

    NOTICE:
    1. When replacing worn pads, the front anti-squeal shims must be replaced together with the pads.
    2. Apply disc brake grease to the area that contacts the anti-squeal shims.



    C256880E01
  1. Install the front No. 1 anti-squeal shim and front No. 2 anti-squeal shim to each front disc brake pad.
    Text in Illustration 
    *1
    Front No. 1 Anti-squeal Shim
    *2
    Front No. 2 Anti-squeal Shim

    NOTICE:
    1. Install the shims in the correct positions and directions.
    2. Disc brake grease can seep out slightly from the area where the anti-squeal shim is installed.
    3. Make sure that disc brake grease is not applied onto the lining surface.



9. INSTALL FRONT DISC BRAKE PAD


    C249583
  1. Install the 2 front disc brake pads to the front disc brake cylinder mounting.

    NOTICE:
    There should be no oil or grease on the friction surfaces of the disc brake pads or the front disc.



10. INSTALL DISC BRAKE CYLINDER ASSEMBLY


    C249582E01
  1. Hold the front disc brake cylinder slide pin, and install the disc brake cylinder assembly to the front disc brake cylinder mounting with the 2 bolts.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }



11. CONNECT FRONT FLEXIBLE HOSE


    C249580E01
  1. Connect the front flexible hose to the disc brake cylinder assembly with a new union bolt and a new gasket.
    Text in Illustration 
    *a
    Lock Hole

    Torque:
    30 N*m{ 310 kgf*cm , 22 ft.*lbf }

    HINT:
    Install the flexible hose lock securely into the lock hole in the disc brake cylinder.



12. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
  1. Connect the cable to the negative (-) auxiliary battery terminal .

  1. Perform the following procedure if air bleeding is not necessary:

    1. Connect the reservoir level switch connector.

    2. Clear the DTCs (Click here).



13. BLEED BRAKE LINE


  1. Separate the center No. 1 cowl top ventilator louver.



      C250009
    1. for LHD:
      Disengage the 4 claws and 6 guides, and separate the center No. 1 cowl top ventilator louver.



    2. C249823
    3. for RHD:
      Disengage the 3 claws and 5 guides, and separate the center No. 1 cowl top ventilator louver.



  1. Bleed brake line.



    1. Remove the brake master cylinder reservoir filler cap assembly.


      C256188E01


      Text in Illustration 
      *A
      for LHD
      *B
      for RHD

    2. Add brake fluid into the reservoir between the MAX and MIN lines on the brake fluid reservoir.

      Brake fluid:
      SAE J1703 or FMVSS No. 116 DOT3

    3. Connect the intelligent tester to the DLC3 and turn the power switch on (IG).

    4. Turn the intelligent tester on and enter the following menus: Chassis / ABS/VSC/TRC / Air Bleeding.

    5. Select "Usual air bleeding" on the intelligent tester display, and bleed air from the brake fluid following the instructions on the intelligent tester.

    6. After air bleeding, tighten each bleeder plug.

      Torque:
      front bleeder plug:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
      rear bleeder plug:
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    7. Clear the DTCs (Click here).

    8. Turn the intelligent tester off and turn the power switch off.

    9. Install the brake master cylinder reservoir filler cap.

  1. Inspect for brake fluid leaks.

  1. Install the center No. 1 cowl top ventilator louver.

    1. for LHD:
      Engage the 4 claws and 6 guides to install the center No. 1 cowl top ventilator louver.

    2. for RHD:
      Engage the 3 claws and 5 guides to install the center No. 1 cowl top ventilator louver.



14. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }