Home › Engine / Hybrid System › 1NZ-FXE ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > TERMINALS OF ECM

for Preparation Click here



A262466E05

HINT:
The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


for LHD 
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A40-1 (BATT) - C10-16 (E1)
Y - W-B
Auxiliary battery (for measuring auxiliary battery voltage and for ECM memory)
Power switch off
11 to 16 V
A40-2 (+B) - C10-16 (E1)
B - W-B
Power source of ECM
Power switch on (IG)
11 to 14 V
A40-3 (+B2) - C10-16 (E1)
B - W-B
Power source of ECM
Power switch on (IG)
11 to 14 V
C10-29 (+BM) - C10-16 (E1)
BR - W-B
Power source of throttle actuator
Power switch off
11 to 16 V
A40-37 (IGSW) - C10-16 (E1)
P - W-B
Power switch on (IG) signal
Power switch on (IG)
11 to 14 V
C10-75 (OC1+) - C10-74 (OC1-)
BR - GR
Camshaft timing oil control valve assembly operation signal
Idling
Pulse generation
(See waveform 1)
A40-46 (MREL) - C10-16 (E1)
GR - W-B
EFI-MAIN relay operation signal
Power switch on (IG)
11 to 14 V
C10-91 (VG) - C10-92 (E2G)
R - L
Mass air flow meter sub-assembly signal
Idling, shift lever in P, A/C switch off
0.5 to 3.0 V
C10-90 (THA) - C10-122 (ETHA)
P - G
Intake air temperature sensor signal
Idling, intake air temperature 20°C (68°F)
0.5 to 3.4 V
C10-93 (THW) - C10-94 (ETHW)
L - BR
Engine coolant temperature sensor signal
Idling, engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
C10-115 (VCTA) - C10-116 (ETA)
W - V
Power source of throttle position sensor (specific voltage)
Power switch on (IG)
4.5 to 5.5 V
C10-84 (VTA1) - C10-116 (ETA)
Y - V
Throttle position sensor signal (for engine control)
Accelerator pedal fully released
0.5 to 1.1 V
C10-83 (VTA2) - C10-116 (ETA)
GR - V
Throttle position sensor signal (for sensor malfunction detection)
Accelerator pedal fully released
2.1 to 3.1 V
C10-23 (HA1A) - C10-52 (E04)
G - W-B
Air fuel ratio sensor heater operation signal
Idling
Pulse generation
(See waveform 2)
Power switch on (IG)
11 to 14 V
C10-133 (A1A+) - C10-16 (E1)
R - W-B
Air fuel ratio sensor signal
Power switch on (IG)
3.3 V*
C10-134 (A1A-) - C10-16 (E1)
G - W-B
Air fuel ratio sensor signal
Power switch on (IG)
2.9 V*
C10-22 (HT1B) - C10-52 (E04)
L - W-B
Heated oxygen sensor heater operation signal
Idling
Below 3.0 V
Power switch on (IG)
11 to 14 V
C10-103 (OX1B) - C10-135 (EX1B)
L - P
Heated oxygen sensor signal
Engine speed maintained at 2500 rpm for 2 minutes after warming up engine
Pulse generation
(See waveform 3)
C10-20 (#10) - C10-51 (E01)
GR - BR
No. 1 fuel injector assembly signal
Power switch on (IG)
11 to 14 V
Idling
Pulse generation
(See waveform 4)
C10-17 (#20) - C10-51 (E01)
P - BR
No. 2 fuel injector assembly signal
Power switch on (IG)
11 to 14 V
Idling
Pulse generation
(See waveform 4)
C10-18 (#30) - C10-51 (E01)
L - BR
No. 3 fuel injector assembly signal
Power switch on (IG)
11 to 14 V
Idling
Pulse generation
(See waveform 4)
C10-19 (#40) - C10-51 (E01)
Y - BR
No. 4 fuel injector assembly signal
Power switch on (IG)
11 to 14 V
Idling
Pulse generation
(See waveform 4)
C10-123 (KNK1) - C10-124 (EKNK)
R - G
Knock control sensor signal
Engine speed maintained at 2500 rpm after warming up engine
Pulse generation
(See waveform 5)
C10-82 (VV1+) - C10-114 (VV1-)
L - W
Cam position sensor signal
Idling
Pulse generation
(See waveform 6)
C10-78 (NE+) - C10-110 (NE-)
G - R
Crank position sensor signal
Idling
Pulse generation
(See waveform 6)
A40-43 (G2O) - C10-16 (E1)
B - W-B
Camshaft revolution signal
Idling
Pulse generation
(See waveform 7)
C10-57 (IGT1) - C10-16 (E1)
W - W-B
No. 1 ignition coil assembly (ignition signal)
Idling
Pulse generation
(See waveform 8)
C10-56 (IGT2) - C10-16 (E1)
V - W-B
No. 2 ignition coil assembly (ignition signal)
Idling
Pulse generation
(See waveform 8)
C10-55 (IGT3) - C10-16 (E1)
G - W-B
No. 3 ignition coil assembly (ignition signal)
Idling
Pulse generation
(See waveform 8)
C10-54 (IGT4) - C10-16 (E1)
LG - W-B
No. 4 ignition coil assembly (ignition signal)
Idling
Pulse generation
(See waveform 8)
C10-102 (IGF1) - C10-16 (E1)
Y - W-B
Ignition coil assembly (ignition confirmation signal)
Power switch on (IG)
4.5 to 5.5 V
Idling
Pulse generation
(See waveform 8)
C10-76 (PRG) - C10-51 (E01)
L - BR
Purge VSV operation signal
Power switch on (IG)
11 to 14 V
Idling, under purge control
Pulse generation
(See waveform 9)
C10-60 (M+) - C10-59 (ME01)
W - BR
Throttle actuator operation signal
(positive terminal)
Idling with warm engine
Pulse generation
(See waveform 10)
C10-30 (M-) - C10-59 (ME01)
B - BR
Throttle actuator operation signal
(negative terminal)
Idling with warm engine
Pulse generation
(See waveform 11)
A40-21 (FC) - C10-51 (E01)
R - BR
Fuel pump control
Power switch on (IG)
11 to 14 V
A40-27 (W) - C10-16 (E1)
B - W-B
Malfunction Indicator Lamp (MIL) operation signal
Power switch on (IG)
(MIL goes on)
Below 3.0 V
Idling
11 to 14 V
A40-23 (TC) - C10-16 (E1)
P - W-B
Terminal TC of DLC3
Power switch on (IG)
11 to 14 V
A40-31 (TACH) - C10-16 (E1)
LG - W-B
Engine speed signal
Idling
Pulse generation
(See waveform 12)
A40-13 (CANH) - C10-16 (E1)
L - W-B
CAN communication line
Power switch on (IG)
Pulse generation
(See waveform 13)
A40-26 (CANL) - C10-16 (E1)
W - W-B
CAN communication line
Power switch on (IG)
Pulse generation
(See waveform 14)
A40-12 (CANP) - C10-16 (E1)
B - W-B
CAN communication line
Power switch on (IG)
Pulse generation
(See waveform 13)
A40-25 (CANN) - C10-16 (E1)
W - W-B
CAN communication line
Power switch on (IG)
Pulse generation
(See waveform 14)
A40-28 (WPI) - C10-16 (E1)
G - W-B
Engine water pump assembly signal
Idling with warm engine
Pulse generation
(See waveform 15)
A40-29 (WPO) - C10-16 (E1)
L - W-B
Engine water pump assembly signal
Idling with warm engine
Pulse generation
(See waveform 16)
C10-118 (VCPM) - C10-119 (EPIM)
P - LG
Power source of manifold absolute pressure sensor
Power switch on (IG)
4.75 to 5.25 V
C10-87 (PIM) - C10-119 (EPIM)
B - LG
Manifold absolute pressure sensor signal
Power switch on (IG)
3.0 to 5.0 V
C10-28 (EGR1) - C10-16 (E1)
R - W-B
EGR valve assembly
EGR valve operating
Pulse generation
(See waveform 17)
C10-27 (EGR2) - C10-16 (E1)
G - W-B
EGR valve assembly
EGR valve operating
Pulse generation
(See waveform 17)
C10-26 (EGR3) - C10-16 (E1)
W - W-B
EGR valve assembly
EGR valve operating
Pulse generation
(See waveform 17)
C10-25 (EGR4) - C10-16 (E1)
Y - W-B
EGR valve assembly
EGR valve operating
Pulse generation
(See waveform 17)
A40-45 (RFC) - C10-16 (E1)
LG - W-B
Cooling fan control
Power switch on (IG), A/C switch on (max cool)
Pulse generation
(See waveform 18)
A40-50 (EC) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
C10-16 (E1) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
C10-51 (E01) - Body ground
BR - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
C10-21 (E02) - Body ground
B - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
C10-52 (E04) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
C10-59 (ME01) - Body ground
BR - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
C10-58 (GE01) - Body ground
BR - -
Shielded earth (ground) circuit of throttle actuator
Always
Below 1 Ω

for RHD 
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A40-1 (BATT) - C9-16 (E1)
Y - W-B
Auxiliary battery (for measuring auxiliary battery voltage and for ECM memory)
Power switch off
11 to 16 V
A40-2 (+B) - C9-16 (E1)
B - W-B
Power source of ECM
Power switch on (IG)
11 to 14 V
A40-3 (+B2) - C9-16 (E1)
B - W-B
Power source of ECM
Power switch on (IG)
11 to 14 V
C9-29 (+BM) - C9-16 (E1)
BR - W-B
Power source of throttle actuator
Power switch off
11 to 16 V
A40-37 (IGSW) - C9-16 (E1)
P - W-B
Power switch on (IG) signal
Power switch on (IG)
11 to 14 V
C9-75 (OC1+) - C9-74 (OC1-)
BR - GR
Camshaft timing oil control valve assembly operation signal
Idling
Pulse generation
(See waveform 1)
A40-46 (MREL) - C9-16 (E1)
GR - W-B
EFI-MAIN relay operation signal
Power switch on (IG)
11 to 14 V
C9-91 (VG) - C9-92 (E2G)
R - L
Mass air flow meter sub-assembly signal
Idling, shift lever in P, A/C switch off
0.5 to 3.0 V
C9-90 (THA) - C9-122 (ETHA)
P - G
Intake air temperature sensor signal
Idling, intake air temperature 20°C (68°F)
0.5 to 3.4 V
C9-93 (THW) - C9-94 (ETHW)
L - BR
Engine coolant temperature sensor signal
Idling, engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
C9-115 (VCTA) - C9-116 (ETA)
W - V
Power source of throttle position sensor (specific voltage)
Power switch on (IG)
4.5 to 5.5 V
C9-84 (VTA1) - C9-116 (ETA)
Y - V
Throttle position sensor signal (for engine control)
Accelerator pedal fully released
0.5 to 1.1 V
C9-83 (VTA2) - C9-116 (ETA)
GR - V
Throttle position sensor signal (for sensor malfunction detection)
Accelerator pedal fully released
2.1 to 3.1 V
C9-23 (HA1A) - C9-52 (E04)
G - W-B
Air fuel ratio sensor heater operation signal
Idling
Pulse generation
(See waveform 2)
Power switch on (IG)
11 to 14 V
C9-133 (A1A+) - C9-16 (E1)
R - W-B
Air fuel ratio sensor signal
Power switch on (IG)
3.3 V*
C9-134 (A1A-) - C9-16 (E1)
G - W-B
Air fuel ratio sensor signal
Power switch on (IG)
2.9 V*
C9-22 (HT1B) - C9-52 (E04)
L - W-B
Heated oxygen sensor heater operation signal
Idling
Below 3.0 V
Power switch on (IG)
11 to 14 V
C9-103 (OX1B) - C9-135 (EX1B)
L - P
Heated oxygen sensor signal
Engine speed maintained at 2500 rpm for 2 minutes after warming up engine
Pulse generation
(See waveform 3)
C9-20 (#10) - C9-51 (E01)
GR - BR
No. 1 fuel injector assembly signal
Power switch on (IG)
11 to 14 V
Idling
Pulse generation
(See waveform 4)
C9-17 (#20) - C9-51 (E01)
P - BR
No. 2 fuel injector assembly signal
Power switch on (IG)
11 to 14 V
Idling
Pulse generation
(See waveform 4)
C9-18 (#30) - C9-51 (E01)
L - BR
No. 3 fuel injector assembly signal
Power switch on (IG)
11 to 14 V
Idling
Pulse generation
(See waveform 4)
C9-19 (#40) - C9-51 (E01)
Y - BR
No. 4 fuel injector assembly signal
Power switch on (IG)
11 to 14 V
Idling
Pulse generation
(See waveform 4)
C9-123 (KNK1) - C9-124 (EKNK)
R - G
Knock control sensor signal
Engine speed maintained at 2500 rpm after warming up engine
Pulse generation
(See waveform 5)
C9-82 (VV1+) - C9-114 (VV1-)
L - W
Cam position sensor signal
Idling
Pulse generation
(See waveform 6)
C9-78 (NE+) - C9-110 (NE-)
G - R
Crank position sensor signal
Idling
Pulse generation
(See waveform 6)
A40-43 (G2O) - C9-16 (E1)
B - W-B
Camshaft revolution signal
Idling
Pulse generation
(See waveform 7)
C9-57 (IGT1) - C9-16 (E1)
W - W-B
No. 1 ignition coil assembly (ignition signal)
Idling
Pulse generation
(See waveform 8)
C9-56 (IGT2) - C9-16 (E1)
V - W-B
No. 2 ignition coil assembly (ignition signal)
Idling
Pulse generation
(See waveform 8)
C9-55 (IGT3) - C9-16 (E1)
G - W-B
No. 3 ignition coil assembly (ignition signal)
Idling
Pulse generation
(See waveform 8)
C9-54 (IGT4) - C9-16 (E1)
LG - W-B
No. 4 ignition coil assembly (ignition signal)
Idling
Pulse generation
(See waveform 8)
C9-102 (IGF1) - C9-16 (E1)
Y - W-B
Ignition coil assembly (ignition confirmation signal)
Power switch on (IG)
4.5 to 5.5 V
Idling
Pulse generation
(See waveform 8)
C9-76 (PRG) - C9-51 (E01)
L - BR
Purge VSV operation signal
Power switch on (IG)
11 to 14 V
Idling, under purge control
Pulse generation
(See waveform 9)
C9-60 (M+) - C9-59 (ME01)
W - BR
Throttle actuator operation signal
(positive terminal)
Idling with warm engine
Pulse generation
(See waveform 10)
C9-30 (M-) - C9-59 (ME01)
B - BR
Throttle actuator operation signal
(negative terminal)
Idling with warm engine
Pulse generation
(See waveform 11)
A40-21 (FC) - C9-51 (E01)
R - BR
Fuel pump control
Power switch on (IG)
11 to 14 V
A40-27 (W) - C9-16 (E1)
B - W-B
Malfunction Indicator Lamp (MIL) operation signal
Power switch on (IG)
(MIL goes on)
Below 3.0 V
Idling
11 to 14 V
A40-23 (TC) - C9-16 (E1)
P - W-B
Terminal TC of DLC3
Power switch on (IG)
11 to 14 V
A40-31 (TACH) - C9-16 (E1)
LG - W-B
Engine speed signal
Idling
Pulse generation
(See waveform 12)
A40-13 (CANH) - C9-16 (E1)
L - W-B
CAN communication line
Power switch on (IG)
Pulse generation
(See waveform 13)
A40-26 (CANL) - C9-16 (E1)
W - W-B
CAN communication line
Power switch on (IG)
Pulse generation
(See waveform 14)
A40-12 (CANP) - C9-16 (E1)
B - W-B
CAN communication line
Power switch on (IG)
Pulse generation
(See waveform 13)
A40-25 (CANN) - C9-16 (E1)
W - W-B
CAN communication line
Power switch on (IG)
Pulse generation
(See waveform 14)
A40-28 (WPI) - C9-16 (E1)
G - W-B
Engine water pump assembly signal
Idling with warm engine
Pulse generation
(See waveform 15)
A40-29 (WPO) - C9-16 (E1)
L - W-B
Engine water pump assembly signal
Idling with warm engine
Pulse generation
(See waveform 16)
C9-118 (VCPM) - C9-119 (EPIM)
P - LG
Power source of manifold absolute pressure sensor
Power switch on (IG)
4.75 to 5.25 V
C9-87 (PIM) - C9-119 (EPIM)
B - LG
Manifold absolute pressure sensor signal
Power switch on (IG)
3.0 to 5.0 V
C9-28 (EGR1) - C9-16 (E1)
R - W-B
EGR valve assembly
EGR valve operating
Pulse generation
(See waveform 17)
C9-27 (EGR2) - C9-16 (E1)
G - W-B
EGR valve assembly
EGR valve operating
Pulse generation
(See waveform 17)
C9-26 (EGR3) - C9-16 (E1)
W - W-B
EGR valve assembly
EGR valve operating
Pulse generation
(See waveform 17)
C9-25 (EGR4) - C9-16 (E1)
Y - W-B
EGR valve assembly
EGR valve operating
Pulse generation
(See waveform 17)
A40-45 (RFC) - C9-16 (E1)
LG - W-B
Cooling fan control
Power switch on (IG), A/C switch on (max cool)
Pulse generation
(See waveform 18)
A40-50 (EC) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
C9-16 (E1) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
C9-51 (E01) - Body ground
BR - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
C9-21 (E02) - Body ground
B - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
C9-52 (E04) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
C9-59 (ME01) - Body ground
BR - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
C9-58 (GE01) - Body ground
BR - -
Shielded earth (ground) circuit of throttle actuator
Always
Below 1 Ω
*: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

WAVEFORM 1
A093229E38
Camshaft Timing Oil Control Valve Assembly Signal 
ECM Terminal Name
Between OC1+ and OC1-
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling

WAVEFORM 2
A205412E01
Air Fuel Ratio Sensor (Sensor 1) Heater Operation Signal 
ECM Terminal Name
Between HA1A and E04
Tester Range
5 V/DIV., 10 ms./DIV.
Condition
Idling

HINT:
The wavelength varies in accordance with the engine operating condition.


WAVEFORM 3
A088863E15
Heated Oxygen Sensor (Sensor 2) Signal 
ECM Terminal Name
Between OX1B and EX1B
Tester Range
0.2 V/DIV., 200 ms./DIV.
Condition
Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:
In the Data List, the item O2S B1S2 shows the values input to the ECM from the heated oxygen sensor.


WAVEFORM 4
A093279E24
No. 1 (to No. 4) Fuel Injector Assembly Signal 
ECM Terminal Name
Between #10 (to #40) and E01
Tester Range
20 V/DIV., 20 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 5
A085286E82
Knock Control Sensor Signal 
ECM Terminal Name
Between KNK1 and EKNK
Tester Range
1 V/DIV., 1 ms./DIV.
Condition
Engine speed maintained at 2500 rpm after warming up engine

HINT:
  1. The wavelength becomes shorter as the engine speed increases.
  2. The waveforms and amplitudes displayed differ slightly depending on the vehicle condition.


WAVEFORM 6
A063955E59
Crank Position Sensor and Cam Position Sensor Signal 
ECM Terminal Name
CH1: Between VV1+ and VV1-
CH2: Between NE+ and NE-
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 7
A214025E01
Camshaft Revolution Signal from ECM to Certification ECU (Smart Key ECU Assembly) and Inverter with Converter Assembly 
ECM Terminal Name
Between G2O and E1
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 8
A122717E25
Ignition Coil Assembly Signal (IGT and IGF Signal) 
ECM Terminal Name
CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range
2 V/DIV., 20 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 9
A218020E01
Purge VSV Signal 
ECM Terminal Name
Between PRG and E01
Tester Range
10 V/DIV., 20 ms./DIV.
Condition
Idling, under purge control

HINT:
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.


WAVEFORM 10
A208000E03
Throttle Actuator Positive Terminal Signal 
ECM Terminal Name
Between M+ and ME01
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 11
A245848E01
Throttle Actuator Negative Terminal Signal 
ECM Terminal Name
Between M- and ME01
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 12
A093225E33
Engine Speed Signal 
ECM Terminal Name
Between TACH and E1
Tester Range
5 V/DIV., 10 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 13
A086154E48
CAN Communication Signal (Reference) 
ECM Terminal Name
Between CANH and E1, or CANP and E1
Tester Range
1 V/DIV., 10 μs./DIV.
Condition
Power switch on (IG)

HINT:
The waveform varies depending on the CAN communication signal.


WAVEFORM 14
A086155E44
CAN Communication Signal (Reference) 
ECM Terminal Name
Between CANL and E1, or CANN and E1
Tester Range
1 V/DIV., 10 μs./DIV.
Condition
Power switch on (IG)

HINT:
The waveform varies depending on the CAN communication signal.


WAVEFORM 15
A214025E01
Engine Water Pump Assembly Signal (from Engine Water Pump Assembly to ECM) 
ECM Terminal Name
Between WPI and E1
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Idling with warm engine

HINT:
The wavelength becomes shorter as the engine water pump assembly speed increases.


WAVEFORM 16
A214025E01
Engine Water Pump Assembly Signal (from ECM to Engine Water Pump Assembly) 
ECM Terminal Name
Between WPO and E1
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Idling with warm engine

HINT:
The wavelength becomes shorter as the engine water pump assembly speed increases.


WAVEFORM 17
A214026E01
EGR Valve Assembly Signal 
ECM Terminal Name
Between EGR1 and E1
Between EGR2 and E1
Between EGR3 and E1
Between EGR4 and E1
Tester Range
20 V/DIV., 50 ms./DIV.
Condition
EGR valve operating

WAVEFORM 18
A247290E02
Cooling Fan Control Signal 
ECM Terminal Name
Between RFC and E1
Tester Range
1 V/DIV., 2 ms./DIV.
Condition
Power switch on (IG), A/C switch on (max cool)

HINT:
The wavelength becomes shorter as the engine coolant temperature.