Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuator and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / (desired system) / Data List.

  5. Read the Data List according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Dimmer SW
    Dimmer switch high position signal/ON or OFF
    ON: Dimmer switch in high or high flash position
    OFF: Dimmer switch in low position
    -
    Passing Light SW
    Dimmer switch high flash position (pass) signal/ON or OFF
    ON: Dimmer switch in high flash position
    OFF: Dimmer switch not in high flash position
    -
    Rear Fog Light SW*1
    Rear fog light switch signal/ON or OFF
    ON: Rear fog light switch on
    OFF: Rear fog light switch off
    -
    Front Fog Light SW
    Front fog light switch signal/ON or OFF
    ON: Front fog light switch on
    OFF: Front fog light switch off
    -
    Head Light SW (Head)
    Light control switch head position signal/ON or OFF
    ON: Light control switch in head position
    OFF: Light control switch not in head position
    -
    Head Light SW (Tail)
    Light control switch tail position signal/ON or OFF
    ON: Light control switch in tail or head position
    OFF: Light control switch in neither tail nor head position
    -

    1. *1: w/ Rear Fog Light

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Turn Signal Switch (Right)
    Turn signal switch (Right) signal/ON or OFF
    ON: Turn signal switch (Right) on
    OFF: Turn signal switch (Right) off
    -
    Turn Signal Switch (Left)
    Turn signal switch (Left) signal/ON or OFF
    ON: Turn signal switch (Left) on
    OFF: Turn signal switch (Left) off
    -
    Hazard Flasher Switch
    Hazard switch signal/ON or OFF
    ON: Hazard switch on
    OFF: Hazard switch off
    -


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Main Body / Active Test.

  5. Perform the Active Test according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Taillight Relay
    Taillight relay
    ON/OFF
    -
    Headlight Relay
    Headlight relay (low beam headlights)
    ON/OFF
    -
    Head Light Hi
    High beam headlights
    ON/OFF
    -
    Front Fog Light Relay
    Front fog light relay
    ON/OFF
    Light control switch is in tail position
    Rear Fog Light Relay*1
    Rear fog light relay
    ON/OFF
    Light control switch is in tail position

    1. *1: w/ Rear Fog Light