Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > Cruise Control Switch Circuit

for Preparation Click here


DESCRIPTION

The cruise control switch is used to turn the cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact points of the cruise control switch turn on with switch operation. Then the hybrid vehicle control ECU reads the voltage value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL.

WIRING DIAGRAM


B373913E02


INSPECTION PROCEDURE

1.READ VALUE ON INTELLIGENT TESTER
E107091E21
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Select the following menu items: Powertrain / Cruise Control / Data List.

  1. Check the Data List to confirm proper functioning of the cruise control switch.
    Text in Illustration 
    *a
    ON-OFF
    *b
    -/SET
    *c
    +/RES
    *d
    CANCEL

    Cruise Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Main SW M-CPU
    Cruise control switch signal (Main CPU) / ON or OFF
    ON: Cruise control switch (ON-OFF button) pushed
    OFF: Cruise control switch (ON-OFF button) released
    -
    Cancel Switch
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST Switch
    -/SET switch signal / ON or OFF
    ON: -/SET switch on
    OFF: -/SET switch off
    -
    RES/ACC Switch
    +/RES switch signal / ON or OFF
    ON: +/RES switch on
    OFF: +/RES switch off
    -
    Main SW S-CPU
    Cruise control switch signal (Sub CPU) / ON or OFF
    ON: Cruise control switch (ON-OFF button) pushed
    OFF: Cruise control switch (ON-OFF button) released
    -

    OK:
    When the cruise control switch is operated, the display changes as shown above.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT CRUISE CONTROL SWITCH
  1. Remove the cruise control switch (Click here).



  1. Measure the resistance according to the value(s) in the table below.


    E144930E19


Text in Illustration 
*1
Cruise Control Switch (ON-OFF button)
-
-
*a
Component without harness connected
(Cruise Control Switch)
*b
ON-OFF
*c
+/RES
*d
-/SET
*e
CANCEL
-
-

Standard Resistance:

Tester Connection
Switch Condition
Specified Condition
1 - 3
Cruise control switch (ON-OFF button) released
1 MΩ or higher
Cruise control switch (ON-OFF button) pushed
Below 2.5 Ω
+/RES
235 to 245 Ω
-/SET
617 to 643 Ω
CANCEL
1509 to 1571 Ω



NG
REPLACE CRUISE CONTROL SWITCH (Click here)
OK


3.CHECK CRUISE CONTROL SWITCH WIRE (SPIRAL CABLE SUB-ASSEMBLY - CRUISE CONTROL SWITCH)
E229996E05
  1. Disconnect the spiral with sensor cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Specified Condition
    z6-3 - 3
    Below 1 Ω
    z6-4 - 1
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Spiral with Sensor Cable Sub-assembly)
    *b
    Front view of wire harness connector
    (to Cruise Control Switch)



NG
REPAIR OR REPLACE CRUISE CONTROL SWITCH WIRE (SPIRAL CABLE SUB-ASSEMBLY - CRUISE CONTROL SWITCH)
OK


4.CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY
E149009E06

NOTICE:
The spiral with sensor cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral with sensor cable sub-assembly may prevent the airbag from deploying. Be sure to read the pages shown in the brackets.

HINT:
  1. Removal (Click here)
  2. Installation (Click here)

  1. Remove the spiral with sensor cable sub-assembly.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
z6-3 - G5-1 (CCS)
Center
Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right
z6-4 - G5-2 (ECC)
Center
Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right

  1. After setting the spiral with sensor cable sub-assembly to the center position, rotate the spiral with sensor cable sub-assembly 2.5 times clockwise. Then while rotating the spiral with sensor cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    z6-3 - G5-1 (CCS)
    Always
    Below 3 Ω
    z6-4 - G5-2 (ECC)
    Always
    Below 3 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Spiral with Sensor Cable Sub-assembly)

    HINT:
    The spiral with sensor cable sub-assembly makes a maximum of approximately 5 rotations.



NG
REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SPIRAL CABLE SUB-ASSEMBLY)
  1. Disconnect the G57 hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    G5-1 (CCS) - G57-28 (CCS)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    G5-1 (CCS) or G57-28 (CCS) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
OK


6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)


    E171248E28
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    G5-2 (ECC) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Spiral with Sensor Cable Sub-assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
OK

REPLACE HYBRID CONTROL ECU (Click here)