SHIFT LEVER POSITION SENSOR > INSTALLATION |
| 1. INSTALL SHIFT LEVER POSITION SENSOR |
![]() |
Using SST and a hammer, tap in a new shift lever position sensor seal.
Install the shift lever position sensor to the manual valve shaft.
Temporarily install the 2 bolts.
Install the lock plate and tighten the nut.
Temporarily install the control shaft lever to the manual valve shaft.
![]() |
Turn the lever clockwise until it stops, then turn it counterclockwise 2 notches.
Remove the control shaft lever from the manual valve shaft.
![]() |
Align the protruding part with the neutral basic line.
| *a | Neutral Basic Line |
| *b | Protruding |
| *c | Range of Play |
![]() |
Tighten the 2 bolts in the order shown in the illustration.
Using a screwdriver, secure the nut with the lock plate.
Install the control shaft lever, washer, and nut to the manual valve shaft.
Connect the connector to the shift lever position sensor.
| 2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.
Install the transmission control cable assembly to the control shaft lever with the nut.
| 3. INSPECT SHIFT LEVER POSITION SENSOR POSITION |
Apply the parking brake.
Lock the wheels with chocks to secure the vehicle.
Turn the power switch on (READY).
Move the shift lever to D and release the brake.
![]() |
Slowly move the shift lever to N and measure moving distance (A) of the shift lever from the original point to the gear disengagement point.
| *a | Gear Disengagement Point |
| *b | N Position |
| *c | R Position |
| *d | D Position |
Move the shift lever to R and release the brake.
Slowly move the shift lever to N and measure moving distance (B) of the shift lever from the original point to the vehicle disengagement point.
Check that moving distances (A) and (B) shown in the illustration are almost the same.
| 4. ADJUST SHIFT LEVER POSITION SENSOR POSITION |
If moving distance (A) is shorter than (B). [*1]
Move the shift lever to N.
![]() |
Loosen the 2 bolts.
![]() |
Slightly turn the shift lever position sensor counterclockwise.
![]() |
Tighten the 2 bolts in the order shown in the illustration.
Recheck the shift lever position sensor.
If moving distance (B) is shorter than (A). [*2]
Move the shift lever to N.
![]() |
Loosen the 2 bolts.
![]() |
Slightly turn the shift lever position sensor clockwise.
![]() |
Tighten the 2 bolts in the order shown in the illustration.
Recheck the shift lever position sensor.
| 5. INSPECT SHIFT LEVER POSITION |
While moving the shift lever from N to each position, check that the lever moves smoothly and that the shift position indicator comes on properly according to the shift lever position.
Turn the power switch on (READY) and check the following:
When the shift lever is moved to D, the vehicle moves forward.
When the shift lever is moved to R, the vehicle moves in reverse.
| 6. ADJUST SHIFT LEVER POSITION |
Apply the parking brake and move the shift lever to N.
Remove the rear console box assembly (Click here).
![]() |
Slide the adjuster case cover in the direction shown by the arrow.
| *1 | Adjuster Case |
| *2 | Adjuster Case Cover |
![]() |
Using a precision screwdriver, pull out the lock piece of the adjuster case.
| *1 | Adjuster Case |
| *2 | Lock Piece |
Using your fingers, gently pull the cable rod towards the rear of the vehicle to remove backlash.
![]() |
Push in the lock piece of the adjuster case to lock it.
| *1 | Adjuster Case |
| *2 | Lock Piece |
| *3 | Cable Rod |
![]() |
Move the adjuster case cover in the direction shown by the arrow.
| *1 | Adjuster Case |
| *2 | Lock Piece |
| *3 | Adjuster Case Cover |
Install the rear console box assembly (Click here).
| 7. INSTALL ENGINE UNDER COVER LH |