Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Main Body / Data List.

  5. Read the Data List according to the display on the intelligent tester.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Door Courtesy
    Rear door courtesy light switch RH signal/CLOSE or OPEN
    CLOSE: Rear door RH closed
    OPEN: Rear door RH open
    -
    RL Door Courtesy
    Rear door courtesy light switch LH signal/CLOSE or OPEN
    CLOSE: Rear door LH closed
    OPEN: Rear door LH open
    -
    Back Door Courtesy SW
    Back door courtesy switch signal/ ON or OFF
    ON: Back door open
    OFF: Back door closed
    -
    Back Door Open
    Back door lock/Permit or Prohibt
    Permit: Back door unlocked
    Prohibt: Back door locked
    -
    Door Lock SW-Lock
    Door control switch (power window regulator master switch assembly) lock signal/ON or OFF
    ON: Lock side of door control switch (power window regulator master switch assembly) pushed
    OFF: Lock side of door control switch (power window regulator master switch assembly) not pushed
    -
    Door Lock SW-Unlock
    Door control switch (power window regulator master switch assembly) unlock signal/ON or OFF
    ON: Unlock side of door control switch (power window regulator master switch assembly) pushed
    OFF: Unlock side of door control switch (power window regulator master switch assembly) not pushed
    -
    Door Key SW-Lock
    Driver door key-linked lock/unlock switch lock signal/ON or OFF
    ON: Driver door key cylinder turned to lock position
    OFF: Driver door key cylinder not turned to lock position
    -
    Door Key SW-Unlock
    Driver door key-linked lock/unlock switch unlock signal/ON or OFF
    ON: Driver door key cylinder turned to unlock position
    OFF: Driver door key cylinder not turned to unlock position
    -
    FR Door Lock Pos
    Front door RH unlock detection switch signal/LOCK or UNLOCK
    LOCK: Front door RH locked
    UNLOCK: Front door RH unlocked
    -
    FR Door Courtesy
    Front door courtesy light switch RH signal/CLOSE or OPEN
    CLOSE: Front door RH closed
    OPEN: Front door RH open
    -
    FL Door Lock Pos
    Front door LH unlock detection switch signal/LOCK or UNLOCK
    LOCK: Front door LH locked
    UNLOCK: Front door LH unlocked
    -
    FL Door Courtesy
    Front door courtesy light switch LH signal/CLOSE or OPEN
    CLOSE: Front door LH closed
    OPEN: Front door LH open
    -
    RR-Door Lock Pos SW
    Rear door RH and LH unlock detection switch signal/ON or OFF
    ON: Rear door RH or LH unlocked
    OFF: Rear door RH and LH locked
    -
    RL-Door Lock Pos SW
    Rear door RH and LH unlock detection switch signal/ON or OFF
    ON: Rear door RH or LH unlocked
    OFF: Rear door RH and LH locked
    -


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Main Body / Active Test.

  5. Perform the Active Test according to the display on the intelligent tester.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Door Lock
    Door lock motor
    Unlock/Lock
    -
    Trunk and Back-Door Open
    Back door lock motor
    OFF/ON
    -