FRONT SUSPENSION MEMBER > REMOVAL |
| 1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
| 2. SECURE STEERING WHEEL |
![]() |
Secure the steering wheel with the seat belt in order to prevent rotation.
| 3. REMOVE COLUMN HOLE COVER SILENCER SHEET |
![]() |
Remove the 2 clips and the column hole cover silencer sheet.
| 4. SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY |
![]() |
Put matchmarks on the steering sliding yoke sub-assembly and steering gear assembly.
| *a | Matchmark |
Loosen bolt A.
Remove bolt B.
Separate the steering sliding yoke sub-assembly from the steering gear assembly.
| 5. SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
![]() |
Remove clip A, detach clip B from the body and disconnect the No. 1 steering column hole cover sub-assembly.
| 6. REMOVE FRONT WHEEL |
| 7. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH |
![]() |
Remove the nut and separate the front stabilizer link assembly LH from the front stabilizer bar.
| 8. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH |
| 9. SEPARATE TIE ROD END SUB-ASSEMBLY LH |
Remove the cotter pin and nut.
![]() |
Install SST to the tie rod end.
Secure SST using a string.
Using SST, separate the tie rod end from the steering knuckle.

| *1 | Center Nut | - | - |
| *a | String | *b | Grease Application Area |
| *c | Place the wrench here. | - | - |
| 10. SEPARATE TIE ROD END SUB-ASSEMBLY RH |
| 11. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH |
![]() |
Remove the clip and nut.
![]() |
Install SST to the threaded section of the lower ball joint.
Using SST, separate the front lower No. 1 suspension arm sub-assembly LH from the steering knuckle.

| *a | Apply grease | *b | Place wrench here |
| 12. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH |
| 13. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
![]() |
Using a jack and a wooden block, support the engine and transaxle assembly.
| *1 | Jack |
| *2 | Wooden Block |
![]() | Front of the Vehicle |
![]() |
Remove the bolt and separate the engine moving control rod.
![]() |
Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.
| *1 | Engine Lifter |
| *2 | Attachment |
![]() | Front of the Vehicle |
![]() | Attachment Placement Location |
Remove the 6 bolts and front suspension crossmember sub-assembly.

Slowly lower the front suspension crossmember sub-assembly.
| 14. REMOVE STEERING LINK ASSEMBLY |
![]() |
Remove the 2 bolts, 2 nuts and steering link assembly from the front suspension crossmember sub-assembly.
| 15. REMOVE FRONT NO. 1 STABILIZER BRACKET LH |
![]() |
Remove the 2 bolts and front No. 1 stabilizer bracket LH from the front suspension crossmember sub-assembly.
| 16. REMOVE FRONT NO. 1 STABILIZER BRACKET RH |
| 17. REMOVE FRONT STABILIZER BAR |
| 18. REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH |
![]() |
Remove the bolt and front lower No. 1 suspension arm sub-assembly LH from the front suspension crossmember sub-assembly.
| 19. REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH |
| 20. REMOVE ENGINE MOVING CONTROL ROD |
![]() |
Remove the bolt and engine moving control rod from the front suspension crossmember sub-assembly.