REAR AIRBAG SENSOR > REMOVAL |
| 1. PRECAUTION |
| 2. REMOVE REAR SEAT HEADREST ASSEMBLY |
| 3. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY (for LH Side) |
| 4. REMOVE FRONT FLOOR COVER RH |
![]() |
Using a clip remover, remove the 2 clips <A>.
Disengage the 3 clips <B>.
![]() |
Disengage the 3 guides and remove the front floor cover RH.
| 5. REMOVE FRONT FLOOR COVER LH |
![]() |
Using a clip remover, remove the 2 clips <A>.
Disengage the 3 clips <B>.
![]() |
Disengage the 3 guides and remove the front floor cover LH.
| 6. REMOVE FRONT CENTER FLOOR COVER |
![]() |
Using a clip remover, remove the 3 clips.
Disengage the 2 guides and remove the front center floor cover.
| 7. REMOVE REAR SEAT CUSHION ASSEMBLY |
![]() |
Disengage the 2 clips.
| *a | RH Side |
| *b | LH Side |
![]() |
Disengage the hook of the rear seat cushion assembly from the vehicle body as shown in the illustration.
| a | 100 mm (3.94 in.) or less |
Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.
Repeat the step above for the other hook.
Remove the rear seat cushion assembly.
| 8. REMOVE REAR SEATBACK ASSEMBLY |
| 9. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL |
| 10. REMOVE REAR DOOR SCUFF PLATE |
![]() |
Disengage the 5 claws and guide and remove the rear door scuff plate LH.
| 11. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP |
| 12. REMOVE DECK BOARD ASSEMBLY |
Remove the deck board assembly.
| 13. REMOVE DECK FLOOR BOX LH |
Remove the deck floor box LH.
| 14. REMOVE DECK FLOOR BOX RH |
| 15. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY |
Remove the package tray trim panel assembly.
| 16. REMOVE REAR DECK TRIM COVER |
![]() |
Remove the 2 clips.
Disengage the 4 claws and 2 guides, and remove the rear deck trim cover.
| 17. DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY |
Remove the bolt.
![]() |
Disengage the 2 claws and disconnect the floor anchor of the rear seat 3 point type outer belt assembly.
| 18. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for LH Side) |
![]() |
Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
| *1 | Protective Tape |
Disconnect the connector and remove the No. 1 luggage compartment light assembly.
| 19. REMOVE DECK TRIM SIDE PANEL ASSEMBLY |
Turn the rear seatback hinge in the direction indicated by the arrow shown in the illustration.

| *1 | Rear Seatback Hinge | - | - |
Remove the bolt and 2 screws.
Disengage the 4 claws, 4 clips and guide, and remove the deck trim side panel assembly LH.
| 20. REMOVE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY |
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
Disconnect the connector from the side No. 2 airbag sensor assembly.
Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

| *1 | White Housing Lock | *2 | Yellow CPA |
| *a | Connector Lock is Released | - | - |
Push down the white housing lock again and disconnect the connector.
![]() |
Remove the bolt and side No. 2 airbag sensor assembly from the vehicle body.
After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

| *a | Incorrect | *b | Correct |