INVERTER WITH CONVERTER > REMOVAL |
| 1. PRECAUTION |
| 2. REMOVE SERVICE PLUG GRIP |
| 3. DRAIN COOLANT (for Inverter) |
Remove the reserve tank cap.
![]() |
Loosen the radiator drain cock plug and drain the coolant.
Tighten the radiator drain cock plug.
| 4. REMOVE INVERTER TERMINAL COVER |
![]() |
Remove the 2 bolts and inverter terminal cover.
| *1 | Interlock Connector |
| 5. REMOVE INVERTER COVER |
![]() |
Remove the 7 bolts and inverter cover.
| 6. CHECK TERMINAL VOLTAGE |
![]() |
Using a voltmeter, measure the voltage between the terminals of the 2 phase connectors.
| 7. DISCONNECT ENGINE ROOM MAIN WIRE |
![]() |
Raise the lock lever and disconnect the inverter with converter connector.
![]() |
Disconnect the engine wire from the engine room main wire.
![]() |
Disconnect the hose clamp.
Remove the 2 bolts.
Disconnect the clamp and engine room main wire.
| 8. DISCONNECT FRAME WIRE |
![]() |
Disconnect the harness clamp.
![]() |
Remove the 4 bolts, and disconnect the frame wire (high voltage cables of the hybrid battery) from the inverter with converter assembly.
| 9. DISCONNECT MOTOR CABLE |
Disconnect the motor cable (for MG 1)
![]() |
Remove the 5 bolts, and disconnect the high voltage cables of the motor cable for (MG1) from the inverter with converter assembly.
Disconnect the motor cable (for MG 2)
![]() |
Remove the 5 bolts, and disconnect the high voltage cables of the motor cable (for MG2) from the inverter with converter assembly.
| 10. DISCONNECT NO. 2 ENGINE WIRE |
![]() |
Remove the bolt (A).
Remove the 4 bolts (B), and disconnect the No. 2 engine wire (high voltage cables for the air conditioning compressor) from the inverter with converter assembly.
| 11. INSTALL INVERTER COVER |
![]() |
Temporarily install the inverter cover with the 7 bolts to prevent any foreign matter or water from entering the inverter with converter assembly.
| 12. INSTALL INVERTER TERMINAL COVER |
![]() |
Temporarily install the inverter terminal cover with the 2 bolts to prevent any foreign matter or water from entering the inverter with converter assembly.
| *1 | Interlock Connector |
| 13. DISCONNECT FRAME WIRE |
![]() |
Remove the relay block cover.
![]() |
Disconnect the connector.
![]() |
Disengage the 2 claws and remove the No. 1 relay block cover.
![]() |
Remove the nut and disconnect the No. 2 engine room wire.
Release the 2 claws, and disconnect the No. 2 engine room wire.
| 14. DISCONNECT NO. 1 INVERTER COOLING HOSE ASSEMBLY |
![]() |
Release the retainer and disconnect the No. 1 inverter cooling hose assembly from the inverter with converter assembly.
| *1 | Retainer |
![]() |
Put pieces of cloth into the pipes and in the disconnected hose, or cover the pipes and hoses with plastic bags as shown in the illustration to prevent foreign matter from entering the cooling system and to prevent coolant from spilling near the inverter with converter assembly.
| 15. DISCONNECT NO. 2 INVERTER COOLING HOSE ASSEMBLY |
![]() |
Release the retainer and disconnect the No. 2 inverter cooling hose assembly from the inverter with converter assembly.
| *1 | Retainer |
![]() |
Put pieces of cloth into the pipes and in the disconnected hoses, or cover the pipes and hose with plastic bags as shown in the illustration to prevent foreign matter from entering the cooling system and to prevent coolant from spilling near the inverter with converter assembly.
| 16. REMOVE INVERTER WITH CONVERTER ASSEMBLY |
![]() |
Temporarily secure the No. 3 engine room wire with the inverter with converter assembly protector as shown in the illustration.
| *1 | Protector |
![]() |
Remove the 3 bolts and inverter with converter assembly.
![]() |
Even after the coolant is drained, coolant remains in the inverter due to its internal structure. Therefore, seal or cover the pipes when removing the inverter so that coolant does not spill out.
| 17. REMOVE HIGH VOLTAGE FUSE |
![]() |
Remove the 2 bolts and inverter terminal cover.
| *1 | Interlock Connector |
![]() |
Remove the 7 bolts and inverter cover.
![]() |
Remove the 2 bolts and high voltage fuse from the inverter with converter assembly.
![]() |
Temporarily install the inverter cover with the 7 bolts to prevent any foreign matter or water from entering the inverter with converter assembly.
![]() |
Temporarily install the inverter terminal cover with the 2 bolts to prevent any foreign matter or water from entering the inverter with converter assembly.
| *1 | Interlock Connector |