Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV RELAY ASSEMBLY

HV RELAY ASSEMBLY > INSPECTION

for Preparation Click here



1. INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY


  1. Inspect SMRB.



      A259731E16
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A-1 (+) - P5-1 (CBI)
      Auxiliary battery voltage is not applied between terminals M40- 1 (SMRB) and M40-2 (GND)
      10 kΩ or higher
      A-1 (+) - P5-1 (CBI)
      Auxiliary battery voltage is applied between terminals M40- 1 (SMRB) and M40-2 (GND)
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Hybrid Battery Junction Block Assembly)

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      M40-1 (SMRB) - M40-2 (GND)
      -40 to 80°C (-40 to 176°F)
      25.0 to 59.0 Ω

      If the result is not as specified, replace the hybrid battery junction block assembly or electric vehicle fuse.



  1. Inspect SMRG.



      A259731E17
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      c1-1 (-) - P4-1 (CEI)
      Auxiliary battery voltage is not applied between terminals M40- 3 (SMRG) and M40-2 (GND)
      10 kΩ or higher
      c1-1 (-) - P4-1 (CEI)
      Auxiliary battery voltage is applied between terminals M40- 3 (SMRG) and M40-2 (GND)
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Hybrid Battery Junction Block Assembly)

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      M40-3 (SMRG) - M40-2 (GND)
      -40 to 80°C (-40 to 176°F)
      25.0 to 59.0 Ω

      If the result is not as specified, replace the hybrid battery junction block assembly.



  1. Inspect SMRP.



      A259731E22
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      P4-1 (CEI) - c1-1 (-)
      Auxiliary battery voltage is not applied between terminals M40-4 (SMRP) and M40-2 (GND)
      10 kΩ or higher
      P4-1 (CEI) - c1-1 (-)
      Auxiliary battery voltage is applied between terminals M40-4 (SMRP) and M40-2 (GND)
      28.5 to 31.5 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Hybrid Battery Junction Block Assembly)

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      M40-4 (SMRP) - M40-2 (GND)
      -40 to 80°C (-40 to 176°F)
      112 to 274 Ω

      If the result is not as specified, replace the hybrid battery junction block assembly.