Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function)

DTC    B2274    ACC Monitor Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction in the ACC circuit is detected. The ACC circuit activates the ACC relay.

HINT:
When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2274
Malfunction in the ACC circuit of the certification ECU (smart key ECU assembly)(1-trip detection logic*).

HINT:
When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.

  1. AM2 fuse
  2. ACC relay (Instrument panel junction block assembly)
  3. Certification ECU (Smart key ECU assembly)
  4. Wire harness or connector
Wait 10 seconds after turning the power switch on (ACC) or on (IG), and then wait another 10 seconds after turning the power switch off.
  1. *: Only detected while a malfunction is present.

Vehicle Condition and Fail-safe Function when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
  1. If there is a malfunction due to the relay being stuck on, the ACC relay does not turn off even though the power switch is off.
  2. If there is a malfunction due to the relay being stuck off, the ACC relay does not turn on even though the power switch is on (ACC).

HINT:
The power switch can be turned on (IG) and the hybrid control system can be started.

-

WIRING DIAGRAM


B392457E02


INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:
    for Power Source Control: Body / Power Source Control / DTC.
    for Entry&Start: Body / Entry&Start / DTC.
  2. The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.
  4. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  5. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.


HINT:

Related Data List and Active Test Items 
DTC
Data List Item
Active Test Item
B2274
Power Source Control
  1. ACC Relay Monitor
-

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
B268625E34
  1. Disconnect the G77 connector from the certification ECU (smart key ECU assembly).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G77-2 (+B) - Body ground
    Power switch off
    11 to 14 V

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Certification ECU (Smart Key ECU Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE
OK


2.CHECK HARNESS AND CONNECTOR (GROUND)
B268625E35
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G77-11 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Certification ECU (Smart Key ECU Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the G79 connector from the certification ECU (smart key ECU assembly).

  1. Disconnect the 3B connector from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G79-4 (ACCD) - 3B-37
    Always
    Below 1 Ω
    3B-8 - Body ground
    Always
    Below 1 Ω
    G79-4 (ACCD) or 3B-37 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)


  1. Remove the instrument panel junction block assembly (Click here).


    E219653E02


    Text in Illustration 
    *1
    for LHD
    *2
    for RHD
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3E-1 - 3B-13*1
    3F-1 - 3B-13*2
    Auxiliary battery voltage not applied to terminals 3B-37 and 3B-8
    10 kΩ or higher
    Auxiliary battery voltage applied to terminals 3B-37 and 3B-8
    Below 1 Ω

    1. *1: for LHD
    2. *2: for RHD



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK


5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
B268626E12
  1. Reconnect the G79 certification ECU (smart key ECU assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G79-4 (ACCD) - Body ground
    Power switch off → Power switch on (ACC)
    1 V or less → 8.5 V or higher

    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU (Smart Key ECU Assembly))



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (Click here)
OK

END (USE SIMULATION METHOD TO CHECK) (Click here)